Koso 10032749 Quick Start Manual

INSTRUCTION
●Thank you for purchasing the KOSO heated grips. Before installing, please read the instruction carefully and keep it for future reference.
ATTENTION!
● For installation, please follow the steps described in manual. Any damage caused by wrong installation shall be imputed to the users.
● Don't break or modify the wire. To avoid the short circuit, please don't pull the wire when installing.
●
Do not disassemble or change any parts excluding the manual description.
●
The interior examination or maintenance should be executed by our professionals.
◎MARK MEANING:
You could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
Some processes must be followed to avoid the damage to the vehicle.
If any information dealt with in the manual remains unclear seek professional assistance.
1 Accessories
1 2
Heated grip X2 G type switch X1
Adapter plate for switch
5 6
M3XP0.5X25L screw X1
X1
9
G l u e X1
Please contact your local distributor if the items received are not the same as the one listed above.
2-1 Specifications
34.8 mm 16.5 mm
2-2 Heated grip testing data
(℃)
120
100
80
60
40
20
0
0 5 10 15
The testing environment is under 26 Degrees Celsius, with working voltage of 13.5 V.
3 4
Connecting wire X1
7 8
M3 nut X1 Bar-end cap X2
● Heating stage
1st stage (low) ~ 5th stage (high)
● Fuse type
4A (ASP)
● Effective temperature range
JIS D 0203
● Voltage
DC 12 V
● Switch size
W38.2 X L38.2 X H16.5 mm
● Switch weight (with wire)
About 88 g
Design and specifications are subject to change without notice!
Level 5 Temperature Curve
Level 4 Temperature Curve
Level 3 Temperature Curve
Level 2 Temperature Curve
Level 1 Temperature Curve
20 25 30 (Minute)
3-1 Practical installation instruction
Please proceed as follows
Figure 1
FLASH LIGHT ON
Figure 2
PRESS THE PRESS THE
BUTTON BUTTON 3
ONCE SECONDS
Velcro X1
Figure 3
3-2 Installation instruction
5.
3-3 Wiring installation instructions
G type switch (Accessory 2)
1. Please use an appropriate
Figure 4
tool to remove the original
Need to keep cetrain clearace
handlebar.
2. Please apply a cleaning
agent and wipe back and
forth to clean away the
residual glue from the
handlebar.
3.Thrust the heated grip into
Figure 5
the handlebar.
If the heating grip and the
handlebar are under
tighten; then apply the
super glue (Accessory 9)
to strengthen the
tightness to ensure there
will be no twisting during
riding.
To install, please do not use the
tool to knock on or twist to thrust
in the heating grip for thus doing
will break or damage the wire
inside the handlebar.
Installation steps
1.
1. G switch (Accessory 2)
2.
Velcro (Accessory 4)
3. Adapter plate for switch (Accessory 5)
2.
M3XP0.5X25L screw (Accessory 6)
4.
M3 nut (Accessory 7)
5.
3.
4.
0.2 Nm (2 kgf.cm)
Connecting wire (Accessory 3)
To install the heating grip onto
the throttle sleeve in right side,
please note that throttle must be
maintained a safe clearance
plus a suitable surplus of wiring;
also they shall be tested by
rotating to and fro for avoiding
interference.
4.To install the side cap onto
the heating grip, please
1.
insert the top cap into the
top groove and then follow
to push it downward into the
bottom groove.
2.
0.2 Nm (2 kgf.cm)
Black / Ground wire connect to the vehicle
body or the engine (It must be a good ground)
Red / Positive wire connecting
to the key on switch (DC 12 V)
Heated grip (Accessory 1)
wh000axg1a