Table of Contents
Advertisement
Quick Links
Diagnostic and Service Tools for PROFIBUS
PROFI-TM Professional
USER MANUAL
Indu-Sol GmbH • Blumenstrasse 3 • D - 04626 Schmoelln • Germany
Phone: +49 34491 5818-0 • Fax: +49 34491 5818-99 • e-mail: info@indu-sol.com • www.indu-sol.com
Your partner and specialist for field bus systems, Industrial Ethernet and PROFInet
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Indu-Sol PROFI-TM Professional
Summary of Contents for Indu-Sol PROFI-TM Professional
- Page 1 USER MANUAL Indu-Sol GmbH • Blumenstrasse 3 • D - 04626 Schmoelln • Germany Phone: +49 34491 5818-0 • Fax: +49 34491 5818-99 • e-mail: info@indu-sol.com • www.indu-sol.com Your partner and specialist for field bus systems, Industrial Ethernet and PROFInet...
-
Page 2: Table Of Contents
© Copyright 2010 Indu-Sol GmbH Contents No part of this manual may be reproduced, photocopied, stored on a retrieval Introduction system, transmitted, processed or translated without the express prior written General consent of Indu-Sol GmbH. Test Functions Operating Modes of the Tool... -
Page 3: Test Functions
Trigger input/output 1.3 Operating Modes of the Tool You can connect the PROFI-TM Professional to a PC or notebook, or run it in stand-alone mode. The PC mode provides all standard and expert tests. You can also select individual stations you want to test. The stand-alone mode currently provides the live status and the master simulator mode. -
Page 4: Pc-Software Profibus Diagnostics Suite
• Test tool with RS485 interface • Simply connect the PROFI-TM Professional to the USB interface of a PC or Wide-range power supply with European and US mains power cables • notebook. You can then use the included “PROFIBUS Diagnostics Suite” PC Connecting cable for direct power supply with 24 VDC •... -
Page 5: Optional Accessories
Order no: 00110189 3.2 Adapter Set for M12 Connection Technology Using the M12 adapter set, you can connect the PROFI-TM Professional to field devices with M12 connectors. The set comprises an M12 adapter cable with special pin layout and an M12 terminating resistor that you can screw on, if required. -
Page 6: Active Measuring Point „Pbma" Ip20 - Active Terminator
Fig. 5: M12 Active Measuring Point for measurements at running systems. Order no.: PBMX-Set: 00010519 Order no.: PMBX: 00010518 Fig. 4: PROFIBUS D-sub service interface for testing a live bus Order no: 00010515 Indu-Sol GmbH Page 11 Page 12 © 2010... -
Page 7: Connectors And Controls
Connection to Power Supply Connection to Notebook/PC 24 VDC 5.1 Power-Up Behavior without USB Connection Status-LED Trigger-Input The PROFI-TM Professional starts up in stand-alone mode in this case (see page 26) and is immediately ready for testing. Status-LED Trigger-Output Detail: Terminal block for trigger in/output Fig. -
Page 8: Power-Up Behavior When Usb Connected
When you start the PROFIBUS Diagnostics Suite control and evaluation port on the PC or notebook. When you use external USB hubs or software on your computer and select the PROFI-TM Professional and a notebook docking stations for connection, problems can occur. -
Page 9: Connection Types
7.1.3 Adapter cable The PROFI-TM Professional is supplied with the D-sub adapter cable 2 and is required for using the master simulator and the topology scan feature (see page 23). The short D-sub adapter cable 1 (purple, optional deliverable) allows connection to a live PROFIBUS with minimum influence on bus operation. -
Page 10: Simple Connection For Tests During System Shutdown
If all bus stations provide D-sub connectors with an additional service socket, To test a live PROFIBUS with the PROFI-TM Professional during operation, you can simply plug in the PROFI-TM Professional at that socket (see figure appropriate connection possibilities have to be provided. If no suitable connec- below). -
Page 11: Anschlussart D-Sub-Stecker Mit Service-Buchse
If all bus stations provide D-sub connectors with an additional service socket, To test a live PROFIBUS, you will need additional D-sub service interface of you can simply plug in the PROFI-TM Professional at that socket (see figure the type “PBMA”. -
Page 12: Connection Via M12 Connector
Both features can only be used during shutdown of the installation. You have used as connection points for the test tool. For this reason, tests can often only to use to D-sub adapter cable 2 (supplied with PROFI-TM Professional). The be performed at a bus end. -
Page 13: Special Case: Active Devices At Both Ends Of The Bus
Display and Control in Stand-Alone Mode Attention: Bus stations must only be disconnected from the power The PROFI-TM Professional always starts in stand-alone mode unless it is supply or the bus during shutdown of the installation. USB connected to a PC or notebook. The readings are shown on the display. -
Page 14: Operating Concept
Display: “M.Sim. ON” The only control on the main display is the down arrow key with which you can select the individual functions. Fig. 18: Display control with the four function keys Indu-Sol GmbH Page 27 Page 28 © 2010... -
Page 15: Functions
“-” display 4. One or more bus stations have been added and one or more dropped Fig. 21: Live Status with station status of a master during the test: • “+ -” display Indu-Sol GmbH Page 29 Page 30 © 2010... -
Page 16: Quick Test Function
Note: The update rate for the live status substantially depends on the number 10 Maintenance and Servicing of bus stations and the signal quality. The PROFI-TM Professional is maintenance-free and does not require calibra- 8.3.2 Quick Test function tion. Repairs may only be carried out by the device manufacturer. All returns This function is currently in preparation and will be available via firmware must be made in the supplied carrying case. -
Page 17: Troubleshooting
HxWxD: 35 x 170 x 110 mm Weight Test tool without cable: approx. 0.45 kg, If you need to contact Indu-Sol support team, you will find the contact data on complete with carrying case, without accessories: approx. 3.9 kg the back cover of the manual. -
Page 18: General Notes
Softing AG on request. NOTE: For compliance with the legal EMC requirements, the other components Indu-Sol GmbH www.indu-sol.com (PROFIBUS devices, AC adapter, etc.) must also meet these requirements. To meet the EMC conditions, the product must be installed and connected in Blumenstrasse 3 Phone.
Need help?
Do you have a question about the PROFI-TM Professional and is the answer not in the manual?
Questions and answers