Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Climecon CleanMaster Series
Summary of Contents for Climecon CleanMaster Series
- Page 1 CleanMaster® INSTALLATION MANUAL AND QUICK GUIDE climecon.fi...
- Page 2 FILLED IN CORRECTLY and that all the necessary tests have been per- formed and recorded! You can also order the commissioning, installation, (excluding hauling and HVAC contract work) training and maintenance services directly from Climecon. Lämmittäjänkatu 4 A 00880 HELSINKI Puh.
-
Page 3: Table Of Contents
14. Installing the grease separators and locking the SlideSafe safety lock ....18 15. Maintenance instructions for CleanMaster® hoods ..........19 16. Updating the Climecon CleanMaster® software ...........23 17. Climecon CleanMaster® – updating an external controller ........24 General delivery and warranty terms .................26 © Climecon... -
Page 4: General
Climecon or the dealer. The period of notice is five days after the delivery. Climecon Oy is not liable for any costs accrued due to replacing products that have been installed in violation of the installation instructions. -
Page 5: The Content Of Cleanmaster® Hood Deliveries
• The UV lamps’ voltage supply from the UV control unit’s terminal block to the hood’s quick con- nectors (e.g. control cable Ölfex 4 x 1.5mm2) • Mounting accessories • Cables to the SlideSafe safety lock © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 6: Warnings
Only Climecon’s own replacement parts and UV lamps can be used in the CleanMaster® system. The validity of the warranty requires that only Climecon’s own replacement parts and UV lamps are used. No replacement parts or UV lamps other than original ones or ones ordered from Climecon can be used for the device. -
Page 7: Cleanmaster Quick Guide
Easily removable supply air slats for maintenance Supply air Grommets for the control device (with strain reliefs) Climecon OptiLUMO LED light* End wall (removable for units with several modules) Danger of electric shock! Electricity supply to the control device NOTE! Electrical connections may only be made by a professional electrician. -
Page 8: Installation Instructions For Cleanmaster® Hoods
M6 bolt and nut. If the unit in question has several hoods, seal the seam with appropriate adhesive mass, such as 3MTM. Hybrid glue/sealant mass 760 UV © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 9: Electrical Connections Of The Cleanmaster Hood
The safety switch has to be clearly visible and the label climecon.fi/clm included in the delivery must be attached to it! © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 10: Operation Modes (A, B Or C)
All in slave mode + ModBus address Physical BAS Control (overrides ModBus) • Control via ModBus • Modbus master not supplied • ModBus master (building automation) © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 11: Starting The Cleanmaster Hood
1. Choose your language Finnish, Swedish or English 2. Master/Slave Climecon CleanMaster can be the device’s Master or Slave device. The choice between Master or Slave is made when the device is started for the first time. - Page 12 For other settings than the hood controller’s basic settings, please read through the separate user manual, downloadable from climecon.fi/clm. The Climecon CleanMaster system can also be connected to the external ModBus control device. In this case, a Slave address in the range of 1–250 will be defined for all devices. The ModBus parameter map is available through Climecon Oy’s customer service.
-
Page 13: Disconnecting The Grease Separators
6.3 Replacing the fluorescent tubes of lights Open the lamp’s cover glass by opening its attachment screws. Replace the fluorescent tubes. Check that the sealants are undamaged. Reinstall the cover glass. © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 14: Changing The Uv Lamp
Replace the UV lamp. Only Climecon’s UV lamps can be Attach the new UV lamp to Attach the UV lamp’s electrical Install all grease separators back into the hood. used in the CleanMaster® sys-... -
Page 15: Adjustment Instructions For Cleanmaster® Hoods
These adjustments can be made by first turning the hand knobs of the control air unit, then moving them sideways and finally locking the position by retightening the hand knobs. © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 16: K Value Table Of Cleanmaster®-Hoods
Control air/Hood width (mm) Adjustment position 1000 1500 2000 2500 3000 Maximum (Fully open) Minimum (Half open)* *Recommended to be used if supply air pressure exceeds 15 Pa. © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 17: Installing The Uv Lamp
Attach the UV lamp’s power cords to the holes in the fastenings with cable ties and roll up any extra cords so that they do not lie in the grease. NOTE! Do not attach the cords directly to the lamp! © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 18: Installing The Grease Separators And Locking The Slidesafe Safety Lock
NOTE! The CleanMaster® system will not start if the SlideSafe safety lock has not been locked properly. © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 19: Maintenance Instructions For Cleanmaster® Hoods
The hoods are cleaned with detergents suitable for stainless steel. The use of highly alkaline substances (pH > 11) should be avoided. Climecon’s UV lamps do not need to be cleaned in normal conditions. 5.1 Cleaning the hoods Clean the hood’s surfaces by wiping them gently. - Page 20 © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600...
- Page 21 © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600...
- Page 22 © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600...
-
Page 23: Updating The Climecon Cleanmaster® Software
IMPORTANT! REMOVE THE MEMORY CARD If you are using a separate external controller, you will also need to update its software version. See the separate set of instructions for this, ‘Climecon CleanMaster external controller update.pdf’. © Climecon Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600... -
Page 24: Climecon Cleanmaster® - Updating An External Controller
17. Climecon CleanMaster® – updating an external controller IMPORTANT! Before updating the external controller, the CleanMaster® hood/IV ceiling hardware has to be updated. See ‘Climecon CleanMaster 2G – software update.pdf’ Detach the external controller’s cord. Press the ‘Home’ + ‘ESC’ buttons and hold them down. - Page 25 EU compliance 1. The product’s ID number: CleanMaster professional kitchen hood – 2. Name and address of the manufacturer or its authorised representative: Climecon Oy Lämmittäjänkatu 4 00880 Helsinki +358 (0)20 198 6600 info@climecon.fi 3. This declaration of conformity has been given at the manufacturer’s sole responsibility.
-
Page 26: General Delivery And Warranty Terms
Interest Act. If the Buyer’s payment is delayed by more than thirty (30) days after the due date, Climecon has the right to halt all its own performances without any liability penalties until the Buyer has fulfilled all its overdue payments to Climecon. - Page 27 General delivery and warranty terms As an exception to this, Climecon grants its UV lamps a warranty of up to sixteen thousand (16,000) hours of use. If a UV lamp becomes damaged before these hours are up, Climecon will reimburse the remaining hours of use in the acquisition costs of the new lamp.
Need help?
Do you have a question about the CleanMaster Series and is the answer not in the manual?
Questions and answers