ATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REF- ERENCE . Safety Instructions Read this user’s guide before you operate your projector and save it for future reference. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
In the event this product is found to be defective within the warranty period, BENQ’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, imme- diately notify the dealer from which you purchased the product of any defects.
— Consult the dealer or an experienced radio/TV technician for help. EEC Statement This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements. BenQ PB8230/ PB8220/ PB8120 User’s Guide Introduction...
BenQ PB8230/ PB8220/ PB8120 User’s Guide Shipping Contents The Projector is shipped with the cables required for connection to standard PC or laptop computers. Carefully unpack and verify that you have all the items shown below. If any of these items are missing, please contact personnel at the place of purchase.
IR remote sensor Ventilation grill Speaker Projection lens adjuster RGB signal input RGB signal output connector BenQ PB8230/ PB8220/ PB8120 User’s Guide Audio/ Video connector Audio jack USB mouse connector S-Video jack RS 232 control port Rear adjuster feet Kensington lock...
BenQ PB8230/ PB8220/ PB8120 User’s Guide External Control Panel Power Presses and holds the Power key to turn the projector on or off. Auto Automatically determines the best picture settings for current received signals. Left/ Keystone - Right/ Keystone + Menu will display the menu system on screen.
Adjuster The projector is equipped with 2 quick-release adjuster feet. Push the buttons to adjust its tilt angle. Lift the projector up and press the adjuster button to release the adjuster. The adjuster will drop into position and be locked.
BenQ PB8230/ PB8220/ PB8120 User’s Guide Remote Control Description Power Menu 3 Left/ Keystone - 4 Right/ Keystone + Auto L-Click/ R-click Zoom in/ out By pressing ZOOM IN +, the center of the picture will be magnified. When the + button is pressed again, the picture is further magnified, up to four times the original size.
Remote control effective range The remote sensors are located on the front and the back of the projector. It can function in a range of 30 degrees horizontally and 30 degrees vertically relative to a line that is a right angle to the remote sensors. The distance between the remote control and the remote sensors must be shorter than 6 meters (19.5 feet).
BenQ PB8230/ PB8220/ PB8120 User’s Guide INSTALLATION Screen Size Place the projector at the required distance from the screen according to the desired picture size (see the table below). • PB8230/ PB8220 (XGA) screen size chart Diagonal measurement Distance from...
13.70 164.3 16.77 14.67 176.1 17.97 15.65 187.8 19.17 Connecting to Various Equipment HDTV description The projector is capable of displaying various High Definition TV display modes. Some of these sources are: • Digital-VHS (D-VHS) player • Satellite Dish HDTV receiver Most of these sources will provide an analog component video output, a standard VGA output, or a YPBPR (default) format.
Page 16
BenQ PB8230/ PB8220/ PB8120 User’s Guide Connecting to Various Equipment It only takes a few seconds to connect your projector to your desktop or notebook computer, VCR, or other systems. However, a Mac adapter (an optional accessory) is needed for connection to Macintosh computers.
(When the power is turned off, there is a 120-second cooling period before the projector can be re-started.) Switch on all connected equipment. BenQ PB8230/ PB8220/ PB8120 User’s Guide Remote Control Projector Operation...
To correct this, press KEYSTONE +/- (hot key) on the control panel of the projector or on the remote control, and then adjust the sliding bar labeled Keystone, as needed. Press + to correct keystoning at the top of the image.
Menu Bar Sub-menu Display Keystone Brightness Contrast Phase H. Size Y/Pb/Pr Keystone Brightness Video Contrast Color Tint S-Video BenQ PB8230/ PB8220/ PB8120 User’s Guide Source Image Source Ratio Mirror H-position Source V-position Volume Color Temp Treble Information Bass Mute Ratio...
BenQ PB8230/ PB8220/ PB8120 User’s Guide 1. Display Menu FUNCTION DESCRIPTION Corrects any keystoning of the image. Keystone Adjusts the brightness of the image. Brightness Adjusts the degree of difference between dark and light in the image. Contrast Adjusts to avoid the occurrence of flicker.
*This function is not available when the input mode is PC. Adjusts the image to make it appear more red or blue. Tint *This function is available only when the selected System is NTSC. BenQ PB8230/ PB8220/ PB8120 User’s Guide DESCRIPTION 2. 16:9 3. 1:1...
BenQ PB8230/ PB8220/ PB8120 User’s Guide 3. Source Menu FUNCTION Mirror Source Volume Treble Bass Mute Operation DESCRIPTION Default Rear screen projection Selects the input source from among PC, Video, S-Video, and YP when several sources are available. Adjusts the volume level.
BenQ PB8230/ PB8220/ PB8120 User’s Guide 4. Control Menu FUNCTION DESCRIPTION Language sets the language for the OSD control menus. Use the 3 / 4 key to select the desired language from Language among English, French, German, Italian, Spanish, Korean, Simplified Chinese and Traditional Chinese.
BenQ PB8230/ PB8220/ PB8120 User’s Guide 5. PIP Menu These functions are available only when the input mode is PC and the PIP source is Video or S-Video. FUNCTION PIP Source PIP Size PIP Position H. Position V. Position More Options...
Please do not unplug the power cord before POWER is shut down or dur- ing the two-minute cooling process. If the projector is not properly shut down, to protect the lamp, the sys- tem will detect this and cool the lamp for two minutes automatically before turning on again.
The LAMP indicator will light up if the lamp becomes too hot. Turn off the power and let the projector cool for 45 minutes. If the LAMP indicator is still red when turning the power on, please contact your dealer.
Lamp Replacement Caution To reduce the risk of electrical shock, always turn off the projector and dis- connect the power cord before changing the lamp. Turn off the projector. Disconnect the power cord from the outlet and the projector. Loosen the screw and remove the lamp cover.
BenQ PB8230/ PB8220/ PB8120 User’s Guide Caution To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.
250W lamp module ......... . 65.J4002.001 Ordering Parts or Getting Information For product information, product assistance, service information, or to order accessories, please visit the BENQ Corporation website at http://www.BenQ.com. BenQ PB8230/ PB8220/ PB8120 User’s Guide Maintenance...
TIME. YOU HAVE TO CHANGE THE LAMP! OUT OF LAMP USAGE TIME. CHANGE THE LAMP! BenQ PB8230/ PB8220/ PB8120 User’s Guide Description Projector is searching for input. Projector has identified the input signal and is running the auto image adjustment function.
BenQ PB8230/ PB8220/ PB8120 User’s Guide SPECIFICATIONS Projector Specifications Technical Specifications Note: All specifications are subject to change without notice. General Product name Model name Optical Display system Lens F/Number Lamp Electrical Power supply Power consumption Mechanical Dimensions Operating temperature...