Milwaukee 4004-20 Operator's Manual page 6

Moving the Handle to the Other Side
For Cat. Nos. 4125 & 4130 only
Bubble level
Socket
screws (4)
Cradle
1. Tighten the cradle lock.
2. Loosen the socket head screw and remove the
meter box.
3. Remove four (4) socket head screws holding the
spoked handle housing.
4. Turn the assembly around 180°.
5. Replace the four (4) socket head screws and
tighten securely.
6. Attach meter box to opposite side (see "Mounting
the Meter Box").
For Cat. Nos. 4115 & 4120 only
Cradle
1. Loosen the cradle lock.
2. Raise the cradle to the maximum height.
3. Lift the cradle an additional 1/2" by hand.
4. Tighten the cradle lock.
5. Loosen the socket head screw and remove the
meter box.
6. Remove the meter box stud from the cradle.
7. Remove the screw and washer from the end of
the pinion shaft.
8. Remove the handle and pinion shaft assembly.
9. Turn the assembly around 180° and insert into
cradle.
10. Replace the screw and washer and tighten se-
curely.
11. Replace the meter stud on the side opposite the
handle.
Socket
screw
Ammeter
gauge
Meter
box
Cradle
lock
Socket screw
and washer
Socket
Ammeter
screw
gauge
Meter
box
12. Attach meter box to opposite side (see "Mounting
the Meter Box").
13. Loosen the cradle lock and lower the cradle until
the pinion engages the rack.
14. Tighten the cradle lock.
Mounting the Meter Box
For All Catalog Nos.
A meter box is standard equipment with the Vac-U-
Rig , but it must be purchased separately for other
®
Dymorigs (see "Accessories"). Attach the meter box
to the cradle on the side opposite of the handle.
1. Slip the collar on the meter box over the stud on
the cradle.
2. Position the meter box as desired and tighten the
1/4"-20 threaded socket head screw.
NOTE: For horizontal (wall) coring, the ammeter
gauge must face upward in view of the operator.
Otherwise, water flow from the water shut-off valve
might drip into the outlets on the meter box.
Mounting the Dymodrill Motor to the Stand
For All Cat. Nos.
Dymorigs include a mounting bracket which mounts
Dymodrill motors to the stand. An optional spacer
assembly is available (see "Accessories"), which
can be used when coring with any bits; but it must
be used with any bit over 10" (outside diameter).
1. To mount the motor, loosen the cradle lock. Raise
the cradle on the column using the spoked handle
to allow room for installing the bit later. Tighten the
cradle lock.
NOTE: If the cradle is difficult to move on the
column, loosen the gib screws (see "Adjusting the
Gib Screws").
2. Fasten the mounting
bracket or the op-
tional spacer as-
sembly to the Dy-
modrill motor using
the four (4) 1/4"-20
threaded socket
head screws and
four (4) lock wash-
ers (they are the
smaller of the two
provided in sepa-
r a t e a c c e s s o r y
bag). Make sure
the square key on the mounting bracket or spacer
assembly engages with the slot on the Dymodrill
motor.
3. Fasten the mounting bracket
(or optional spacer assembly)
and motor assembly to the
cradle slot by inserting the
four (4) 3/8"-16 threaded
socket head cap screws and
lock washers (they are the
larger of the two provided in separate accessory
bag) through the cradle. Place screws through the
holes from the other side of the Dymorig and place
lock washers on the side of the mounting bracket.
After the Dymodrill motor is mounted, make sure the
cradle is rigid against the column to prevent the motor
or bit from wobbling during coring. Before coring, try
to wiggle the cradle and motor with your hands. If the
cradle is secure, it should not move. If it does move,
tighten the gib screws that secure the cradle to the
column (see "Adjusting the Gib Screws").
6
Slot