Page 7
Descrizione Uscita Tamper Contatto NC I walk test permettono la regolazione dell’area di ri- PXDTVE è un sensore a doppia tecnologia (infrarosso Temperatura d’esercizio [°C] -40 / +50 levazione del sensore. Le regolazioni di infrarosso e passivo e microonda), filare, da esterno. L’allarme vie-...
Page 8
A questo punto il sensore è pronto per ‘l’inizializzazio- Regolazione dell’infrarosso 6 JP2: Abilitazione/Disabilitazione Tamper anti- ne’ che durerà 5 secondi. 1- Impostare il DIP7 a seconda della della dimensione strappo Inizializzazione dell’area da proteggere; JP2 APERTO: tamper JP2 CHIUSO: tamper di- abilitato sabilitato Alimentando il sensore, si accenderanno in modo fis-...
Page 9
2- Regolare il sensore microonda muovendosi all’in- te solo dopo la fase di stabilizzazione dall’accensione; Q1 e che il coprilente rimanga ben saldo alla testina terno dell’area di rilevazione: il LED blu si accenderà durante questa fase non sostare o muoversi entro l’a- quando la microonda rileverà...
Page 10
Walk test MW operation (DL2 on steady, Working temperature (°C) -40 / +50 DL3 indicates the detection) PXDTVE is a wired dual technology sensor (PIR and mi- Dimensions (mm) 190x85x75 crowave) for outdoor use. The alarm is only generated The walk tests allows adjustment of the sensor de-...
Page 11
ing that initialisation has been successful. If anything is 2- Set DIP5 to ON and DIP6 to OFF to enable the walk 6 JP2: Enabling/Disabling Tear-Resistant Tamper detected during this phase, the initialisation time will test for the infrared only. The DL1 LED (infrared) will OPEN: tamper JP2 CLOSED: tamper...
(for example by moving leaves) and the microwave of 1° of the head corresponds to the movements of This product complies with the law. detecting beyond the desired area (for example a the beams of around 30 cm at 18 m). Never point the Decommissioning and disposal.
Page 13
Sortie Autoprotection Contact NF (DL2 allumé en permanence, DL3 signa- Température de fonctionnement (°C) -40 / +50 PXDTVE est un capteur filaire d’extérieur à double tech- le la détection) nologie (infrarouge passif et micro-onde). Dimensions (mm) 190x85x75 Les essais de marche permettent le réglage de la zone L’alarme est générée uniquement si les technologies...
Page 14
Cavaliers - Dip1, Dip2, Dip5, Dip6 sur OFF, Dip3 et Dip4 sur gies (infrarouge C1 et micro-onde C2) détectent. ON et Dip7 au choix 4 ; Il faut par conséquent régler aussi bien l’ORIENTATION E JP1 : Activation/Désactivation Autoprotection an- - JP1 ouvert E, JP2 6 et JP3 fermés G.
tiver l’essai de marche uniquement sur la micro-onde. et RV2) dans le sens horaire et orienter les têtes le L’emballage du capteur comprend également un Le VOYANT DL2 (micro-onde) s’allumera en perma- plus possible vers le bas. Réduire progressivement la couvre-lentille en plastique à...
Page 16
[м]* Описание сигнализирует о работе детектора). Н.З. контак- ON Работа в режиме "Тестирование" СВЧ-де- PXDTVE ― проводной комбинированный (ПИК + СВЧ) Выход "ТРЕВОЖНАЯ СИГНАЛИЗАЦИЯ" ты Optomos тектора (DL2 горит ровным светом, DL3 датчик для наружной установки. Тревожная сиг- Выход датчика вскрытия...
Page 17
Перемычки - установить переключатели Dip1, Dip2, Dip5, Dip6 мо правильно РАСПОЛОЖИТЬ и отрегулировать ДАЛЬ- в положение «ВЫКЛ.», Dip3 и Dip4 — в положение НОСТЬ каждого детектора для того, чтобы их зоны E JP1: включение/выключение датчика вскрытия. «ВКЛ.» и выбрать положение Dip7 4; обнаружения...
Page 18
специальным символом с обозначением материала. Частичное затемнение ИК-детектора раженная в метрах) рассчитана с учетом тепла чело- КОМПАНИЯ CAME S.P.A. СОХРАНЯЕТ ЗА СОБОЙ ПРАВО НА ИЗМЕ- НЕНИЕ СОДЕРЖАЩЕЙСЯ В ЭТОЙ ИНСТРУКЦИИ ИНФОРМАЦИИ В веческого тела, и следовательно, является ОТНОСИ- В случае большой протяженности зоны обнаружения и...
Page 20
Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c 31030 Dosson di Casier 33079 Sesto al Reghena Treviso - Italy Pordenone - Italy (+39) 0422 4940 (+39) 0434 698111 (+39) 0422 4941 (+39) 0434 698434 www.came.com...
Need help?
Do you have a question about the PXDTVE and is the answer not in the manual?
Questions and answers