Advertisement
PLEASE READ THESE INSTRUCTIONS
FIRST BEFORE INSTALLATION
Congratulations on the purchase of your new Nanolux DE FIXTURE 1000W
and 600W luminaire. We have done everything to insure a long life and safe
operations, but the installations and use of the ballast is the responsibility of
the user. Incorrect use or installations can lead to failure and damage to the
ballast. Damage to the luminaire and electronic circuitry as a result of
incorrect installations and use revokes your warranty. Read this manual
carefully before installing your luminaire.
TECHNICAL SPECIFICATIONS
1000W
Model
No Fan
Fan
Input Voltage
208VAC-240VAC 120VAC-240VAC 208VAC-240VAC 120VAC/240VAC
Output Voltage
200V-300V
Input Frequency
50-60Hz
Output Power
1200W Max
Power Factor
≥0.99
Crest Factor
＜1.7
THD
≤10%
600W-660W-750W-825W-1000W
Dimming
-1200W
Strike Lamp
Double Ended Lamp
Over Temperature Protection; Over/Under Voltage Protection;
Protection
Function
Open/Short Circuit Protection;
670*301*115mm
670*330*115mm
670*240*115mm
Size
26.4*11.8*4.5 inch
26.4*13*4.5 inch
26.4*9.4*4.5 inch
(L*W*H)
5.54 kgs
5.88 kgs
Weight
12.21 lbs
12.96 lbs
PRODUCT DESCRIPTION
The Nanolux DE FIXTURE 1000W and 600W are state of the art adjustable
horticultural quality luminaire. They are designed to drive the 1000W and
600W Double Ended electronic high frequency HPS lamps. Professional
electronic HPS lamps operate at very high frequency to prevent acoustic
resonance and to optimize lamp life.The NCCS system is also incorporated.
The fanless luminaire housing is sealed. The housing allows warm air to exit
the housing, cool air to enter the housing when cooling down while
preventing dust and moisture to enter.
a-1
b-1
a-3
b-3
b-1
a-1
b
-01-
HOW TO INSTALL LAMP HOLDER
ON BALLAST
The Nanolux DE fixture ballasts are designed to drive horticultural high
600W
frequency HPS lamps for plant cultivation. They are intended for climate
No Fan
Fan
room use. They are suited for a damp location but should not be used
outdoors or in wet environments.
80V-150V
High Intensity Discharge lamps generate intense heat. Installations of HID
50-60Hz
lamps should follow local installation and safety regulations.
600W Max
≥0.99
＜1.7
≤10%
300W-450W-600W
-Super-Lux
Double Ended Lamp
670*270*115mm
26.4*10.6*4.5 inch
4.62 kgs
4.95 kgs
10.2 lbs
10.91 lbs
b
a-2
b-2
a
b-2
a-2
b-3
a-3
d
c
a
c
-02-
HOT RESTRIKE
C A U T I O N :
• Always install the lamp before connecting your luminaire to mains.
• Allow lamp to cool 30 minutes before restarting (hot restrike).
• When changing the lamp always disconnect the luminaire from mains
by removing the mains plug. Let the lamp and reflector cool down for
30 minutes before changing as they are very hot. When replacing a
defect lamp without disconnecting mains the lamp will not start.
Disconnecting the power will restart the ballast.
• DO NOT touch hot Ceramic socket.
• Make sure the DE lamp wires are correctly within the socket copper
wire clamps.
• Make sure to fully close the ceramic socket to the correct position and
keep the socket clean to provide proper function.
• Fragile !! Be careful and do not exert excessive force while moving the
ceramic slider on the ceramic socket connection
• Keep away from water.
LAMP REPLACEMENT
TO TAKE OUT A LAMP:
• DISCONNECT THE MAINS FIRST
• Open the lamp holders by sliding them outward. The lamp is held by a
metal spring at each side, though it is recommended to hold the lamp
while opening the lamp holders to prevent the lamp from falling.
TO INSTALL A NEW LAMP:
• DISCONNECT FROM MAINS FIRST
• Make sure the lamp is clean, wear cotton gloves and clean the lamp
after installation with a dry soft cloth. Never use detergents to clean
a lamp, use pure alcohol or whip clean with a dry clean soft cloth.
• Make sure the end wires are straight.
• Open the lamp holders by sliding them outward. Press the lamp in the
fitting until the metal springs hold the lamp, with the glass vacuum
seal pointed downward.
• Close the lamp holders by sliding them inward.
• Wipe the lamp with a clean soft cloth.
• Be sure not to touch the reflective material of the reflector with your
bare hands.
-03-
HOT
a
b
Advertisement
