Princess auto Drift hero Assembly Instructions Manual

Hide thumbs Also See for Drift hero:

Advertisement

ASSEMLBY INSTRUCTIONS
CAUTION
NEVER ATTEMPT TO START THIS MINI BIKE WITHOUT
READING AND UNDERSTANDING THE OWNER'S MANUAL.
THE OWNER'S MANUAL PROVIDES INFORMATION ON
SAFETY, PARTS, FUNCTIONS, PRE-RIDE INSPECTION,
STARTING AND MAINTENANCE.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Drift hero and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Princess auto Drift hero

  • Page 1 ASSEMLBY INSTRUCTIONS CAUTION NEVER ATTEMPT TO START THIS MINI BIKE WITHOUT READING AND UNDERSTANDING THE OWNER’S MANUAL. THE OWNER’S MANUAL PROVIDES INFORMATION ON SAFETY, PARTS, FUNCTIONS, PRE-RIDE INSPECTION, STARTING AND MAINTENANCE.
  • Page 2: Removal From Crate

    REMOVAL FROM CRATE M10 STEERING BOLT RONT FORK ASSEMBLY 10mm WASKERS HARDWARE M10 SELF-LOCK NUT FRONT FENDER M6*20 BOLT FRONT RENDER ASSEMBLY M6 NUTS 6mm WASHERS ZIP TIES OF CABLES ZIP TIES ENGINE MOUNT M8*20 BOLT BOLT CLUTCH COVER M8*20 BOLT BOLT...
  • Page 3 FRONT WHEEL M12 AXLE BOLT FRONT WHEEL ASSEMBLY M12 SELF-LOCK NUT WHEEL BUSHING NUMBER PLATE FRONT PLATE ASSEMBLY M6*20 BOLT CLUTCH 12 TEETH CLUTCH BUSHING CLUTCH 12 TEETH ASSEMBLY 6mm WASHER M1/4-28*4/3 BOLT...
  • Page 4: Engine Installation

    ENGINE INSTALLATION 1\INSTALL THE CLUTCH TO ENGINE SHAFT. PUT THE PARTS LIKE THE FOLLOWING ORDER: CLUTCH BUSHING (16*20*3mm), CLUTCH 12 TEETH, WASHER(6*25*3mm), M1/4-28*4/3 BOLT. Clutch Bushing 2\TIGHTEN THE CLUTCH BOLT: TROUQE 69-104in.lbs Clutch 12 Teeth Washer and Spring washer M1/4-28*4/3 Bolt 3\ PUT THE ENINGE ON TO THE FARME, USE THE ENGINE MOUNT BOLTS (M8*20 BOLT) TO KEEP THE ENGINE ON POSITION.
  • Page 5: Front Fork Installation

    FRONT FORK INSTALLATION M10 Steering bolt 1\ INSTALL FRONT FORK ASSEMBLY BY 10mm Washer INSERTINGTHE M10 STEERING BOLT THROUGH THE ASSEMBLY IN THE FOLLOWING ORDER: TOP BRACKET, 10mm WASHER, STEERING NECK, 10mm WASHER, BOTTOM BRACKET, Steering Neck M10 SELF-LOCK NUT. 2\ TIGHTEN THE M10 SELF-LOCK NUT: TROUQE 22-29ft.
  • Page 6: Front Fender Installation

    FRONT FENDER INSTALLATION 1\ ATTACH THE FRONT FENDER WITH M6*16 BOLTS, 6mm WASHERS AND 6mm NUTS. 2\TIGHTEN THE M6 SELF-LOCK NUT: TROUQE 69-104in.lbs NOTE: SMALL PORTION OF FENDER FACE FORWARD. CAUTION: ALL THE PARTS ARE PUT IN THE Tighten the M6 nuts PAG WITH THE LABEL “FRONT FENDER ASSEMBLY”.
  • Page 7: Front Wheel Installation

    FRONT WHEEL INSTALLATION 1\ ORIENT THE FRONT TIRE SO THE ARROW Arrow Faces Forward ON THE TIRE SIDE FACE FORWARD. 2\INSERT AXLE BOLT WITH THE WHEEL BUSHINGS BETWEEN THE FORKS AND WHEEL ASSEMBLY ON ENACH SIDE. 3\ INSTALL THE M12 SELF-LOCK NUT AND TIGHTEN.
  • Page 8 SECURE WIRES AND CABLES 1\ MOUNT THE THROTTLE CABLE TO THE ENGINE THROTTLE BRACKET AND CONECT SWITCH OFF WIRE WITH THE ENGINE WIRE. 2\MAKE SURE THE ON/OFF SWITCH WIRE, THROTTLE CABLE AND BRAKE CABLE ARE NOT KINKED AND HAVE FREE MOVEMENT WHEN THE HANDLE BAR ARE TRUNED FROM LEFT TO RIGHT.
  • Page 9: Oil And Fuel

    OIL AND FUEL Engine Oil Mini bike DOES NOT have oil in crankcase when shipped from the factory. NEVER ATTEMPT to start the engine without engine oil. Filling with Oil 1. Remove the oil fill plug (1) 2. fill with SAE 10W-30 motor oil. This mini bike takes .63qt.
  • Page 10: Tire Pressure

    TIRE PRESSURE Tires 1. Check tire pressure. Incorrect tire pressure can affect the handling, rider comfort, steering, tire life and traction. Always check the tire pres- sure before each ride. Tire pressure Front tires: 5psi Rear tires: 5psi 1/2 - 3/4 in. (15-20mm) Chain tension Check the tension of the chain , The...
  • Page 11: Brake Adjustment

    BRAKE ADJUSTMENT Brakes 2.0 - 4.0mm Brake Lever Adjustment (0.08 - 0.16 in) The front left brake lever (1) should have 2.0 - 4.0mm (0.08 - 0.16) of free play. To adjust brake lever free play: 1. Loosen the jam nut (2) on the brake cable.
  • Page 12: Throttle Adjustment

    THROTTLE ADJUSTMENT Throttle Cable adjustment It is important that the throttle grip have a certain amount of free play . The hand grip throttle free play (2) should .078 - .24 in be .078 - .24 in (2-6 mm) (2-6 mm) To adjust freeplay 1.
  • Page 13 PRE-RIDE INSPECTION Inspecting and checking the condition of the Mini Bike before each ride is important. Following WHAT TO CHECK FOR the pre-ride check list will help CHECK insure there are no problems which Steering • Smoothness could result in injury or becoming •...
  • Page 14: Starting Engine

    STARTING ENGINE STARTING ENGINE To start the engine 1. Place the fuel valve (1) in the “ON” (vertical) position. 2.. If engine is cold, place the choke lever (2) in the “ON” (right position. 3. Place the ON/OFF switch (3), located on the handlebars, in the (on)position.

Table of Contents