Full Gauge Controls TCP-485 WiFi Log Instruction Manual

Have this manual in the palm
of your hand through the FG Finder app.
BEFORE INSTALLING THE CONTROLLER, WE RECOMMEND THAT YOU READ THE INSTRUCTION MANUAL
COMPLETELY IN ORDER TO AVOID POSSIBLE DAMAGE TO THE PRODUCT.
PRODUCT INSTALLATION PRECAUTION:
- Before performing any procedure on this instrument, disconnect it from the power supply;
- Ensure that the instrument has proper ventilation, avoiding installing it on panels that contain other devices that can
cause it to operate outside the specified temperature limits;
- Install the product away from sources that may generate electromagnetic disturbances, such as: enginees, contactors,
relays, solenoids, etc.
AUTHORIZED SERVICE:
- The installation and maintenance of the product must be performed only by qualified personnel;
ACCESSORIES:
- Use only original Full Gauge Controls accessories.
- If in doubt, contact technical support.
AS IT IS CONSTANTLY EVOLVING, FULL GAUGE CONTROLS RESERVES THE RIGHT TO CHANGE THE INFORMATION
CONTAINED IN THE MANUAL AT ANY TIME, WITHOUT PRIOR NOTICE.
"Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e
"This equipment is not entitled to protection against harmful interference and must not cause interference in duly
atende aos requisitos técnicos aplicados".
authorized systems."
"Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de
"This product is not suitable for use in a domestic environment, as it may cause electromagnetic interference that requires
estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário".
the user to take necessary measures to minimize these interference"
1. DESCRIPTION
The TCP-485 WiFi Log converter is an interface for communicating Full Gauge Controls controllers with the
management software. The TCP-485 WiFi Log uses a Wi-Fi or Ethernet data network to
Pro
Sitrad
communicate with the TCP/IP standard. Currently, many companies have wireless routers installed in their facilities,
as well as wired infrastructures, making it possible to use these same networks for data traffic between controllers
, using the TCP-485 WiFi Log converter.
Pro
and Sitrad
This equipment has internal memory for data storage (datalogger), with the specific purpose of storing controller
Pro
logs when communication with Sitrad is unavailable.
Through the smartphone configuration app or Sitrad
registered and what is their periodicity. The logs registered in the equipment can be requested by
the communication is reestablished, allowing its insertion in the supervisory database.
2. APPLICATIONS
- Installations in which using the existing Wireless or Ethernet network is paramount;
- Installations that do not have conditions for passing new RS-485 data cabling and already have and Ethernet
structure installed.
Note: The TCP-485 WiFi Log converter is designed to work with Full Gauge Controls instrument only.
3. TECHNICAL SPECIFICATIONS
Converter power
Power supply included with
the converter
Operating Temperature
Operating Humidity
Number of instruments supported per
converter on an RS-485 network
Wi-Fi antenna
Wi-Fi compatibility
Wi-Fi frequency
Encryption type
Ethernet (Lan Port)
Internal memory
Product dimensions (without antenna)
Antenna dimensions
4. DIMENSIONS
12,8mm
164,8 mm
Antenna
TCP-485 WiFi Log
SERIAL / WI-FI CONVERTER WITH DATALOGGER
Wi-Fi Supervisory
system
WARNING
ANATEL
Pro
, it is possible to select which instruments will have their logs
External 5.1
Input - 100-240 Vac (50/60Hz)
Output: 5.1Vdc / 2A
0 to 50ºC / 32 to 122ºF
10 to 90% UR (without condensation)
32 (without the need for termination)
3,8dBi for stable, high-quality connection
IEEE 802.11 b/g/n up to 72,2 Mbps
2,4GHz band, channels 1 to 11
WEP, WPA and WPA2
93,6 x 37,1 x 91,1 mm (WxHxD)
194,5 x 12,8mm (LxD)
85,7mm
93,6mm
90°
17,75mm
29,7mm
Frontal view
RS
LOG
485
Ethernet Serial Datalogger
Comunication
5. INDICATIONS AND KEYS
1. POWER LED - Indication of power and operating mode
2. STATUS LED - Indication of the connection status and signal strength
3. TX LED - Indicates transmission over the RS-485 network
4. RX LED - Indicates reception over the the RS-485 network
5. DIN rail lock
6. Power connector
7. RS-485 network connector
8. RJ-45 connector for ethenet cable
9. RESET button - Switch between operating modes, or restore to factory default
10
settings
10. Wi-Fi antenna
9
1
2
3
4 5
6. INSTALLATION
Pro
Sitrad as soon as
The TCP-485 WiFi Log converter should be preferably installed in places away from noise and
electromagnetic interference. It must be powered by the power supply provided with the device, if provided,
or a compatible one.
If the operating mode is Wi-Fi Client, the signal quality of the wireless network must be ensured. If the signal
is bad or very bad (see item 9), the communication may become unstable and there may be loss of
information. For recommendations on how to position the device to avoid interference, see item 13.
The RS-485 network must be connected following the recommendations in item 12.
7. OPERATION MODES
The TCP-485 WiFi Log converter has two network interfaces: Ethernet and Wi-Fi, and three modes
Vdc / A source 2
of operation: Wi-Fi Access Point, Wi-Fi Client and Ethernet Client. Only one operation mode is enabled at a
time that is, it is not possible to use the Ethernet and Wi-Fi interfaces at the same time.
7.1 Wi-Fi Access Point Mode:
In this mode, it operates as a Wi-Fi access point that accepts connection from only one client. This is the
factory default operating mode, which basically serves to configure the converter on first use, although it can
operate in this mode with a Sitrad client connected to it. The factory default SSID is TCP-485 WIFI Log W-
XXXX E-YYYY, with XXXX being the last 4 digits of the Wi-Fi MAC address and YYYY being the last 4 digits
of the Ethernet MAC address.
Wi-Fi: F8: F0: 05: AD: 75: 56
Example:
Ethernet: F8: F0: 05: AD: 10: 54
The MAC address of the product's network interfaces can be found on the label located on the front of the
case.
10 / 100 Mbps
8MB
7.2 Wi-Fi Client Mode
In this mode, it operates as a Wi-Fi client and connects to the wireless network provided by the user.
Supports dynamic (DHCP) or static IP configuration. It accepts the connection of a Sitrad client and has an
IP filter to restrict access within the network.
7.3
Ethernet Client Mode
In this mode, it operates as an Ethernet client and connects to the wired network provided by the user.
Supports dynamic (DHCP) or static IP configuration. It accepts the connection of a Sitrad client and has an
IP filter to restrict access within the network.
91,1mm
Side view
8
6
7
Pro
SSID TCP-485 WiFi Log W7556 - E1054
The default password is admin123
:
:
Pro
Pro