Full Gauge Controls TCP-485 WiFi Log Uick Start Manual

Access this manual in the palm
of your hand with the FG Finder app.
WARNING
BEFORE THE INSTALLATION OF THE CONVERTER, WE RECOMMEND READING THE
INSTRUCTION MANUAL IN FULL TO PREVENT POSSIBLE DAMAGE TO THE PRODUCT.
PRODUCT INSTALLATION PRECAUTIONS:
Before performing any procedure on this instrument, disconnect it from the power grid;
Ensure that it has adequate ventilation, avoiding installation on control panels containing devices
that could cause it to operate outside its specified temperature range;
Install the product away from sources that may generate electromagnetic disturbances, such as:
motors, contactors, relays, electrovalves, etc.;
AUTHORIZED SERVICES:
The installation and maintenance of the product must be performed by qualified personnel only;
ACESSORIES:
Use only Full Gauge Controls original accessories.
If you have any queries, please contact our technical support.
THROUGH CONTINUOUS DEVELOPMENT, FULL GAUGE CONTROLS RESERVES THE RIGHT TO
CHANGE THIS MANUAL INFORMATION AT ANY TIME, WITHOUT PRIOR NOTICE.
'' This product is approved by ANATEL, in accordance with the procedures regulated by Resolution
242/2000, and meets the technical requirements applied.»
'' This equipment operates in secondary character, i.e. it is not entitled to be protected against harmful
interference, even from stations of the same kind, and it cannot cause interference in systems
operating in primary character''.
1. DESCRIPTION
The Serial/WiFi converter TCP-485 WiFi Log allows the interconnection of Full Gauge controllers with the
supervisory software Sitrad through a WiFi data network using the TCP/IP communication standard. Currently,
many companies have Wireless routers in their facilities, making it possible to use the same network to exchange
data between the controllers and the supervisory software Sitrad using the TCP-485 WiFi Log converter.
This device has internal memory for data storage (datalogger), wich, through its page or the supervisory software
Sitrad PRO , allows to select which instruments will perform LOG and what their periodicity, the log occurs only
when the supervisory software is not communicating. Ensuring the missing data is filled in at the supervisory
software's database when communication returns by searching for it in the converter's datalogger.
2. APLICATIONS
• Facilities where it is desirable to use the existing Wireless network;
• Facilities that do not have conditions for fitting new Ethernet data cabling;
• Facilities where the cost of the investment in the cabled structure has an impact;
TCP-485 WiFi Log
Note.: The converter is designed to work with Full Gauge Controls instruments only.
3. TECHNICAL ESPECIFICATIONS
Converter power
Power supply provided with the converter
Operating temperature
Operating humidity
Number of instruments supported per converter
in the RS-485 network
Antenna
Compatibility
Encryption type
Product dimensions
Antenna dimensions
4. INDICATIONS
TCP-485 WiFi Log
ALL MODES
CONFIGURATION
MODE
OPERATION
MODE
TCP-485 WiFi Log
TCP-485 WiFi Log
SERIAL / WiFi CONVERTER
Wi-Fi Supervisory
system
ANATEL
External power 12 Vdc / 1A
Input - 100-240Vac (50/60Hz)
Output: 12Vdc / 2A
0 to 50ºC / 32 a 122ºF
10 to 90% UR (without condensation)
32 (without the need for termination)
3,8dBi for a estable high quality connection
IEEE 802.11 b/g up to 54 Mbps
WEP, WPA and WAP2
43,5 x 16 x 34 mm (WxHxD)
34,9 x 175,2 x 13 mm (WxHxD)
LED STATUS / Status
White / On
White / Flashing
Yellow / Flashing
Red / Flashing
Green / Flashing
Yellow / Flashing
Yellow / On
Blue / Flashing
Blue / Flashing
Blue / Flashing
Blue / Flashing
Blue / Flashing
Blue / On
LED TX
Green / On
RS
LOG LOG
485
Serial Datalogger
Comunication
5. INDICATIONS AND KEY
Power indication LED -
P o w e r a n d s i g n a l
strength indication LED
R S - 4 8 5 n e t w o r k
t r a n s m i s s i o n
indication LED
R S - 4 8 5 n e t w o r k
reception indication
LED
S t a t u s L E D -
Connection status
indication LED.
LED POWER / Status
White / On
White / Flashing
Yellow / Flashing
Red / Flashing
Red / On
Red / On
TCP-485 WiFi Log connected and ready to be configured via internet browser
Red / On
Green / On
Yellow / On
Purple / On
Purple / Flashing
Red / Flashing
Red / On
LED RX
Green / On
Antenna - Connect the antenna supplied
with the converter.
NOTE: Only use the antenna provided by
Full Gauge
Converter power
Reset - see item 7 - Reset configuration
Communication network with RS-485 instruments
Occurrence
TCP-485 WiFi Log booting
Contact Full Gauge Controls
Contact Full Gauge Controls
Router connection password error
TCP-485 WiFi Log scanning the network
TCP-485 WiFi Log ready to connect
Excellent signal level
Good signal level
Poor signal level
Very poor signal level
No signal
Connected with Sitrad and communicating
Ocurrence
Unconfigured clock