Table of Contents
Advertisement
Quick Links
Model 2AM Shown
Thank you for purchasing this Gast product. It is manufactured to the highest standards
using quality materials. This manual includes general safety instructions for operation under normal conditions
and for operation in hazardous conditions. Please follow all recommended maintenance, operational and safety
PLEASE READ THIS MANUAL COMPLETELY BEFORE INSTALLING AND USING
Operating Pressure Limits
Lubricated Models
1AM
1UP
2AM
4AM
6AM
8AM
16AM
• Non-hazardous conditions: Operate at ambient temperatures up
to 250ºF (121ºC).
• Hazardous conditions: Operate at ambient temperatures up to
104ºF (40ºC).
• Protect unit from dirt and moisture.
• Use ONLY compressed air to drive motor.
• Air lines connected to motor should be the same size or the next
size larger than the inlet port for efficient output and speed con-
trol.
• Protect all surrounding items from exhaust air.
• Bearings are grease packed.
® Registered Trademark/™ Trademark of Gast Manufacturing Inc. ©Copyright 2019 Gast Manufacturing Inc. All Rights Reserved.
AM SERIES AIR MOTORS
Operation and Maintenance Manual
Model 4AM Shown
instructions and you will receive years of trouble-free service.
THIS PRODUCT. SAVE THIS MANUAL FOR FUTURE REFERENCE AND
KEEP IN THE VICINITY OF THE PRODUCT.
Pressure
100 psi / 7 bar
80 psi / 5.6 bar
100 psi / 7 bar
100 psi / 7 bar
100 psi / 7 bar
100 psi / 7 bar
100 psi / 7 bar
Part No. 45-200 D170 (Rev. T)
Model 6AM Shown
WARNING
LL and NLP Models
Pressure
1AM
80 psi / 5.5 bar
1UP
65 psi / 4.9 bar
2AM
80 psi / 5.5 bar
4AM
80 psi / 5.5 bar
6AM
80 psi / 5.5 bar
8AM
80 psi / 5.5 bar
16AM
80 psi / 5.5 bar
• Use Gast #AD220 or a detergent SAE#10 automotive engine oil
for lubricating.
• Motors are to be used in commercial installations only.
•
This symbol appears on labels of air motors that
are designed for use in hazardous atmospheres. These
air motors comply with the applicable standards and
specifications and meet the requirements of the guidelines
of the Directive 2014/34/EU. They are intended to be used
in zones 1 and 2 where explosive atmospheres are likely to
occur.
• Air supply, directional control valve and pressure regulator should
be selected based upon the air consumption of the motor.
Model 16AM Shown
www.gastmfg.com
ISO 9001 CERTIFIED
Advertisement
Table of Contents
Related Manuals for Idex GAST AM Series
Summary of Contents for Idex GAST AM Series
- Page 1 Part No. 45-200 D170 (Rev. T) AM SERIES AIR MOTORS Operation and Maintenance Manual Model 2AM Shown Model 4AM Shown Model 6AM Shown Model 16AM Shown Thank you for purchasing this Gast product. It is manufactured to the highest standards using quality materials.
- Page 2 Your safety and the safety of others is extremely important. Complete the following checklist prior to starting installation in a hazardous area. All actions must be We have provided many important safety messages in this completed in accordance with Directive 2014/34/EU. manual and on your product.
- Page 3 Mounting Do not use a hammer on the shaft or connections. This product can be installed in any orientation. Mount the motor to a solid metal base plate that is mounted to a stable, rigid operating surface. Use shock mounts to reduce noise and vibration. Install a Lubricating the drive shaft will make assembly pressure regulator or simple shut-off valve to control motor.
- Page 4 Use only Gast #AH255B Flushing Solvent. DO NOT use Operate the motor for approximately 2 hours at kerosene or ANY other combustible solvents to flush this the maximum desired load. Measure the surface product. temperature of the motor on the casting opposite the pipe ports.
- Page 5 Estimated Ball Bearing Life of Air Motors Air Model Model Shaft Speed in RP Ball Bearing Life Hours L 10,000 28,000 6,000 14,000 3,000 30,000 3,000 14,000 3,000 6,500 2,000 8,000 16AM 2,000 15,000 Based on running pressure of 60 PSI and coupling connection to motor load. The direction, magnitude and location of applied loads to the motor shaft will change expected bearing life.
- Page 6 Worm Gear Reducer Series A-F Change output shaft direction of worm gear reducers Gear Reducer Specifications Remove drain plug and drain oil from unit. All output shafts are in the standard location. Remove end cover and seal cage cap screws. While supporting Model Air Motor Ratio...
- Page 7 WARRANTY Gast finished products, when properly installed and operated under normal conditions of use, are warranted by Gast to be free from defects in material and workmanship for a period of twelve (12) months from the date of purchase from Gast or an authorized Gast Representative or Distributor.
- Page 8 MAINTENANCE RECORD Date Procedure Performed For repair parts ordering information and exploded product view, visit our website or call us at the number listed below. We have Gast Authorized Repair Facilities throughout the world. For the most up-to-date listing, contact one of our sales offices below: Gast Manufacturing Gast Group Limited...
Need help?
Do you have a question about the GAST AM Series and is the answer not in the manual?
Questions and answers