Summary The CAME-TV WAERO Duplex Digital Wireless Foldable Headset is easy to set up and provides about 350m/1200ft of open range between the Master and Remote headsets. There are two versions available, US for the US while EU for EU...
Page 3
Operating Instructions 1.Power On/Off Power on: the headset will be powered on automatically when battery is installed. In the condition that battery is already in its compartment, one quick press the power button to turn on the headset. Power off: Press and hold the power button for around 5 seconds until power indicator changes off.
Page 4
microphone only and you can still hear what everyone else is saying. 4. Volume Voice +: Raise the volume Voice -: Lower the volume 5. Pairing Headsets are paired at the factory and ready for use when they are powered on. For the headsets which already had been paired successfully, they can be connected automatically and no need to pair again.
Page 5
Then following steps should be proceed on the premise of that the led on the remote headset become solid after powered on. On the remote headset, press and hold on both volume + & - buttons simultaneously until the Blue LED starts flashing quickly.
Page 6
Quick Start and Tips How to quit pairing Pair How to Pair process Short press Power Press and hold button on master on volume + & - ( Remote will quit Master buttons pairing automatically simultaneously and led indicator until the Red become solid if master Remote Led indicator...
Page 7
1.During pair process, master will always remain in pairing mode while remote needs to be paired one by one. 2.The master headset is not allowed to be in pairing mode if there are more than 2 master headsets. For example, Module one and Module two of the hub can not be in pairing mode at the same time.
Page 8
HUB Description For our standard kits, the most connections available is a four headset connection via a master headset with three remotes. To expand beyond that capability, we now offer a hub to provide connection up to 10 in one system. Normally a master headset can connect to three remotes, but in this configuration the hub is utilizing on of the three channels available to the master.
Page 12
9 Person Team, Max Distance 3600ft Master...
Page 13
From the observation of above diagram, each remote headset can be replaced with the hub to increase the number of the remote headsets and extend the working distance. How to Optimize the Communication Effect: 1. In order to get the best communication result, it is recommended to place the master (or HUB) in the center position, and the remotes are arranged around the master (or...
Page 14
See details in above picture: 1.Functional Button for Master Module 1 2.Functional Button for Remote Module 3.Functional Button for Master Module 2 4.Left Charging Indicator 5.Indicator for Remote Module 6.Right Charging Indicator 7.Indicators for Master Module 1 (It comes with 3 different indicators, from right to left numbered as 1,2,3 respectively.) 8.Power Indicator...
Page 15
9: Indicators for Master Module 2 (It comes with 3 different indicators, from right to left numbered as 1,2,3 respectively.) Hub can be charged with either one battery or two batteries. The built-in board will allocate the battery portion to the proper parts automatically. The hub can also be powered by standard 5V USB devices.
Page 16
2.Press and hold the Volume + & - buttons at the same time on the master headset to activate pairing mode. Then perform a long press on #2 functional button of remote module on the Hub until the indicators flash quickly. Once the indicator becomes solid, this means that the pairing process is completed, and the Remote modular on Hub is now paired with the master...
Page 17
headsets. After three remote headsets are paired with hub master module 1, all led indicators in remote headsets and master module 1 will become solid. If only two remote headsets are needed, long press master module 1 button to quit pairing after two headsets done pairing.
Page 18
HUB Indicators Introduction: One: Indicators on remote modular 1. Flash quickly: Pairing mode 2. Flash slowly: Stand-by mode (It means the headset has already been paired, but has no connection to master, as the master is not turned on.) 3. Solid: Never been paired or working normally. Two: Indicators on master modules 2.1 It comes with 3 different indicators, from left to right numbered as 1,2,3 respectively.
2.4 In working mode, the number of the remote headsets will be the same as the indicators number. And the indicator number is the same as the pairing sequence. Three: Power Charging Indicators When Charging, the battery indicator will flash slowly and become solid when fully charged.
Page 20
received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 21
connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. User must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 22
One Year Warranty Name Phone Email Address Order Number Number Reason of Return...
Need help?
Do you have a question about the WAERO and is the answer not in the manual?
Questions and answers