Steg SDSP 6 Owner's Manual

Digital signal processor

Advertisement

11.TECHNICAL FEATURES
Output power RMS
-
@
4 Ohms
.................................................................
-
@
2 Ohms
.................................................................
Inputs
..........................................................................
Input sensitivity
............................................................
.......................................................................
Outputs
Output voltage RCA / Cinch
.........................................
Frequency response
...................................................
DSP resolution
.............................................................
DSP power
..................................................................
..............................................................
Sampling rate
Signal converters
........................................................
.................................
Signal-to-noise ratio digital input
Signal-to-noise ratio analog input
................................
Distortion(THD)
...........................................................
Damping factor
...........................................................
Input impedance RCA
.................................................
Input impedance highlevel
...........................................
Operating voltage
........................................................
Additional features
......................................................
Dimensions ( W x D x H)
..............................................
D04-MEN082-00
65 Watts per channel (< 1% THD+N)
90 Watts per channel (< 1% THD+N)
2 x RCA / AUX in
6 Highlevel speaker input
1 x Optical SPDIF (12 - 96 kHz)
1 x Remote In
RCA / Cinch 400mv 1 x COAX in
Highlevel 5 - 10 Volts or 10 - 20 Volts
6 x Speaker
2 x RCA / Cinch
1 x Remote Out
> 5 Volts RMS
20 Hz - 22,000 Hz
32 Bit
295 MHz (1.2 billion MAC operations/second)
48 kHz
A/D: Transformation mode
D/A: Transformation mode
105 dB (A-weighted)
100 dB (A-weighted)
< 0.015 %
> 70
22 kOhms
200 Ohms
9 - 15 Volts (max. 5 sec. down to 6 Volts)
Control Input, USB, HEC slot
250 x 210 x 57.5 mm / 11.06 x 8.26 x 2.34"
,
Ower s Manual
Digital Signal Processor
DIGITAL SIGNAL PROCESSOR
SDSP 6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SDSP 6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Steg SDSP 6

  • Page 1 9 - 15 Volts (max. 5 sec. down to 6 Volts) Additional features ............Control Input, USB, HEC slot Dimensions ( W x D x H) ..........250 x 210 x 57.5 mm / 11.06 x 8.26 x 2.34” SDSP 6 DIGITAL SIGNAL PROCESSOR D04-MEN082-00...
  • Page 2: Table Of Contents

    PRODUCT BRIEF INTRODUCTION PRODUCT BRIEF INTRODUCTION INDEX 1.PRODUCT DESCRIPTION-PRECAUTIONARY NOTES The DSP is a digital signal processor essential to maximize the acoustic performance of your car audio system. It consists of a 32-bit DSP processor and 24-bit AD and DA converters. 1.
  • Page 3: Dsp And Drc Installation

    INPUT FUSE FUSE +12V +12V GAIN GAIN GAIN ACC ON ACC ON AUTO ON AUTO ON SDSP 6 249mm REMOTE REMOTE BLUETOOTH BLUETOOTH HIGH LEVEL INPUT HIGH LEVEL INPUT REM + SPEAKER OUT REM + SPEAKER OUT OPTICAL OPTICAL CONTROL...
  • Page 4: Input -Remote Control Outputs And Power Supply

    GAIN GAIN GAIN ACC ON ACC ON AUTO ON AUTO ON SDSP 6 ACC ON ACC ON AUTO ON AUTO ON SDSP 6 USB(type B)connection plug, to connect the processor to a PC and manage its funcitions through the DSP 3 Software. The connection standard is USB 1.1/2.0 compatible.
  • Page 5: Personal Computer And Digital Remote Coontrol(Drc)

    FUSE +12V +12V INPUT INPUT GAIN GAIN GAIN ACC ON ACC ON AUTO ON AUTO ON SDSP 6 REMOTE REMOTE BLUETOOTH BLUETOOTH HIGH LEVEL INPUT HIGH LEVEL INPUT REM + SPEAKER OUT REM + SPEAKER OUT OPTICAL OPTICAL CONTROL CONTROL...
  • Page 6: Software Installation

    1.Insert CD, Double-Click DSP 2.Wait until the process finish 3.Click NEXT 7.GUI OPERATION INSTRUCTION 7.1 Guide to GUI after installation 1. Double - click icon of DSP-CONTROL STEG DSP v1.0.0 4.Click NEXT 5. Set install location 2. DSP connection [ 9 ]...
  • Page 7: Interface Introduction

    PRODUCT BRIEF INTRODUCTION PRODUCT BRIEF INTRODUCTION 3. Enter the GUI you long for! Now you could tone every signal details as experts do 2. FILE MAIN MENU To bring sound effect on your beloved car to a higher level.If the password has been set, 1.
  • Page 8 PRODUCT BRIEF INTRODUCTION PRODUCT BRIEF INTRODUCTION CH mode(click on the default in put state). 4. CROSSOVER X-TPE. optional (2CH 4CH 6CH MIX). To choose different crossover type, for example select CH selection on 3RD spot .that would locate CH you want to choose for crossover configuration . Input channel:FL.
  • Page 9: Stand Installation Reference

    PRODUCT BRIEF INTRODUCTION PRODUCT BRIEF INTRODUCTION 12. X-OVER AND EQ CHARTS. 9. HP/SLOPE. 1.Red lines and slopes will change accordingly when 1.6dB/oct 12dB/oct 18dB/oct 24dB/oct 30dB/oct 36dB/oct. HP/LP of crossover and EQ are modified. 42dB/oct 48dB/oct are available. 2 .EQ all frequency points can be move left or right.For 20Hz-20KHz can be any Regulation. 10.
  • Page 10: Way Crossover Treble Mode

    PRODUCT BRIEF INTRODUCTION PRODUCT BRIEF INTRODUCTION 10.PHONE APP INTRODUCTION 8.2 3 WAY CROSSOVER TREBLE MODE 10.1 Download DSP APP and install it on your phone PM 2:20 PM 2:20 SDSP SDSP APP Source: CD Authority Particulars Version: 1.0.0 Ground Ground Authority Particulars Open Cancel...

Table of Contents