MUST NEVER BE EXCEEDED, as it may damage and/or cause ruptures and/or leakages and/or even break the product, and present a potential hazard and danger to safety, health and/or property. Following are the technical data with respect to the installation of Gessi plumbing products. ► W orkingpressureshouldnotbelowerthan0,5bar(7,25psi)andnotbehigherthan5bar(72Psi).In case of higher working pressure use a pressure reducer valve.
Page 3
Ci-dessous nous indiquons les données techniques concernant l’installation des produits sanitaires Gessi. ► L apressiondeservicenedoitpasêtreinférieureà0,5bar(7,25psi)etsupérieureà5bar(72Psi).En cas de pressions de service plus hautes utiliser une soupape de réduction de la pression.
Page 4
1 - ¡CUIDADO!! LES ROGAMOS QUE TENGAN EN CUENTA QUE NUNCA la presión y/o la temperatura máximaaconsejadaNOTIENEQUESERSUPERADA,yaquepodríadañary/ocausarrupturasy/o pérdidasy/oaveríasdelproductoy,porlotanto,representarunriesgoyunpeligropotencialparala seguridad, la saludad y/o la propiedad. A continuación Les proporcionamos los datos técnicos relativos alainstalacióndelosproductosdegriferíaGessi. ► L apresióndeejercicionotienequeserinferiora0,5bar(7,25psi)ysuperiora5bar(72Psi).Encaso depresionesdeejerciciomayores,utilicenunaválvuladereduccióndelapresión. ►Presiónmáximadeensayodurantelainstalación:8bar(116psi). ► E vitengrandesdiferenciasdepresiónentrelaalimentacióndelaguafríayaquelladelaguacaliente. Lasdiferenciasdepresión,elaguaconunalatocontenidomineralylassustanciasjabonosaspueden...
Page 5
PRE-INSTALLATION INFORMATION - PRÉALABLES - PRELIMINARES Before installation and setting to work Attention! The feeding pipes have to be rinsed thoroughly before the installation of the product, so that no shavings, welding or hemp residual or other dirt can be found in the pipes. Foreign bodies can enter the product through the rinsed pipes or the general water plant and could damage the washers/ring washers.Sofiltersshouldbeinstalledalsoonthegeneralsystem.
INSTALLATION - INSTALLATION - INSTALACIÓN fig. 1 fig. 2 fig. 4 1/2”NPT - M Use hemp or teflon 5/16” Employer chanvre ou teflon [8 mm] Usarcáñamooteflon fig. 3...
Page 8
INSTALLATION - INSTALLATION - INSTALACIÓN insTAllATion fig. 1 - Position the supply pipe so that it does not protrude from the tiled wall. fig. 2 - Tighten the wall connection to the network. Werecommendusinghemptoguaranteetightnesson the threads. fig. 3 - Insert the support for the head on the wall connection. fig.
Page 10
INSTALLATION - INSTALLATION - INSTALACIÓN insTAllATion fig. 5 - Remove the support for the head from the wall. fig. 6 -Piercewitha5/16”D.[8mm]bitinthepreviouslyindicatedpoints. fig. 7 - Introduce plugs as indicated. fig. 8-9 -Insertagainthesupportonthewallconnectionandlockitspositionwithfasteningscrews(check thealignmentofthesupportiscorrectbeforetighteningscrewsfirmly). insTAllATion fig. 5 - Enlever le support pour la pomme du mur. fig.
MAINTENANCE - ENTRETIEN - MANUTENCIÓN ProduCT CleAning Watercontainslimestoneindifferentqualities,whichremainskeptonthesurfacesoftheproduct,leaving deposits after the water has been evaporated. It is possible to prevent the forming of limestone deposits and to keep your product clean by drying it always with a soft cloth immediately after use. DETERGENTS, SOLVENTS, CHEMICAL AGENTS, ABRASIVE SPONGES, WIRE WOOL, ALCOHOL, ETC. SHOULD NOT BE USED as these could irreparably damage products’...
Need help?
Do you have a question about the MIMI 36649 and is the answer not in the manual?
Questions and answers