KitchenAid KDFM404KPS User Manual page 5

OPTIONS
Raises the main wash temperature to improve
cleaning for loads containing tough, baked-on
food.
Dries dishes with heat. This option, with the
use of rinse aid, will provide the best drying
performance. Plastic items are less likely to
deform when loaded in the top rack. Turn the
Heat Dry option off for an air dry.
Sanitizes dishes and glassware in accordance
with NSF International NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have
been designed to meet the requirements of the
NSF/ANSI 184 performance standard for soil
removal and for sanitization efficacy. There is
no intention, either directly or indirectly, that all
cycles on a NSF/ANSI 184 certified dishwasher
meet the NSF/ANSI 184 performance standard
for soil removal and for sanitization efficacy.
The Sani Rinse indicator glows at the end of the
cycle if the Sani Rinse option was successfully
completed. If the indicator does not activate, it
is probably due to the cycle being interrupted.
Runs the dishwasher at a later time or during
off-peak electrical hours. Select a wash cycle
and options. Touch the Delay keypad. Touch
START/RESUME. Close the door firmly.
NOTE: Anytime the door is opened (such as, to
add a dish), the Start/Resume keypad must be
touched again to resume the delay countdown.
Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during
a cycle.
To turn on Control Lock, touch and hold CONTROL LOCK for 3 seconds. Control Lock light will stay on for a short time,
indicating that it is activated. When the Lock indicator is lit, all keypad selections are disabled. If you touch any keypad
selection while your dishwasher is locked, the light flashes three times. The dishwasher door can still be opened/closed
while the controls are locked.
To turn off Control Lock, touch and hold CONTROL LOCK for 3 seconds. Control Lock light turns off.
CONTROL
To start or resume
a wash cycle.
To cancel a wash
cycle after it has
been started
To turn the
audible tones
on or off.
To indicate the
stauts of the
cycle.
cycle except
PURPOSE
If the door is opened during a cycle or the power is interrupted, the Start/Resume
indicator flashes. Cycle will not resume until the door is closed and Start is touched.
Close the door firmly. Touch and hold CANCEL/DRAIN for 3 seconds. The
dishwasher starts a 2-minute drain (if needed). Let dishwasher drain completely.
Touch and hold HI-TEMP WASH for 3 seconds to turn the audible tones on or
off. Only audible tones for confirming keypad touches can be turned on/off.
Important audible tones, such as indicating a cycle has been interrupted, cannot
be deactivated.
The display will indicate cycle progress such as Washing, Drying, Clean, and
Sanitized. The cycle has completed when the Clean light is lit.
If you select the Sani Rinse option, when the cycle is finished, the Sanitized
indicator glows. If the dishwasher did not properly sanitize your dishes, the
Sanitized indicator flashes at the end of the cycle. This can happen if the cycle is
interrupted or if water could not be heated to required temperature. The light goes
off when you open and close door or touch CANCEL.
5
CAN BE WHAT IT DOES
SELECTED
WITH
ProWash™ Raises the main
wash temperate
Normal
up to 135°F (57°C).
Available
Activates the heating
with any
element at the end of
a wash cycle to speed
Rinse Only
drying times. Heat Dry
defaults to On when
any cycle is selected,
except for Express
Wash and Rinse Only.
ProWash™
Increases the main
wash temperature from
Normal
105°F (41°C) to 140°F
(60°C) and the final
rinse from 140°F (60°C)
to 155°F (68°C).
Available Delays the start
with any of a cycle to the
cycle specified time.
COMMENTS
ADDED TIME ADDED
TO CYCLE WATER
(HR:MIN) GALLONS
(LITERS)
0:00 to 0:30 0 to 3.0
(0 to 11.2)
Heat Dry: 0
0:10 to 0:50
Extended
Heat Dry
(includes Heat
Dry time):
0:40 to 1:20
0:00 to 2:20 1.2 to 6.2
(4.8 to 23.3)
0