IDEAL INDUSTRIES CREE LIGHTNING ZR-RK Series Installation Instructions Manual

When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION
DANGER – RISQUE DE CHOC – COUPER L'ALIMENTATION AVANT L'INSTALLATION
2. WARNING – Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for
installation of the LED upgrade kit. Check for enclosed wiring and components.
ATTENTION - Risque d'incendie ou de choc électrique. Câblage électriques peuvent être endommagés lors du perçage pour
l'installation du kit upgrade LED. Vérifier les fils et composants.
3. WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical
systems. If not qualified, do not attempt installation. Product must be installed in accordance with NEC or your local
electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician.
ATTENTION- Risque d'incendie ou de choc électrique. L'installation du kit upgrade LED exige la connaissance des systèmes
électriques pour luminaires. Si non qualifié, ne tentez pas d'installation. Ce produit doit être installé conformément à NEC ou votre
code électrique local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié.
4. WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings where the input rating of the retrofit kit does not exceed the input
rating of the luminaire.
ATTENTION - Risque d'incendie ou de choc électrique. Installez ce kit seulement dans les luminaires qui ont les caractéristiques
de construction et les dimensions dans les photographies ou les dessins de la page suivante.
5. Only the holes indicated in the photographs or drawings may be made or altered as a result of the kit installation. Do not
leave any other holes open in a wiring enclosure or electrical component.
Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits ou altérés pour l'installation du kit upgrade
LED. Ne laissez aucun trou ouvert dans le compartiment électrique.
6. WARNING – To prevent wiring damage or abrasion, do not expose wires to the edge of sheet metal or any other sharp
objects.
ATTENTION - Pour éviter les dégâts de câblage par l'abrasion, ne pas mettre en contact les fils électriques avec des bords de tôle
ou d'autres objets pointus.
7. CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.
8. The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities
having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical
codes. The installation\ guide does not supersede local or national regulations for electrical installations.
9. Examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to
installation of the retrofit kit.
10. CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.
11. For Emergency Luminaires, to reduce the risk of electric shock, disconnect both standard and emergency power supplies and
converter connector of the emergency driver before servicing.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
LIST OF SUPPLIED COMPONENTS
Kit contains the following parts:
(2) Safety Cables
Door Assembly
(Pre-attached to Door
Body
Assembly Body)
(2) Self Tapping M4
Washer Head Screws
1 of 5
Includes: ZRRK14-SC1, ZRRK22-SC1 and ZRRK24-SC1 Standard and Emergency Luminaries
IMPORTANT SAFEGUARDS
NOTES:
1.
Assembly Brackets (2 pcs)
2.
3.
(4) Self Tapping
Screws
(2) Trim Brackets
1- Relamping Label
Upgrade Kit is for installation in 1x4,
2x2, and 2x4 recessed troffer that are
using NEMA 9/16" or 15/16" T-Bar
ceiling grid.
We recommend a test installation
before final installation due to
variety of troffer styles and ceiling
grid types. During test installation,
determine if lamp holders and
ballast need to be removed.
Minimum internal pan size of existing
pan is:
• 1' x 4' - 48.00" (1219 mm) by
12.28" (312 mm) by 3.43" (87
mm) high
• 2' x 2' - 24.00" (609 mm) by
23.90" (607 mm) by 3.03" (77
mm) high
• 2x4 – 47.5" (1219 mm) x 23.5"
(607 mm) x 3" (77 mm)
ZR-RK Series with
SmartCast Technology
®
LED Retrofit Troffer Kit
INSTALLATION INSTRUCTIONS
4. Designed for use in 120-277V 50-60Hz
(all versions) or 347V 60 HZ (non EB
versions Only) protected circuit (fuse
box, circuit breaker). Supply wire sized
as per NEC or governing code(s).
5. Products with the -EB suffix are
provided with a factory-installed
emergency lighting LED battery pack
and are eligible to serve a s apart of a
facility's emergency lighting system
in accordance with ANSI/NFPA 101
and Article 700 of ANSI/NFPA 70.
6. When mounted at or below 15ft, -EB
products will provide the required
1 foot- candle of luminance on the
floor.
7. Make sure to cap off all unused
leads.
8. Consult your local authority regarding
disposal or recycling of removed
ballast and lamp.
LPN00825X0003A0_A