Related Manuals for Baracoda BDPP01
Summary of Contents for Baracoda BDPP01
- Page 1 Data Capture for Workforce in Motion USB dongle Plug & Scan User Guide ©Baracoda – December 2008...
-
Page 2: Table Of Contents
UNNERS 2 & R OW TO USE WITH ENCIL UNNERS ... 9 EYBOARD EMULATION SPEED HOW TO CONNECT YOUR BARACODA BARCODE SCANNER ... 10 OW TO CONNECT YOUR ARACODA ENCIL BC2604/BL2604/BLR2604... 10 OW TO CONNECT YOUR BCM2604-L/BCM2604-F... 11 OW TO CONNECT YOUR ... -
Page 3: Revision History
Data Capture for Workforce in Motion... -
Page 4: Introduction
Data Capture for Workforce in Motion (*) for Macintosh... -
Page 5: Technical Introduction
Data Capture for Workforce in Motion Note... -
Page 6: No Data Los Mode'
Data Capture for Workforce in Motion by default Your scanner and any future scanners will retain this configuration Enable ‘no data loss mode’ (*) Disable ‘no data loss mode’ Note... -
Page 7: Batch Mode
Data Capture for Workforce in Motion Enable batch mode Upload batch data (for RoadRunners) - Page 8 (for Pencil2 & RoadRunners Evolution) <UPL>: start xxxxx <UPL>: transmission OK <UPL>: transmission NOK Enable batch mode Upload batch data Data Capture for Workforce in Motion...
-
Page 9: Keyboard Emulation Speed
Data Capture for Workforce in Motion Keyboard emulation speed : SLOW Keyboard emulation speed : MEDIUM (*) Intercharacter delay = 20ms Intercharacter delay = 16ms Keyboard emulation speed : HIGH Intercharacter delay = 8ms... -
Page 10: How To Connect Your Baracoda Barcode Scanner
(*) If the LED on the BaracodaPencil is not double flashing green, this may possibly mean: The BaracodaPencil is low on power. Charge the unit up completely and try again The BaracodaPencil has not been reset. Reset it and try again The BaracodaPencil has been programmed from its default status and it is not able to decode the Code 128 symbology. -
Page 11: How To Connect Your Bcm2604-L/Bcm2604-F
(**) If the LED on the BL/BC/BLR2604 is not double flashing a green light, this may possibly mean: The scanner is low on power. Charge the unit up completely and try again The scanner has not been reset. Reset it and try again The scanner has been programmed from its default status and it is not able to decode the Code 128 symbology. - Page 12 Data Capture for Workforce in Motion...
- Page 13 Data Capture for Workforce in Motion...
-
Page 14: How To Disconnect Your Usb Plug & Scan Dongle
Data Capture for Workforce in Motion barcode Disconnect... -
Page 15: Additional Features
Data Capture for Workforce in Motion Disable prefix [default] Horizontal Tab (HT) prefix Disable suffix Horizontal Tab (HT) suffix Carriage Return (CR) suffix... - Page 16 Data Capture for Workforce in Motion Line Feed (LF) suffix Carriage Return (CR) + Line Feed (LF) suffix [default]...
-
Page 17: Only For Bc2604/Bl2604/Blr2604 Products
The Number of Beeps for ‘good scan’ 0 beep [default] 1 beep 2 beeps 3 beeps Data Capture for Workforce in Motion DISCONNECT... - Page 18 The Number of Beeps for ‘ACK’(in ‘no data loss mode’) 0 beep 1 beep [default] 2 beeps 3 beeps Data Capture for Workforce in Motion DISCONNECT...
-
Page 19: Configuration
Data Capture for Workforce in Motion... -
Page 20: Print Firmware Version
Data Capture for Workforce in Motion Print firmware version... -
Page 21: Compatibility
Data Capture for Workforce in Motion... -
Page 22: Limited Warranty
Data Capture for Workforce in Motion...
Need help?
Do you have a question about the BDPP01 and is the answer not in the manual?
Questions and answers