Table of Contents
Advertisement
Quick Links
SPECIFICATIONS
1200URX/AB - 1200URX/Si - 1200URX/VM
RF Carrier Frequency Range
Noise Reduction
Effective Operating Range
Frequency Response
RF Sensitivity (12dB SINAD)
Adjacent Channel Selectivity
Image Rejection
IF Rejection
Audio THD
Audio Output
40dBm ± 40kHz Deviation (-20dBm ± 40kHz Deviation for 1200URX\Si)
Output Impedance
Signal/Noise Ratio
Power Requirements
11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1200URX\Si)
Dimensions
Operating Temperature Range
Weight
1200BT
Output Power
Max Modulation Sensitivity
MIC Level / Imped.
Power Requirements
Dimensions
Weight w/Battery
1200XT
Output Power
Max Modulation Sensitivity
MIC Level / Imped. (Dynamic)
Phantom Power
Power Requirements
3V DC (2 "AA" Alkaline) @ < 180mA - 290 mA w/Phantom Power ON
Dimensions
Weight w/Battery
Due to constant improvements, specifications are subject to change without notice.
Licensing
Licensing of this, or any Azden wireless equipment is the user's responsibility. The ability to receive a license
depends largely on the user's classification, application and frequency. Contact the appropriate agency (FCC in
the USA) for further information.
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
tel - 516.328.7500 • fax - 516.328.7506 • email - sales@azdencorp.com
© 2008 Azden Corporation
188 steps ~ 638.125 - 661.875 MHz
MicroComputer Controlled PLL Synth.
Expander (THAT)
200 - 300 ft ~ 60 - 100m
50 - 15kHz (± 1.5dB)
> 70dB (± 250kHz)
Ω (
Ω (300Ω Ω Ω Ω Ω for 1200URX\Si)
Ω (
600Ω (
Ω (
> 62dB (± 5kHz Deviation) "A" Weighted
68W x 84H x 18D mm- 1200URX/Si insertion
93W x 119H x 49D mm - 1200URX/AB
82W x 150H x 60D mm - 1200URX/VM
-50
0
- +122
0
F ~ -10
8.8 ounces ~ 250g for 1200URX/Si
15.87ounces ~ 450g for 1200URX/AB
26.45ounces ~ 750g for 1200URX/VM
-60dBm / 2.2kΩ Ω Ω Ω Ω (± 5kHz Deviation)
3V DC (2 "AA" Alkaline) @ < 150mA
2.48 (W) x 3.86 (H) x 1.12 (D) inches
63 (W) x 98 (H) x 28.5 (D) mm
6.35 ounces ~ 180g
+20dBM ~ 0dBm
-60dBm / 2.2kΩ Ω Ω Ω Ω (± 5kHz Dev.)
48V ±2V @ 2mA
1.57 (W) x 4.49 (H) x 1.57 (D) inches
40 (W) x 114 (H) x 40 (D) mm
6.35 ounces ~ 180g
Printed in USA
User's Guide
1.2μ μ μ μ μ V
> 93dB
> 93dB
< 0.8%
1200URX/AB • 1200URX/VM • 1200URX/Si
0
- +50
0
C
25mW
-4dBm
25mW
P1030-01
1200BT • 1200XT
ENHANCED BROADCAST PERFORMANCE
UHF WIRELESS SYSTEM
Advertisement
Table of Contents
Related Manuals for Azden 1200BT
Summary of Contents for Azden 1200BT
-
Page 1: Specifications
Due to constant improvements, specifications are subject to change without notice. Licensing Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license depends largely on the user’s classification, application and frequency. Contact the appropriate agency (FCC in the USA) for further information. - Page 2 The bottom segment will blink when the battery power falls to less than 2.2V and indicates that it is time to replace the batteries. Azden recommends the use of Alkaline batteries only. Across the top of the display, up to 5 segments will illuminate depending on the strength of the transmitted audio signal - from 2 (weak) to 5 (strong).
-
Page 3: Introduction
Counterclockwise rotation reduces the input gain while clock- wise rotation increases the input gain. Thank you for selecting the Azden 1200 Series for your portable/ENG on-camera UHF wireless needs. We are confident that these compo- nents will perform beyond your expectations. For over 40 years Azden Corporation has been creating technologically advanced products. -
Page 4: Table Of Contents
The 1200URX/Si ... 4 Mode ... 4 Up/Down ... 5 Powering the 1200BT Transmitter ... 6 SETTING THE TRANSMITTING FREQUENCY ON THE 1200BT ... 6-7 USING THE 1200BT TRANSMITTER’S CONTROLS AND DISPLAY ... 7 Power ... 7 Audio ... 7 MIC ... -
Page 5: Attaching The Antennas
(from 1 to 3 segments) with 3 segments meaning maximum battery power. The bottom segment will blink when the battery power falls to less than 2.2V and indicates that it is time to replace the battery. Azden recommends the use of Alkaline batteries only. -
Page 6: Power
The POWER ON/OFF switch [ ] turns the 1200BT On or OFF. B. Audio Prior to turning the 1200BT ON it is best to set the AUDIO switch [ ] to ST.BY. When ready to transmit, switch to ON. The ST.BY position acts as a ‘mute’... -
Page 7: Powering The 1200Bt Transmitter
1200BT transmitter by first setting the LCD display to one of two views - ‘Frequency’ or ‘Channel’. To do this, after installing fresh batteries, turn the 1200BT to the ON position [ ]. Next, using the tip of a ballpoint pen, an unbent paper clip or something similar, press the MODE but- ton [ ] repeatedly until one of the two screens below appears. -
Page 8: Display
RECEIVER SETUP/USE - 1200URX/AB or 1200URX/VM (continued) As the RF signal from the transmitter gets stronger (or weaker) the number of illuminated LCD segments in the display will change - with 3 segments being the maximum and best. Similarly, the AF (audio level) segments will light from 1 to 3 segments as the audio gets stronger or weaker.