1. Manuals
  2. Brands
  3. Purkeys Manuals
  4. Controller
  5. OneConnect
  6. Diagnostics manual

Purkeys ONECONNECT Diagnostics Manual

Hide thumbs Also See for ONECONNECT:
Table of Contents

Advertisement

Quick Links

Download this manual
A MISSION CRITICAL ELECTRONICS BRAND
ONECONNECT WITH
INTERIOR LIGHT CONTROL
DIAGNOSTIC GUIDE
300-50 R1.01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ONECONNECT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Purkeys ONECONNECT

Summary of Contents for Purkeys ONECONNECT

  • Page 1 A MISSION CRITICAL ELECTRONICS BRAND ONECONNECT WITH INTERIOR LIGHT CONTROL DIAGNOSTIC GUIDE 300-50 R1.01...

  • Page 3: Table Of Contents

    Exterior Switch of Interior Light Operational Check ......9 Troubleshooting: Dual/Single Pole with Interior Lights ......10 Interior Lights Do Not Come On ............10 Exterior Switch of Interior Light Operational Check ......12 Limited Commercial Warranty Policy ............13 P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...

  • Page 4: Troubleshooting: 7-Way With Interior Lights

    TROUBLESHOOTING: 7-WAY WITH INTERIOR LIGHTS INTERIOR LIGHTS DO NOT COME ON Step 1: Inspect the wiring and confirm that all connections are tight. Step 2: Check for a voltage greater than 10 volts to the lights, as shown. • If yes, inspect the wiring between the nosebox and the lights for defects.
  • Page 5 (if installed) for defects. – To check the operation of the external switch, proceed to the next step. • If the lights do not come on, replace the cover assembly. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...

  • Page 6: Exterior Switch Of Interior Light Operational Check

    EXTERIOR SWITCH OF INTERIOR LIGHT OPERATIONAL CHECK Step 6: Position meter to measure the resistance reading. • Press for continuity, if meter has this feature. • Place leads as shown. Press interior light switch - readings should be 0 or very low resistance. •...

  • Page 7: Interior Lights Do Not Come On

    • If all voltages are good: – If exterior switch is used skip to step 6. – If no exterior switch is used proceed to step 5. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
  • Page 8 Step 5: Place the jumper between the posts. • If the lights come on and there is no external switch, replace the cover assembly. • If there is an exterior switch, proceed to the next step. Step 6: Position the meter to read resistance.

  • Page 9: Troubleshooting: Dual Pole With Interior Lights

    Step 3: Check for a voltage greater than 10 volts to the lights, as shown. • If yes, inspect the wiring between the nosebox and the lights for defects. • If no, continue to the next step. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
  • Page 10 Step 4: Check for a voltage greater than 10 volts. • If yes, inspect the wiring in the nosebox for defects. • If no, continue to the next step. Step 5: Check for voltage greater than 10 volts. • If yes, replace the cover assembly.

  • Page 11: Exterior Switch Of Interior Light Operational Check

    • Place leads as shown. • Press the interior light switch. • Voltage should read 0 or a very low resistance. • If no, inspect the wiring between the nosebox and the switch for defects. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...

  • Page 12: Troubleshooting: Dual/Single Pole With Interior Lights

    TROUBLESHOOTING: DUAL/SINGLE POLE WITH INTERIOR LIGHTS INTERIOR LIGHTS DO NOT COME ON Step1: Inspect the wiring and confirm that all connections are tight. Step 2: Turn the interior lights on by pressing the switch on the nosebox, then continue to the following steps. Step 3: Check for a voltage greater than 10 volts to the lights, as shown.
  • Page 13 (if installed) for defects. • To check operation of the external switch, proceed to the next section. • If the lights do not come on, replace the cover assembly. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...

  • Page 14: Exterior Switch Of Interior Light Operational Check

    EXTERIOR SWITCH OF INTERIOR LIGHT OPERATIONAL CHECK Step 1: Position the meter to read resistance. • Press for continuity, if the meter has this feature. • Place leads as shown. • Press the interior light switch. • Voltage should read 0 or a very low resistance.

  • Page 15: Limited Commercial Warranty Policy

    Product or failure of a part not manufactured by Purkeys. This warranty shall not apply if any Purkeys product is used for a purpose for which it is not designed or is in any way altered without the specific prior written consent of Purkeys. ANY...

Table of Contents