Morgan Olson Amazon P80 2019 Service Manual
  1. Manuals
  2. Brands
  3. Morgan Olson Manuals
  4. Offroad Vehicle
  5. Amazon P80 2019
  6. Service manual

Morgan Olson Amazon P80 2019 Service Manual

Package delivery vehicle
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual
2019 Morgan Olson Body
2019 Freightliner MT45 Chassis
1.800.233.4823
WWW.MORGANOLSON.COM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Amazon P80 2019 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Morgan Olson Amazon P80 2019

Summary of Contents for Morgan Olson Amazon P80 2019

  • Page 1 Service Manual 2019 Morgan Olson Body 2019 Freightliner MT45 Chassis 1.800.233.4823 WWW.MORGANOLSON.COM...
  • Page 2 NOTE: USE ONLY GENUINE MORGAN OLSON PARTS USE OF NON OEM PARTS MAY VOID YOUR WARRANTY AND/OR VIOLATE FMVSS SAFETY STANDARDS Latest version of all documents available at; www.morganolsonparts.com Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...

  • Page 3: Table Of Contents

    Contents CONTENTS BODY TIE/DOWNS DOORS Side Doors Adjustments & Lubrication Bulkhead Door Adjustments & Lubrication Rear Door Adjustments & Lubrication 11-21 GAS SPRING HEATER Motor, Fan & Plenum Troubleshooting 24-29 HOOD LAMPS BODY PANEL REPLACEMENT AND RIVETS WINDSHIELD Windshield Removal and Installation WINDSHIELD WIPERS &...

  • Page 4: Body Tie/Downs

    Body Tie/Downs Tie/Down Check: The floor of the truck is fastened to bolsters that extend the length of the floor. The lower flanges of the bolsters are mounted to the chassis frame rails. Both sets of fasteners are torqued to specifications. All cab and body tie/downs should be checked after 3 months and annually.

  • Page 5: Side Doors Adjustments & Lubrication

    Side Door Side Door For smooth operation the locking mechanism should be oiled every 3 months or as needed. Grease should also be added at the contact points of locking mechanism arm and striker. (At opened and closed positions.) Lubricate latch internal mechanism. Grease on the latch contact points.
  • Page 6 Side Door Removal: 1. Remove the anti rattle clips. 2. Remove the 4 fasteners and the door handles (inner and outer). 3. Using a socket wrench, remove the bolts fastening the door and hanger assembly. 4. To simplify door removal, remove the grab handle located forward of the door. *Fold side view mirror back.
  • Page 7 Side Door Installation: 1. Tilt the top of the door in place first. Now position the bottom of the door into the lower door track, which is in position but not fastened down. 2. Put 1/8” shims between the lower door track and the wear strip. 3.
  • Page 8 Side Door Adjustment: 1. Loosen all nuts on the top of the slotted upper door track. 2. With the door closed and engaged in the forward strike, adjust the upper track for uni- form lateral placement of the door in the forward post seal. Snug the forward bolt of the upper door track.
  • Page 9 2019 Amazon P80 Package Delivery Vehicle...

  • Page 10: Bulkhead Door Adjustments & Lubrication

    Blank Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...

  • Page 11: Rear Door Adjustments & Lubrication

    Bulkhead Door Bulkhead Door: *NOTE: Where grease is required use a lithium based. 1. The latch should be greased to prevent sticking. Grease should be applied at contact points of the latch and striker for smooth operation. This should be done every 3 months. 2.
  • Page 12 225 NORTH PATTERSON ST. CAREY, OH 43316 CUSTOMER SERVICE PHONE 877-876-7452 ROLL-UP DOOR PREVENTIVE MAINTENANCE CHECKLIST The Counterbalance Spring is wound under High Tension. This High Tension Counterbalance Spring can cause Severe Injury or Death. Only Qualified technicians should adjust this spring. Use two winding bars that are ½”...
  • Page 13 LUBRICATION Lubricate the Counterbalance Spring, Counterbalance Shaft Bearings, Rollers, Hinges, Top Fixtures, Bottom Roller Holders and Locks liberally with Transglobal Lube. Do NOT use grease. Wipe dirt from track. Frequency of door maintenance will vary with climate conditions and door cleaning procedures. Doors which are steam cleaned will need lubricated more often.
  • Page 14 LUBRICATION OF END HINGES, 2-POINT CENTER CONTROL & END LATCHES END HINGE 2-POINT CENTER CONTROL ASSEMBLY 2-POINT END LATCH ASSEMBLY Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com Copyright © 2017 by Transglobal Inc.
  • Page 15 LUBRICATION OF TOP FIXTURE, CENTER HINGE & BOTTOM FIXTURE TOP FIXTURE CENTER HINGE BOTTOM FIXTURE 2019 Amazon P80 Package Delivery Vehicle...
  • Page 16 LUBRICATION OF SINGLE AND DUAL SPRING ASSEMBLIES On single and dual spring assemblies – lubricate spring(s) along their entire length to prevent rusting. SINGLE SPRING ASSEMBLY DUAL SPRING ASSEMBLY Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 17 DOOR OPERATION – PLEASE INSPECT THE FOLLWING: Check to see if the door lock operates easily and latches tight, compressing the bottom seal. Check to see if the door operates freely (up and down) with side play between the tracks and door approximately ¼”...
  • Page 18 Loosen the two 5/16” nuts on both top fixture assemblies, adjust the top fixture slides until the top door panel is in the same plane as the rest of the door panels and retighten 5/16” nuts. REAR STRUCTURE TOP HEADER TOP FIXTURE ASSEMBILY TOP PANEL SEAL FIGURE 2...
  • Page 19 PULL STRAP PULL STRAP RETAINER PULL STRAP (INSIDE MOUNT SHOWN) FIGURE 3 Failure to replace worn or frayed door pull strap may result in injury. 2019 Amazon P80 Package Delivery Vehicle...
  • Page 20 SPRING BALANCER – PLEASE INSPECT THE FOLLOWING: Note: All spring systems are designed to assist in the operation of opening and closing the door. The door should never free fall or fly open buy itself. All spring systems are designed for both cables to SPRING BALANCER –...
  • Page 21 LOCATIONS OF TRANSGLOBAL’S SERIAL NUMBER PLATES Transglobal has (2) location. Outside mount / bottom panel / RS (Standard) and inside mount / top panel / RS. When ordering parts for roll-up door, specify the serial number of the door. 2019 Amazon P80 Package Delivery Vehicle Copyright ©...

  • Page 22: Gas Spring

    1. With the hood safely propped, remove the upper and lower retainer clips. Once the clips have been removed a slight tap will remove the gas spring from the ball studs. 2. For safety reasons, when replacing the gas springs use only Morgan Olson OEM replace- ment parts.

  • Page 23: Heater

    Heater Motor and Fan Replacement: 1. The heater is mounted to the right hand dash panel. 2. With the power to the motor off, disconnect the motor leads. 3. Remove motor mounting screws. Remove the motor and the impeller wheel. 4.

  • Page 24: Troubleshooting

    SERVICING AND TROUBLESHOOTING HEATER/DEFROSTER CONTROL PANEL OPERATION BLOWER CONTROL The Blower Control provides three blower speeds and OFF. Rotat- ing the blower knob clockwise increases the blower speed. Returning the blower knob to Off will turn-off the blower motor, but will not, necessarily, turn off all air flow;...
  • Page 25 2019 Amazon P80 Package Delivery Vehicle...
  • Page 26 TROUBLESHOOTING SECTION A: AIRFLOW PROBLEMS PROBLEM A-1 , No air flow, blower does not operate POSSIBLE CAUSE #1 ~ Faulty Blower Motor CORRECTIVE ACTION ~ With the ignition turned ON, unplug the 2-pin connector at the blower motor. Check the orange wire for +12 volts and the white wire for a fully grounded circuit. If power is present and the circuit is grounded, remove the motor and blower wheel from the blower housing.
  • Page 27 PROBLEM A-3 ~ Air does not flow from the selected outlets POSSIBLE CAUSE #1 ~ Plenum directional door obstructed. CORRECTIVE ACTION ~ Examine the air distribution Plenum for any possible obstruction that might have become entrapped internally. Refer to the Mode Selection – Electrical and Mechanical Correla- tion diagram for the position of the door relative to the position of the Temperature Control knob.
  • Page 28 POSSIBLE CAUSE #2 ~ Servo motor failure CORRECTIVE ACTION ~ If servo motor failure is suspected, the first step is to confirm that the electri- cal connection at the servo motor is delivering the correct signal to the servo motor. With the ignition switch turned to Accessory, unplug the servo connector and test according to the information in the Mode Selection-Electrical and Mechanical Correlation diagram.
  • Page 29 Blank 2019 Amazon P80 Package Delivery Vehicle...

  • Page 30: Hood

    HOOD Hood Removal: 1. For removal of the gas springs. See page 28. 2. Disconnect wire harness plug connections. 3. Remove the 4 bolts tying the left and right hinge assemblies to the body of the truck. 4. Disconnect hood prop. 5.

  • Page 31: Lamps

    LAMPS Headlight Replacement: 1. Remove screws and trim ring from around headlight. 2. Remove headlight. 3. Remove wiring plug from back of headlight. 4. Replace headlight. 5. For installation reverse removal sequence. Tail, Turn Backup and Marker Lamp Replacement: 1. Push tail, turn back-up lamp into rubber grommet and use a small flat head screw driver and pry lamp from rubber grommet.

  • Page 32: Body Panel Replacement And Rivets

    BODY PANEL REPLACEMENTS & RIVETS Body Panel Replacement: 1. When replacing exterior body panels, remove rivets following procedures outlined below. 2. Apply sealant to new panel as required. 3. Install new panel in reverse order. Removing A Rivet: 1. When removing an existing rivet, place the drill bit on the small dot in the center of the rivet head.

  • Page 33: Windshield Removal And Installation

    WINDSHIELD REPLACEMENT Windshield Removal: 1. Special tools are required for windshield removal. Glass and Bead Tools. 2. A soap and water solution should be applied around the rubber seal. This will allow the tools to move smoothly when in contact with the rubber seal. 3.

  • Page 34: Windshield Wipers & Motor

    WINDSHIELD WIPERS & MOTOR Windshield Wipers and Wiper Drive Assembly: 1. Replace the wiper arm by removing the acorn nut and washer hose. To insure proper placement of the new wiper, mark the position of the old wiper arm before removing. 2.
  • Page 35 WINDSHIELD WIPER ASSEMBLY Windshield Wipers and Wiper Drive Assembly: Fron inside of cab, remove upper wiper cover and disconnect power to the wiper motor. Disconnect the washer hose from the pivot cover. From the outside, remove the acorn retaining nuts, disconnect the washer hoses, remove the wiper arms.

  • Page 36: 360 Camera Systems

    360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 37 360 CAMERA SYSTEM 2019 Amazon P80 Package Delivery Vehicle...
  • Page 38 360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 39 360 CAMERA SYSTEM 2019 Amazon P80 Package Delivery Vehicle...
  • Page 40 360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 41 Wiring Diagram 2019 Amazon P80 Package Delivery Vehicle...
  • Page 42 360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 43 360 CAMERA SYSTEM 2019 Amazon P80 Package Delivery Vehicle...
  • Page 44 360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 45 360 CAMERA SYSTEM 2019 Amazon P80 Package Delivery Vehicle...
  • Page 46 360 CAMERA SYSTEM Genuine OEM Parts 1.800.233.4823 www.morganolsonparts.com...
  • Page 47 360 CAMERA SYSTEM 2019 Amazon P80 Package Delivery Vehicle...
  • Page 48 Troubleshooting Symptom Possible Condition Solution Check Connections at power No Power Poor Connection \ Fuse wires and ground wires. Check Vehicle fuse Check in-line fuse in the wire harness to monitor Check inline fuse in the wire harness to the signal processor In line fuses are located in the wiper compartment above the driver seat.

  • Page 49: Key-Less Entry System

    KEYLESS ENTRY Bulkhead Door 1. Press and hold fob button for 1-second 2. Bulkhead door automatically opens and remains open until driver manually closes door 3. Door automatically latches and locks when door closes Bulkhead Door Quick Open 1. After stopping the truck using the Engine Stop button 2.
  • Page 50 CODE ENROLLMENT Quick Code Enrollment 1. Car MUST be stopped AND engine OFF 2. Press the fob button once Engine Start / Stop switch back light begins flashing, indicating a Valid ID has been detected 3. Press and HOLD the Engine Stop switch for 5-seconds Engine Start / Stop switch back light will turn ON solid 4.
  • Page 51 Blank 2019 Amazon P80 Package Delivery Vehicle...

  • Page 52: Electrical Wiring Diagrams

    WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 53 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 54 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 55 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 56 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 57 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 58 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 59 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 60 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 61 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 62 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 63 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 64 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 65 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 66 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 67 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 68 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 69 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 70 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 71 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 72 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 73 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 74 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 75 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 76 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 77 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 78 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 79 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 80 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...
  • Page 81 WIRING DIAGRAMS Morgan Olson Service Parts 1.800.233.4823...

Table of Contents