Advertisement
Installations
(continued)
3. Install the inner cover.
Slide the covers located on the both lateral sides
of the camera and put the inner cover on the
camera until the hooks inside the inner cover are
held in the holes of the camera (until a click is
heard).
Important: Put the inner cover down on the cam-
era until the outside cover of the camera can-
not be seen from the opening (from which the
camera lens is visible) of the inner cover. If this
integration is not successfully performed, the
inner cover may be removed or the hidden part
at the top of the screen may become larger in
the WIDE mode.
How to remove the inner cover
Press the inner cover from the front and rear
sides inward (at the same vertical position as the
hooks) to bend the cover and remove the shell
from the camera.
4. Mount the top cover on the wall and run the cables.
Fix the top cover with four screws. Screws are not
provided.
Prepare them in accordance with the camera
installation position.
• Necessary screw: M4 (4 pcs.)
• Minimum pull-out strength: 196 N {44 lbf}
5. Mount the camera.
Refer to the Instal lation Guide of network camera
for further information.
The camera mount bracket is already attached to
the top cover at the time of purchase.
Make sure to use the pre-installed camera mount
bracket.
Important: When mounting the camera, push the
camera securely into the mounting section of
the top cover.
6. Mount the bottom cover.
Be sure to push the bottom cover up until a click
is heard.
Important: Do not let the cables be caught during
installation work.
Inner cover
Cover
Hook
Put on until a click is heard
Press from the front and rear
sides inward to bend
Screws
(M4, to be separately purchased)
Safety wire
Camera fixing screw
(accessory of the network camera)
Bottom cover
7. Tighten the fixing screw to be used for cover fall prevention.
Recommended tightening torque: 1.6 N·m {1.18 lbf·ft}
8. Remove the protection sheet from the dome cover.
Remove the cover film from the dome cover after the installation is completed.
Note: When the camera is pointed in the horizontal direction, the upper side of the screen is hidden.
Refer to the Operating Instructions of network camera for further information.
Specifications
Ambient temperature:
–10 °C to +50 °C {14 °F to 122 °F}
Dimensions:
165 mm (W) x 206.5 mm (H) x 217.5 mm (D)
{6-1/2 inches (W) x 8-1/8 inches (H) x 8-9/16 inches (D)}
Approx. 950 g {2.10 lbs.}
Mass:
Finish:
Main body
Top and bottom covers : ABS resin with silver metallic coating
Dome cover
Standard Accessories
Operating Instructions (this document) ........................ 1 pc.
The following are for installation.
Template ..................................................................... 1 sheet
Inner cover ................................................................. 1 pc.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
© Panasonic Corporation 2017
: Treatment steel
: PMMA resin
Clear
WV-Q158C
Smoke WV-Q158S
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Advertisement
