Advertisement
Quick Links
®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2002 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Straight, Corner, Corner Dual, or Straight Dual Unit
Straight or Corner Bilevel Unit
Extended or Hyperextended on Standard Corner Units
Left
Right
Extension
Extension
Extended or Hyperextended on Bilevel Corner Units
Left
Right
Extension
Extension
Please identify the unit before selecting what section to follow
(begins on page 13)
Hyper
Extended
(begins on page 26)
Hyper
Extended
Crank Adjustable Units
for assembly of product.
Section A
(begins on page 2)
Section B
(begins on page 8)
Section C
Section D
939504740 Rev E
Page 1 of 37
Advertisement
Related Manuals for Stellcase Lift and Lock Jules Platform with Standard Palm Rest
Summary of Contents for Stellcase Lift and Lock Jules Platform with Standard Palm Rest
- Page 1 Crank Adjustable Units Please identify the unit before selecting what section to follow for assembly of product. ® Straight, Corner, Corner Dual, or Straight Dual Unit Section A (begins on page 2) Straight or Corner Bilevel Unit Section B (begins on page 8) Extended or Hyperextended on Standard Corner Units Section C (begins on page 13)
- Page 2 Section A Assembly instructions to assemble the following units: Crank Short Worksurface Foot Handle Mounting Screw Bolt (Qty. 1) Screw (Qty. 6) (Qty. 4) (Qty. 8) Page 2 of 37 939504740 Rev E...
- Page 3 without Flip the base upside down and cutting the tie wraps, put the feet on. Foot Bolts Front Page 3 of 37 939504740 Rev E...
- Page 4 Straight Standard Install grommet (black) into laminated side of worksurface. Install guide (white) into grommet. Corner Standard Corner Dual Straight Dual Page 4 of 37 939504740 Rev E...
- Page 5 (optional) Washer Cut the tie wraps. (Optional for STANDARD and DUAL units only) Install the "nut", "washer" and "disk" to the gas cylinder (if not already installed). Place gas Gas Cylinder cylinder as shown. NOTE: DO NOT attempt to screw or compress the gas cylinder into place.
- Page 6 Standard Straight Place the worksurface on a protected surface. Attach mounting plates on worksurface, at the screw locations shown, after aligning the pilot holes. Standard Corner Rear Front Rear Straight Dual Rear Worksurface Screws Front Front Page 6 of 37 939504740 Rev E...
- Page 7 NOTE: If unit is placed with a gas cylinder, adjust the unit to full height of travel using crank handle. Flip base upside down on a protected surface. NOTE: If base has gas cylinder, be careful when inverting the base. Mount top to base with short mounting screws.
- Page 8 Section B Assembly instructions to assemble the following units: Crank Short Worksurface Foot Handle Mounting Screw Bolt (Qty. 1) Screw (Qty. 16) (Qty. 4) (Qty. 8) Page 8 of 37 939504740 Rev E...
- Page 9 without Flip the base upside down and Foot Bolts cutting the tie wraps, put the feet on. Front Page 9 of 37 939504740 Rev E...
- Page 10 Install grommet (black) into laminated side of worksurface. Install guide (white) into grommet. Straight Bilevel Corner Bilevel Page 10 of 37 939504740 Rev E...
- Page 11 Bilevel Straight Rear Place worksurface on a protected surface. Attach mounting plates on worksurface. Front Bilevel Corner Rear Front Worksurface Screws Page 11 of 37 939504740 Rev E...
- Page 12 Cut tie wraps. Flip base upside down on a protected surface. Short Mounting Screws Mount top to base with short mounting screws. Straight Bilevel Corner Bilevel Flip unit to upright. Remove Guides, retain for future assembly. Test: Using the crank handle, adjust both the front and the rear surfaces of the unit to different heights to ensure unit works properly.
- Page 13 Section C Assembly instructions to assemble the following units: Strap Short Long Crank Screw Mounting Handle Mounting (Qty. 8 max) Screw Screw (Qty. 1) (Qty. 12 max) (Qty. 4) Foot Connector Worksurface Spacer Bolt Plate Screw (Qty. 1) (Qty. 8 max) Screw (Qty.
- Page 14 without Flip the base upside down and Foot Bolts cutting the tie wraps, put the feet on. Front NOTE: The large crossbar MUST be in front for Standard Unit. Page 14 of 37 939504740 Rev E...
- Page 15 Install grommet (black) into laminated side of worksurface. Install guide (white) into grommet. Corner Standard Page 15 of 37 939504740 Rev E...
- Page 16 (optional) Washer Cut the tie wraps. (Optional for STANDARD and DUAL units only) Install the "nut", "washer" and "disk" to the gas cylinder (if not already installed). Place gas Gas Cylinder cylinder as shown. NOTE: DO NOT attempt to screw or compress the gas cylinder into place.
- Page 17 Connector Screw Flip worksurface over on a protected surface. Attach connector plates to corner worksurface. Connector Plate Make sure the recessed holes are facing away from the worksurface at the holes that align with the worksurface pilot holes. Page 17 of 37 939504740 Rev E...
- Page 18 Loop chain over sprocket making sure that the extensions must have the crossbars to the front. NOTE: Do not pull the chain in any direction as this could affect the height of the base. Cut tie wraps. NOTE: The front of the feet must be pointed towards the inside of workstation.
- Page 19 Adjust the extension links so as to align the slots. Page 19 of 37 939504740 Rev E...
- Page 20 Washer Install gas cylinder into open column of extension bases. NOTE: DO NOT attempt to screw in or compress the gas cylinders into place. Cylinder OPTIONAL: If standard hyperextension unit has an extra pair of gas cylinders (ordered separately), place them now. CAUTION: Cylinder under compression! To avoid possible injury when servicing cylinder, raise worksurface to uppermost position and remove...
- Page 21 Standard Unit Hyperextended Place the long mounting screw into the slots to prevent detachment of the extensions. Crank the unit using the crank handle to top of travel. Make sure that the gas cylinder sits BELOW the top surface. long Attach standard mounting plates at base/ short extension junction (one location for extended, two...
- Page 22 Standard Unit Extended Only (For single side Extended units only) Place spacer as shown in one location only - on non extended side to ensure a level surface. NOTE: Only one spacer needed per assembly of single side extended unit. Never place a spacer on the extension base.
- Page 23 Standard Unit Hyperextended Only Attach the mounting plates on the extensions using short mounting screws. Leave screws loose. Check if the unit is leveled at this point by measuring the distance from the foot to the mounting plate. If not leveled then undo steps 7 - 15 of this section.
- Page 24 FOR STANDARD UNITS Place and install corner worksurface. Mount top to base with worksurface screws at the specified holes by aligning the mounting plate holes to the worksurface pilot. REAR FRONT WORKSURFACE SCREW Page 24 of 37 939504740 Rev E...
- Page 25 TIP: Level the extension with the base by measuring the height from floor (or top of foot casting). If not levelled, remove worksurface by undoing all the worksurface screws; undo steps to remove mounting plates, pull chain to adjust height. Repeat measurement above, do steps to attach mounting plate and worksurface.
- Page 26 Section D Assembly instructions to assemble the following units: Long Strap Short Mounting Crank Screw Mounting Handle Screw (Qty. 8 max) Screw (Qty. 1) (Qty. 4) (Qty. 12 max) Connector Foot Plate Bolt Worksurface Spacer Screw (Qty. 8 max) Screw (Qty.
- Page 27 without Flip the base upside down and cutting the tie wraps, put the feet on. Foot Bolts Front Page 27 of 37 939504740 Rev E...
- Page 28 Install grommet (black) into laminated side of worksurface. Install guide (white) into grommet. Corner Bilevel Page 28 of 37 939504740 Rev E...
- Page 29 Connector Screw Flip worksurface over on a protected surface. Attach connector plates to corner worksurface. Connector Plate Make sure the recessed holes are facing away from the worksurface at the holes that align with the worksurface pilot holes. Page 29 of 37 939504740 Rev E...
- Page 30 Loop chain over sprocket making sure that the extensions must have the crossbars to the front. NOTE: Do not pull the chain in any direction as this could affect the height of the base. Cut tie wraps. NOTE: The front of the feet must be pointed towards the inside of workstation.
- Page 31 Adjust the extension links so as to align the slots. Page 31 of 37 939504740 Rev E...
- Page 32 Washer Install gas cylinder into open column of extension bases. NOTE: DO NOT attempt to screw in or compress the gas cylinders into place. Cylinder CAUTION: Cylinder under compression! To avoid possible injury when servicing cylinder, raise worksurface to uppermost position and remove worksurface prior to removing mounting plate.
- Page 33 Bilevel Unit Hyperextended short Attach bilevel mounting plates at base/extension junction (one location for extended, two locations for hyperextended), but leave screws loose. Use long mounting screws in the front and short mounting screws in the back. Leave screws loose. long Crank the unit using the crank handle to top of travel.
- Page 34 Bilevel Unit Extended Only (For single side Extended units only) Place spacer as shown in one location only - on non extended side to ensure a level surface. NOTE: Only one spacer needed per assembly of single side extended unit. Never place a spacer on the extension base.
- Page 35 short mounting screws at back Attach the standard mounting plates on the extensions using short mounting screws. Leave screws loose. Check if the unit is leveled at this point by measuring the distance from the foot to the mounting plate. If not leveled then undo steps 7-15 of this section.
- Page 36 Place and install corner worksurface. FOR BILEVEL UNITS Mount top to base with worksurface screws. Worksurface Screws Page 36 of 37 939504740 Rev E...
- Page 37 TIP: Level the extension with the base by measuring the height from floor (or top of foot casting). If not levelled, remove worksurface by undoing all the worksurface screws; undo steps to remove mounting plates, pull chain to adjust height. Repeat measurement above, do steps to attach mounting plate and worksurface.
Need help?
Do you have a question about the Lift and Lock Jules Platform with Standard Palm Rest and is the answer not in the manual?
Questions and answers