Table of Contents
Advertisement
Available languages
Available languages
English
introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
Your new Philips Professional Power hair clipper enables
comfortable clipping of even the toughest hair. To enjoy
using the hair clipper, we advise you to read the following
information.
general description (Fig. 1)
A Cutting element
B
Clipping attachment
C Charging light
D On/off slide
E
Handle
F
Socket for appliance plug
g Large comb
h Small comb
i
Setting indications
J
Stubble comb
K
Setting selector
l
Appliance plug
M Adapter
n Cleaning brush
important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
-
Make sure the adapter does not get wet.
Warning
-
Check if the voltage indicated on the adapter and on
the appliance corresponds to the local mains voltage
before you connect the appliance.
-
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
-
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
-
Children should be supervised to ensure that they
do not play with the appliance.
-
Remove the clipping attachment from the handle
before you clean the clipping attachment under the
tap.
Caution
-
Never immerse the handle in water or any other
liquid, nor rinse it under the tap.
-
Do not use the appliance in the bath or in the
shower.
-
The clipping attachment of the appliance complies
with the internationally approved IEC safety
regulations and can be safely cleaned under a
tap (Fig. 2).
-
Use, charge and store the appliance at a temperature
between 15°C and 35°C.
-
Only use the adapter supplied to charge the
appliance.
-
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
-
Do not use the appliance when the clipping
attachment or one of the combs is damaged or
broken as this may cause injury.
-
This appliance is only intended for clipping human
scalp hair. Do not use it for any other purpose.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientific
evidence available today.
Preparing for use
Charging
Charge the appliance for at least 10 hours before you use
it for the first time and after a long period of disuse.
When the appliance is fully charged, it has a cordless
operating time of up to 35 minutes.
4222.002.80001
Do not charge the appliance for more than 24 hours.
1
Make sure the appliance is switched off.
2
Insert the small plug into the socket of the
appliance and put the adapter in the wall
socket (Fig. 3).
3
After a few seconds, the charging light goes on to
indicate that the appliance is charging (Fig. 4).
Note: The charging light does not change colour and does
not go out when the appliance is fully charged.
Optimising the lifetime of the rechargeable
batteries
To optimise the lifetime of the batteries, follow the
instructions below:
-
After the appliance has been charged for the first
time, do not recharge it between clipping sessions.
Continue using it and recharge it only when the
batteries are almost empty.
-
Remove the adapter from the wall socket when the
batteries are fully charged (which takes 10 hours).
-
Discharge the batteries completely twice a year
by letting the motor run until it stops. Then fully
recharge the batteries.
Corded clipping
Note: Only run the appliance from the mains when the
rechargeable batteries are empty.
Note: If the batteries are completely empty, wait a few
minutes before you switch on the appliance.
1
Switch off the appliance.
2
Insert the small plug into the appliance and put the
adapter in the wall socket (Fig. 3).
3
After a few seconds, switch on the appliance.
Using the appliance
Preparing for hair clipping
Only use the appliance on clean, dry hair. Do not use it
on freshly washed hair.
1
Make sure that the head of the person whose hair
you intend to cut is at the same level as your chest.
This ensures that all parts of the head are clearly
visible and within easy reach.
2
Comb the hair in the growth direction (Fig. 5).
Clipping with comb
The appliance comes with three combs for 15 different
hair lengths.
The minimum remaining hair length is 1.6mm and the
maximum remaining hair length is 41mm.
1
Select the comb you want to use.
The table shows how long the hair will be after clipping at
the different settings of the small comb and large comb.
settings of the small and large comb
Setting
Hair length after
clipping with
small comb
1
3mm
2
6mm
3
9mm
4
12mm
5
15mm
6
18mm
7
21mm
Tip: Write down the settings you have used to create a
certain hairstyle as a reminder for future clipping sessions.
stubble comb for a 'stubble look'
-
To create a 'stubble look', clip with the small comb
set to setting 1 (3mm) first.
-
Then clip the hair with the stubble comb for a hair
length of 1.6mm.
2
Slide the selected comb into the guiding grooves on
both sides of the handle ('click') (Fig. 6).
3
To set the comb to the desired setting, press the
setting selector (1) and slide the comb to the
desired hair length setting (2) (Fig. 7).
The setting indications on the comb show the
,
selected setting.
4
Switch on the appliance.
5
Move the appliance through the hair slowly.
-
To clip in the most effective way, move the appliance
against the direction of hair growth.
-
Since all hair does not grow in the same direction,
you need to move the appliance in different
directions (upward, downward or across) (Fig. 8).
-
Make sure that the flat part of the comb is always
fully in contact with the scalp to obtain an even
result.
-
Make overlapping passes over the head to ensure
that you cut all the hair that needs to be cut.
-
To achieve a good result with curly, sparse or long
hair, use a hand comb to guide the hair towards the
appliance.
6
Regularly remove cut hair from the comb.
If a lot of hair has accumulated in the comb, remove
the comb from the appliance and blow and/or shake the
hair out of it.
Contouring without comb
You can use the appliance without comb to clip hair very
close to the skin (0.6mm) or to contour the neckline and
the area around the ears.
Be careful when you clip without comb because the
cutting element removes every hair it touches.
1
Pull the comb off the appliance (Fig. 9).
2
Before you start to contour the hairline around the
ears, comb the hair ends over the ears.
3
Tilt the appliance in such a way that only one edge
of the cutting element touches the hair ends when
you shape the contours around the ears (Fig. 10).
Only cut the hair ends. The hairline should be close to
the ear.
4
To contour the neckline and sideburns, turn the
appliance and make downward strokes (Fig. 11).
Move the appliance slowly and smoothly. Follow the
natural hairline.
Cleaning
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol or
acetone or ethereal oils to clean the appliance.
Note: The appliance does not need any lubrication.
Clean the appliance every time you have used it.
1
Make sure the appliance is switched off and
disconnected from the mains.
Hair length after
2
Remove the comb from the appliance.
clipping with
3
To remove the clipping attachment, turn it
large comb
anticlockwise until the open dot on the handle is
23mm
aligned with the arrow on the attachment (1). Then
lift the attachment off the handle (2) (Fig. 12).
26mm
4
Push the centre top end of the cutting element
upwards with your thumb until it opens and then
29mm
pull it off the appliance (Fig. 13).
Be careful that the cutting element does not fall on the
32mm
floor.
35mm
5
Clean the cutting element with warm water (max.
40°C).
38mm
6
Clean the clipping attachment under warm
running water to flush out the cut hair that has
41mm
accumulated in the attachment (Fig. 14).
7
After cleaning, place the lug of the cutting element
in the slot of the clipping attachment and push
the cutting element back onto the clipping
attachment (Fig. 15).
8
Clean the handle and the adapter with the cleaning
brush supplied or a dry cloth.
Note: The handle and the adapter are not water-proof.
2/9
Advertisement
Table of Contents
