Table of Contents
Advertisement
Quick Links
LORENZ MESSTECHNIK GmbH
Operation Manual
for Torque Sensors
For below and similar Types
DR-1986
DR-1988
E-Mail: info@lorenz-sensors.com
Internet:
www.lorenz-sensors.com
Technical changes reserved
Obere Schloßstr.131
07172 / 93730-0
73553 Alfdorf
Fax 07172 /93730-22
DR-1987
DR-2124
090327.docx
Page 1 of 12
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lorenz DR-1986
Summary of Contents for Lorenz DR-1986
- Page 1 LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Operation Manual for Torque Sensors For below and similar Types DR-1986 DR-1987 DR-1988 DR-2124 E-Mail: info@lorenz-sensors.com Technical changes reserved 090327.docx Internet: www.lorenz-sensors.com Page 1 of 12...
- Page 2 LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Imprint Manufacturer, Place Lorenz Messtechnik GmbH, D-73553 Alfdorf. Valid for... DR-1986; DR-1987; DR-1988; DR-2124 Copyright © 2012 Lorenz Messtechnik GmbH, Alfdorf. Reprint Interdiction Reprints, even in extracts, only with written authority.
-
Page 3: Table Of Contents
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Contents Read First .............................. 4 Safety and Caution Symbols ......................4 Intended Use ..........................4 Dangers ............................4 1.3.1 Neglecting of Safety Notes ..................... 4 1.3.2 Remaining Dangers ........................ -
Page 4: Read First
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Read First Safety and Caution Symbols Caution: Injury Risk for Persons Damage of the Device is possible. Note: Important points to be considered. Intended Use Torque sensors are intended for the measurement of torques. This measurand is further suitable for control tasks. -
Page 5: Term Definitions
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Term Definitions Terms Measuring Side: Mechanical connection of the torque sensor in which the torque to be measured is applied. Usually this side has the smallest moment of inertia. -
Page 6: Electrical Setup
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Electrical Setup The supply of the rotor electronics occurs by an alternating voltage, generated in the stator, which transfers to the rotor through a rotating transformer. There, it is rectified and stabilized. With this supply, the strain gauge bridge is fed. -
Page 7: Mechanical Assembly
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Mechanical Assembly Installation Instructions: It must be ensured that no materials (e.g. liquids, gases) from other components of the spindle get into the torque sensor. Before the assembly, spline drive (or square drive) must be cleaned with dissolver (e.g. -
Page 8: Electrical Connection
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Electrical Connection Pin Connection The torque sensors are equipped with a 12-pin connector (Binder miniature circular connectors series 680, 12-pin) 5.1.1 Standard Version Also see data sheet... -
Page 9: Shielding Connection
Torque means clockwise or clockwise torque if the torque acts clockwise when facing the shaft end. In this case a positive electrical signal is obtained at the output. Torque sensors by Lorenz Messtechnik GmbH can measure both, clockwise and counter-clockwise direction. -
Page 10: Natural Resonances
Date Date Date Control of cables and connectors 1x p.a. Calibration < 26 months Control of fixation (flanges, shafts) 1x p.a. Have bearings exchanged by Lorenz 20000 hrs Messtechnik GmbH operating time E-Mail: info@lorenz-sensors.com Technical changes reserved 090327.docx Internet: www.lorenz-sensors.com... -
Page 11: Trouble Shooting
LORENZ MESSTECHNIK GmbH Obere Schloßstr.131 07172 / 93730-0 73553 Alfdorf Fax 07172 /93730-22 Trouble Shooting This chart should help to search for the most frequent errors and their elimination Problem Possible Cause Trouble Shooting No signal No sensor excitation ... -
Page 12: Disposal
The calibration of the sensor is carried out according to the guidelines of the DKD. The surveillance of the calibrating-laboratory takes place by the DKD. At this calibration, the uncertainty of measurement of the torque measuring instrument is determined. Further information can be obtained from Lorenz Messtechnik GmbH.
Need help?
Do you have a question about the DR-1986 and is the answer not in the manual?
Questions and answers