Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AVANT 313S 2018
Summary of Contents for AVANT 313S 2018
- Page 1 English 313S / 320S Operator’s Manual 2018-...
-
Page 2: Table Of Contents
Table of contents 300S Series TABLE OF CONTENTS INTRODUCTION .......................3 AVANT 300S SERIES WARRANTY ...................3 EC DECLARATION OF CONFORMITY ................4 HOW TO WORK SAFELY ....................5 DECAL LOCATIONS ......................6 MAIN PARTS OF THE LOADER ..................7 TECHNICAL SPECIFICATION ..................8 TECHNICAL SPECIFICATION, ENGINES ................9 LOAD DIAGRAM ......................10... -
Page 3: Introduction
Introduction, warranty INTRODUCTION AVANT TECNO OY wants to thank you for purchasing an AVANT loader. It is the result of Avant’s long experience in design and manufacturing of compact loaders. We ask you that you read and understand the contects of this manual completely before operating the loader. -
Page 4: Ec Declaration Of Conformity
EC declaration of conformity 300S Series EC DECLARATION OF CONFORMITY 1. Manufacturer: Avant Tecno Oy 2. Address: Ylötie 1 FI-33470 YLÖJÄRVI FINLAND 3. Technical Construction File Location: Same as Manufacturer 4. We hereby declare that the machines listed below conform to EC Directives: 2006/42/EC (Machinery), 2014/30/EC (EMC) and 2000/14/EC (Noise Emission). -
Page 5: How To Work Safely
Keep hands, feet and clothing away from any moving Never modify the loader or add attachments not part and/or hydraulic cylinder. approved by AVANT Tecno Oy. Never carry passengers. Keep other bystanders away Do not smoke during refueling or driving. -
Page 6: Decal Locations
Decal locations 300S Series DECAL LOCATIONS The following decals and signs should always be installed on the loader. If any of these decals has been removed or is unreadable it should be replaced without delay. -
Page 7: Main Parts Of The Loader
300S Series Main parts of the loader MAIN PARTS OF THE LOADER Following picture shows the main parts of the loader: Frame Attachment coupling plate The machine has a rigid frame, on which Attachments are mounted on the all the hydraulic components, engine, attachment coupling plate. -
Page 8: Technical Specification
Technical specification 300S Series TECHNICAL SPECIFICATION AVANT Model AVANT 313S AVANT 320S 320S+ Length 1680 mm 1950 mm 1950 mm Width 790-1050 mm 790-1050 mm 790-1050 mm (depending on (depending on (depending on tyre size) tyre size) tyre size) Standard tyre size 5x10 TR 23*8.50-12... -
Page 9: Technical Specification, Engines
300S Series Technical specification, engines TECHNICAL SPECIFICATION, ENGINES Engine type Honda GX390 Kubota D 722 (petrol) (diesel) Function 4 stroke 4 stroke Cooling system water Number of cylinders Starter electric / manual electric Bore * stroke 88 * 64 mm 67 * 68 mm Displacement 389 cm... -
Page 10: Load Diagram
Tipping load No driver AVANT 320S /320S+ load diagram The diagrams can be interpreted as follows: • If the load is 25 cm in front of the attachment coupling plate, the max. load for the model 313S with 13 hp petrol engine is 310 kg for the loader with a driver weighing 80 kg. -
Page 11: Controls
300S Series Controls OPERATING CONTROLS Following picture shows the location of operating controls. The location and function of controls may be slightly different in different models, see following pages. 1. Control levers for drive and boom & tilt 10. Auxiliary hydraulics control lever (models 313S, and 320S) 2. - Page 12 Controls 300S Series CONTROL OF LOADER BOOM, ATTACHMENTS AND OTHER FUNCTIONS The control levers for driving, boom and bucket control, auxiliary hydraulics and telescopic boom (option) are mounted on the dashboard in front of the operator. On the following are the explanations for these functions.
- Page 13 300S Series Controls CONTROLS IN THE FOOTWELL The picture on the left shows the controls located in the footwell for models 313S and 320S: 1. Throttle pedal: Controls engine revs 2.Double speed pedal: Press the pedal down to engage double speed function 3.
-
Page 14: Starting The Engine
Starting the engine 300S Series STARTING THE ENGINE Petrol engine (Avant 313S, see also Honda engine Owner‘s Manual) • Turn the battery disconnect switch to ON • Turn the fuel valve to the on ON position (on the left side of the engine, see Honda Owner’s Manual) •... -
Page 15: Stopping The Engine
300S Series Stopping the engine NOTICE! The engine cannot start if the auxiliary hydraulics control lever is in locking position or the pump selection lever (on model 320S+) is in the position „2-pump“ (when the ambient temperature is low) STOPPING THE ENGINE •... -
Page 16: Double Speed Function
Operator’s Manual. If you are uncertain of the conduct of the machine please contact your AVANT On 320S+ the oil flow to auxiliary hydraulics depends dealer for instructions. -
Page 17: Coupling The Attachments
300S Series Coupling the attachments COUPLING THE ATTACHMENTS Coupling of the attachments into the attachment coupling plate happens as follows: Stage 1: • Lift up the two locking pins on either side of the attachment coupling plate and turn them backward so that they remain in the locked up position •... -
Page 18: 300S Series Service Table
Maintenance schedule 300S Series MAINTENANCE SCHEDULE Following table shows the maintenance and service points and intervals. There are more detailed instructions about each service operation, in numerical order, on the following pages. Every Every After After Every Every Every Every Every Every Every... -
Page 19: Safety Instructions For Maintenance
300S Series Safety instructions for maintenance SAFETY INSTRUCTIONS FOR MAINTENANCE ALWAYS REMEMBER SAFETY DURING MAINTENANCE DO NOT PERFORM ANY SERVICE OPERATION WHEN THE ENGINE IS RUNNING USE THE SERVICE SUPPORT ON THE BOOM CYLINDER DO NOT GO UNDER UNDSUPPORTED BOOM DO NOT SMOKE DURING SERVICE OPERATIONS BEWARE POSSIBLE HIGH PRESSURE IN HYDRAULIC CIRCUITS MOUNTING OF THE SERVICE SUPPORT... -
Page 20: Maintenance Instructions
Maintenance instructions 300S Series 1. CLEANING THE LOADER 5.CHANGING OF HYDRAULIC OIL FILTER Cleanliness of the loader is not only a question of The hydraulic oil return filter is located on top of the outer appearance. All surfaces, painted and others, hydraulic oil tank, under the cover. -
Page 21: Refueling
Measuring the hydraulic system pressure: System pressure is measured from the female auxiliary hydraulics quick coupling, with full revs and by turning AVANT 313S is equipped with the Honda GX390 the aux. hydraulics control lever. petrol engine. Service and maintenance instructions ATTENTION! It is recommended that pressures for this engine can be found in the Honda Operator’s... -
Page 22: Filter Location
Filters, greasing points 300S Series FILTERS Following pictures and tables show the location and part numbers for the filters. 1. Fuel filter A 44494 Filter kit 313S A 44495 Filter kit 320S and 2. Air filter 320S+ 64217 Air filter 3. -
Page 23: Troubleshooting
300S Series Troubleshooting TROUBLESHOOTING Services made Date Operating hours Remarks 1. _________ __________ ________________________________________________________________ 2. _________ __________ ________________________________________________________________ 3. _________ __________ ________________________________________________________________ 4. _________ __________ ________________________________________________________________ 5. _________ __________ ________________________________________________________________ 6. _________ __________ ________________________________________________________________... -
Page 24: Attachment Listing
Avant Tecno Oy Ylötie 1 FIN-33470 YLÖJÄRVI, FINLAND Tel. +358 3 347 8800 sales@avanttecno.com AVANT has a policy of continuing improvement, and retains the right to change specifications without notice. © 2018 AVANT Tecno Oy. Kaikki oikeudet pidätetään. www.avanttecno.com...
Need help?
Do you have a question about the 313S 2018 and is the answer not in the manual?
Questions and answers