Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yard force Y4GB A23 U001
Summary of Contents for Yard force Y4GB A23 U001
- Page 1 Model: Y4GB A23 U001 OPERATOR’S MANUAL PETROL BLOWER VAC WARNING! Read this manual carefully before use. Keep it in a safe place for future reference. Hotline:1300 418 640 Monday/Friday: 9.00am to 4.30pm Saturday: 9.00am to 3.00pm Email: service@actionspares.com.au...
- Page 2 Read this manual carefully prior to assembling and operating prior to assembling and operating. It is dangerous to operate this product without being familiar with these instructions. Keep this manual in a safe place and have it ready for future reference.
-
Page 3: Table Of Contents
Y4GB A23 U001 Operating Manual TABLE OF CONTENTS DESCRIPTION OF PRODUCT PARTS TECHNICAL SPECIFICATIONS INTENDED USE SAFETY INFORMATION INSTALLATION ADJUSTMENT OPERATION MAINTENANCE AND STORAGE TROUBLESHOOTING WARRANTY... -
Page 4: Description Of Product Parts
DESCRIPTION OF PRODUCT PARTS DESCRIPTION OF PRODUCT Parts description (Fig. A) Throttle 12. Impeller cover Upper handle 13. Primer bulb Air filter 14. Ignition switch Choke lever 15. Throttle lock Fuel cap 16. Combination wrench Fuel tank 17. Ratio fuel container Lower handle 18. - Page 5 DESCRIPTION OF PRODUCT PARTS Check the delivery parts Carefully remove the machine from its packaging and check as the following parts are complete (Fig. B): a. Main body b. Blower tube c. Dust bag d. Combination wrench e. Ratio fuel container f.
-
Page 6: Technical Specifications
TECHNICAL SPECIFICATIONS Model Y4GB A23 U001 Dimensions(L×W×H) 580x355x370mm Engine Type 1E34FN Cylinder Diameter 34mm Displacement 26cc Fuel Petrol/oil mixture 40:1 Carburetor Membrane type primer pump Way of ignition Spark plug RCJ6Y Starting Recoil starter Fuel Tank Capacity 500ml Weight 4.5kg Rated Power 0.7/7700 kW/r/min... -
Page 7: Safety Information
SAFETY INFORMATION Description of Symbols Symbols are used in this manual to attract your attention to possible risks. The safety symbols and the explications which accompany them must be perfectly understood. The warning themselves do not prevent the risks and can not be a substitute for proper methods of avoiding accidents. - Page 8 SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS Never allow children to use the blower. Beware of overhead power lines. Avoid operating while people, especially children, are nearby. Do not wear loose clothing or jewellery, which can be caught in moving parts. Use of sturdy gloves, non-slip footwear, safety glasses and earmuffs are recommended. Use extra care when handling fuels.
- Page 9 SAFETY INFORMATION WARNING! Proper safety precautions must be observed. Like all power equipment this blower must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this blower unless they are trained in its operation.
- Page 10 SAFETY INFORMATION to direct sunlight, high ambient temperature and damp, wet or high humidity conditions. Do not smoke or use a mobile phone while refuelling. This is potentially dangerous as it may ignite the fuel and cause an explosion. Take care not to spill fuel. When refuelling the blower ensure that the motor has been switched off.
-
Page 11: Installation
INSTALLATION ASSEMBLING BLOWER FUNCTION (FIG. C&D) Remove the M5x10mm screw from the boss on the main body with a screw driver. The upper blower tube baynets onto the main unit. Push and then turn the upper blower tube until it locks in position. Secure the upper blower tube with the M5 x 10mm screw. -
Page 12: Adjustment
ADJUSTMENT FUEL USE FRESH UNLEADED FUEL (PETROL), 90 OCTANE OR BETTER – Do NOT use E10 or Ethanol blends. Mix with a premium grade air cooled 2-Stroke oil at a ratio of 40:1 Mix fuel with 2-stroke oil in an approved container. Shake gently and ensure a thorough mix. - Page 13 ADJUSTMENT Remove the fuel cap...
-
Page 14: Operation
OPERATION STARTING THE BLOWER Set the ignition switch to the ON position "I". (Fig. I) Repeatedly press the primer bulb until it is full of fuel. This is not required for a warm engine. If the engine is cold, move the choke lever upwards to the ON position. This is not required for a warm engine. - Page 15 OPERATION from driveways or paths. Use full throttle when moving heavy loads. For ease of use the throttle hold lever on the handle can be engaged to hold the current throttle position. USING THE VACUUM Install the vacuum air tube and dust bag as described in the "Installation" section.
-
Page 16: Maintenance And Storage
MAINTENANCE AND STORAGE BEFORE EACH USE: Remove dirt and debris from the blower exterior. Inspect the engine, tank and hoses for possible fuel leaks, and repair as necessary. Inspect the engine cooling fins for accumulations of dirt or debris , and clean as necessary. - Page 17 MAINTENANCE AND STORAGE the blower until it stops from lack of fuel. LUBRICATION - Remove the spark plug and then pour approximately a tea spoon of 2 stroke oil into the cylinder through the spark plug hole. Before reinstalling the spark plug, pull the recoil starter 2 or 3 times to distribute the oil over the cylinder walls.
-
Page 18: Troubleshooting
TROUBLESHOOTING Starting Failure PROBLEM POSSIBLE CAUSE REMEDY No fuel in tank Fill fuel tank Press primer bulb 3-5 times until Fuel system not primed fuel system is full of fuel Choke not engaged Use choke when starting Engine fails to start Spark plug is fouled. -
Page 19: Warranty
WARRANTY WARRANTY This product is covered by a 1 year parts and labour warrant against manufacturing defects. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.