Page 1
FM30 / FM50 User Manual USER MANUAL “FM series” Fiber Laser Marking Machine...
Page 2
FM30 / FM50 User Manual Preface First of all, thanks for choosing and buying our CAMFive Fiber series laser marking machine. Your trust is the biggest support for us. In the following, the general instruction and basic application of the fiber laser marking machine will be introduced to you in several aspects.
Page 3
FM30 / FM50 User Manual As the input/output terminals, laser power supply, sound and light power supply, and control power supply, etc. may be charged, you must be careful while in use to avoid electrical shock. Please pay attention to personal safety! Optical fiber laser marking machine belongs to the fourth-class laser products, therefore, please wear protective glasses while using it.
Page 4
FM30 / FM50 User Manual lower downtime of examination and repair, but also improve the credibility and the working life of the machine. ◆ This manual includes industrial injury prevention and environmental protection. Users can adjust accordingly regarding their specific conditions. ◆...
FM30 / FM50 User Manual We suggest not to use it for long when the amperemeter is in the maximum state as it will break down laser power and shorten the life of the laser. Cut off the power immediately if there is a malfunction or an outbreak of fire. Do not operate or continue to operate the machine if you suspect there is any damage.
FM30 / FM50 User Manual Chapter One: Brief Introduction 1.1 Summary Optical fiber laser marking machine is a kind of professional laser marking equipment, which integrated light, machine, electricity, independent research and development, and production. The key components are imported. Our machine is with the advantage of novel style, unique structure, convenient operation, high-frequency modulation, high marking speed and precision, and stable performance.
FM30 / FM50 User Manual 1.2 Main Specifications Laser wavelength: 1064nm Laser power: 30W / 50W Modulation frequency: 20KHz-80KHz Scanning speed: ≤2000 to 7000mm/s Repeatability precision: 0.001mm Engraving range:100mmX100mm (optional 300x300mm) Marking depth: 0.01- 0.2 mm (Depending on the material) Marking line width: 0.01-0.2 mm (Depending on the material)
FM30 / FM50 User Manual Power supply: AC220V ±10%, 60 Hz, ≤0.8KW Safety: overcurrent protection, over-temperature protection, over-voltage protection Continuous Working hours: >23 Hours Chapter Two: Working principle and structure 2.1 Marking Principle * The laser light energy evaporates the material in the surface and shows lower material; * The laser light energy causes the surface chemical to change physically and "engrave"...
FM30 / FM50 User Manual 2.4 Control Section The front panel of the control cabinet: Laser power Scanner power Branch Power/Stop Air Switch Red Spot 2.5 Back Panel of the Control system The Terminal Blocks...
FM30 / FM50 User Manual Chapter Three: Installation Requirements & Operating Instructions 3.1 Equipment Installation Requirements Laser marking machine should be used in a clean environment when possible with 10 ℃-35 ℃. The optical device should be kept dry and clean. It is highly recommended a separate and closed workshop for this machine in order to assure a constant temperature indoor.
FM30 / FM50 User Manual The Outside of the Wiring Diagram AC220V/50Hz external input power,≥800W 3.2 Operation Process Instructions 3.2.1 Start Up Order ① Turn the air switch on ② Turn on the computer ③ Turn on the switch button for laser power in the front panel ④...
Page 16
FM30 / FM50 User Manual Adjust Current Frequency adjustment within range 20-80 kHz. In most situations, consider adjusting to 20 kHz. ⑥ Adjust the focal length for marking. Adjust the height of the lifting worktable. Keep the distance as the shown picture. The distance should be adjusted to 215mm (±10mm).
FM30 / FM50 User Manual 3.2.2 Sequence of Shutting the Equipment Down ① Adjust current to the minimum (this can effectively reduce the impact on laser module) ② Turn off laser power supply switch ③ Turn off scanner power and the red light power in the front panel. ④...
Page 18
FM30 / FM50 User Manual 4. Laser beam path should be closed as far as possible in case the laser is leaked. 5. The fan must be checked if it is working correctly after being started up. 6. Use professional paper to wipe the lens clean. After wiping the lens, please wait for the alcohol to be completely volatilized before installation.
FM30 / FM50 User Manual 4.2 Maintenance Cleaning Optical Lens Because of the working environment, the optical lens may have been polluted after being used for a period of time. If it is not maintained regularly, the dust will corrode the lens with coating.