Onward 1463658 Instructions For Installation Or Replacement

Instructions for Installation or Replacement of Commercial Lockset
For use on doors 1-3/8" to 1-3/4" (35 mm to 45 mm) thick
Instructions pour l'installation ou le remplacement de serrures à usage commercial
Pour portes de 1-3/8 po à 1-3/4 po (35 mm à 45 mm) d'épaisseur
Mounting screws /
Vis de montage
Inside rose /
Rosette
Inside knob /
Poignée intérieure
1. New door preparation / New door preparation
a. Fold template over edge of door and
mark holes.
b. Drill 2-1/8" (54 mm) hole through face
of door. Drill from both sides to avoid
damaging door.
c. Drill a 1" (25 mm) hole in edge of door.
d. Drill 5/32" (4 mm) notches on the 2-1/8"
(54 mm) hole on both sides of door.
e. Mortise latch unit front 2-1/4" x 1-1/8"
x 1/8" (57 mm x 25.4 mm x 4 mm).
a. Fold template over edge of door and
mark holes.
b. Drill 2-1/2" (54 mm) hole through face
of door. Drill from both sides to avoid
damaging door.
c. Drill a 1" (25 mm) hole in edge of door.
d. Drill 5/32" (4 mm) notches on the 2-1/8"
(54 mm) hole on both sides of door.
e. Mortise latch unit front 2-1/4" x 1-1/8"
x 1/8" (57 mm x 25.4 mm x 4 mm).
3. Install lock body / Install lock body
a. Install latch and secure with provided screws.
b. Slide lock body into door and ensure that latch prongs engage lock body.
a. Install latch and secure with provided screws.
b. Slide lock body into door and ensure that latch prongs engage lock body.
1
Latch /
Loquet
4. Install inside knob / Install inside knob
a. Install mounting plate and secure with
mounting screws.
b. Screw inside rose onto spindle until
hand tight.
c. Push inside knob all the way onto
spindle until it clicks into catch hole.
d. Auto-release turn button is standard.
Deadlock turn button also available (press
the turn button and rotate 90° clockwise).
a. Install mounting plate and secure with
mounting screws.
b. Screw inside rose onto spindle until
hand tight.
c. Push inside knob all the way onto
spindle until it clicks into catch hole.
d. Auto-release turn button is standard.
Deadlock turn button also available (press
the turn button and rotate 90° clockwise).
Mounting plate /
Plaque de montage
Sleeve (For 1" (25 mm) hole) /
Sleeve (For 1" (25 mm) hole)
Inside knob cover /
Inside knob cover
Notch / Notch
4 mm wide / wide x
4 mm high / high x
4 mm deep / deep
Backset / Écartement
70 mm
Center line /
Ligne centrale
Outside rose /
Rosette extérieure
Latch /
Loquet
2
Outside knob /
Poignée extérieure
Body / Body
Mounting plate /
Plaque de montage
Lock body /
Mécanisme principal
Inside knob /
Poignée intérieure
Inside rose /
Rosette
Outside knob cover /
Outside knob cover
Outside rose /
Rosette extérieure
Lock body /
Mécanisme principal
Catch (retainer) /
Catch (retainer)
Latch /
Loquet
Combination screw /
Combination screw
2. Remove inside trim and adjust / Remove inside trim and adjust
a. Use push pin to depress knob catch and pull off inside knob. Then remove inside rose and
mounting plate.
Mortise /
Mortaise b. Turn outside rose to adjust center line of lock body to match the center line of the door.
a. Use push pin to depress knob catch and pull off inside knob. Then remove inside rose and
mounting plate.
b. Turn outside rose to adjust center line of lock body to match the center line of the door.
Inside rose /
Rosette
Inside knob /
Poignée intérieure
Changing direction of keyway / Changing direction of keyway
Keyway direction is normally in down position. To change the direction:
a. Turn key 75° clockwise, insert push pin into catch hole to depress knob catch. Pull outside
knob off of spindle.
b. Turn knob 180° and then reinstall knob.
Keyway direction is normally in down position. To change the direction:
a. Turn key 75° clockwise, insert push pin into catch hole to depress knob catch. Pull outside
Latch tail /
Latch tail knob off of spindle.
b. Turn knob 180° and then reinstall knob.
Slide /
Slide
Latch prongs /
Latch prongs
5. Install strike / Install strike
Strike box /
Strike box
Strike /
Gâche
Center line /
Ligne centrale
Outside knob /
Poignée extérieure
Push pin /
Push pin
Cylinder assembly /
Cylinder assembly
Tools Required
• 1 Phillips head screwdriver
• 1 hole saw - 2-1/8" (54 mm)
• 1 drill bit - 1" (25.4 mm)
• 1 drill bit - 5/32" (4 mm)
• 1 chisel
Strike / Outils requis
Gâche
• 1 Phillips head screwdriver
• 1 hole saw - 2-1/8" (54 mm)
• 1 drill bit - 1" (25.4 mm)
• 1 drill bit - 5/32" (4 mm)
• 1 chisel
Mounting plate / Center line of the door /
Plaque de montage Center line of the door
Catch /
Catch
1
2
Push pin / Center line /
Push pin Ligne centrale
Catch hole /
2
Catch hole
Outside knob /
Poignée extérieure
Push pin /
Push pin
3
Jamb /
Jamb
Latch /
Loquet
Door /
Porte
After door is closed, deadlocking plunger is retracted /
After door is closed, deadlocking plunger is retracted
Key /
Clé
1