Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Parker EXACTOL 400 Series
Summary of Contents for Parker EXACTOL 400 Series
- Page 1 Parker 400 Series Tube Benders Bulletin 4391-B400S...
-
Page 2: Table Of Contents
Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the “Offer of Sale”. -
Page 3: Introduction
Along with the bender itself, Parker has developed a complete package of accessories to enable this tool to be used for all types of bending: close bend radius blocks, mandrels for thin wall tubes, bench mounting adapters and more. -
Page 4: Parts And Accessories
Center drive shaft and worm also be mounted in an adapter unit and fastened to a gear shaft are supported with pre-lubricated ball bear- workbench. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd... -
Page 5: Radius Blocks
Triple-Lok and Ferulok tube fitting nuts. With the use of two Allen-headed screws in back of plate to provide space Parker’s Seal-Lok close bend adapter, one can also use for the larger radius blocks. Seal-Lok fittings with a close bend radius block. They permit an operator to make his first bend very close to the end of the tube. -
Page 6: Medium To Heavy Wall Tube Bending
(see diagram). On long lengths of tubing, support is recommended to prevent sag and to help keep tubing aligned with the radius block centerline. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd... - Page 7 Bends from 90° to 180° — The 400 Series Tube Benders bend tubing up to 180° with ease. The procedure for bends over 90° is the same as for bends to 90°. See Step 4. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd...
-
Page 8: Thin Wall Tube Bending With Mandrel Equipment
(in.) Type 0.283 to 0.362 520506 solid 5/16 0.363 to 0.484 520507 solid 520508 13/32 0.485 to 1.489 solid Mandrel To order mandrel rods, specify mandrel rod size and mandrel type. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd... - Page 9 However, extremes in either direction may cause wrinkling, breaking, or flattening of the tube. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd...
- Page 10 Then, to remove the tube, slide it out to the left, back along the axis of the mandrel assemble. Loosen the mandrel assembly if necessary to facilitate tube removal. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd...
-
Page 11: Model 412 Parts Schematic
Drive Screw, P.K. 13050 type “U” #0 x 1/8 Crank Handle 550612 Subassembly Worm & Shaft 550601 Subassembly (2-7) Worm Gear 550587 Dowel Pin 13021 Crank Handle 13502 Knob 13054 Shoulder Screw 13055 Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd... -
Page 12: Model 424 Parts Schematic
Drive Plate 13159 Key, 1/4 sq. x 19/32 13160 Washer 621070 Washer 621070 Dowel Pin 5/8 13163 Vise Jaw Adapter 13165 Dowel Pin 1/4 13166 Crank Handle 13168 Knob 13054 Screw 13055 Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd... -
Page 13: Bender Kits
Size 8 Radius Block 550583 Size 10 Radius Block 550584 Size 12 Radius Block 621047 Size 16 Radius Block 621049 Size 20 Radius Block 870149 Size 24 Radius Block — No carrying case available. Parker Hannifin Corporation Tube Fittings Division Columbus, OH www.parker.com/tfd...
Need help?
Do you have a question about the EXACTOL 400 Series and is the answer not in the manual?
Questions and answers