Download Print this page

paasche F910-2 Operating Instructions & Replacement Parts

Automatic humidifier unit (2 spray heads)

Advertisement

Quick Links

F910-2
Automatic Humidifier Unit
OPERATING INSTRUCTIONS & REPLACEMENT PARTS
F910-2
Cubic Feet, maximum output 30 Gallons (227 l) in 24 hours.
INTRODUCTION:
For dependable moisture and humidity control, these units provide an efficient method of maintaining uniform moisture
in paper, fabric, tobacco, etc. at the same time helping to reduce the possibility of fire hazards. The water is finely
atomized and quickly absorbed into the room atmosphere. Each Automatic Spray Atomizer requires 1 C.F.M. at 50
p.s.i. air pressure for the finest uniform atomization. Incoming shop air must be 80 PSI or higher. Regulator on unit
can be set to 45 to 60 PSI.
FIRE PREVENTION:
Paasche Humidifier Units present an inexpensive means of reducing the danger of spontaneous combustion. Proper
humidification limits dust diffusion and grounds static electricity.
HUMIDIFIER USES:
• Printing and Bindery Plants- They are of great value for keeping paper quality at its best to assure perfect
registration when printing.
• Tobacco and Similar Industries- require uniform humidity control when aging and curing.
• Textile Mills, Clothing Factories, Warehouses- Fabrics tend to gradually deteriorate in dry atmosphere. When
adequate humidity is maintained, goods retain their original luster and sheen. Dangers from lint and dust accumulations
are greatly minimized with proper humidity.
• Carton Manufacturers- Winter conditions can dry out materials used to make boxes, causing tears and improper
folding during manufacture or damage by the customer while in use.
• Dry and Dusty Factories- Factories which are dry and dusty due to insufficient humidity, are constantly subject
to the dangers of spontaneous combustion. One method of reducing this hazard is with a uniform, accurate and
dependable Automatic Humidifier Unit by Paasche.
The F910 & F930 Series Automatic Humidifier Units will automatically dispense gallons of finely atomized water,
providing controlled humidity when the dial on the humidistat (Item #1) is adjusted to the humidity required. These
Automatic Humidifier Units will automatically start and stop at the humidity setting. When properly connected to
the water and electric systems of the building and to an air source that supplies constant air pressure (minimum
50 p.s.i.) to the F910 & F930 Series Unit, these units will deliver finely atomized water for extended periods.
Paasche Airbrush Co.
9511 58th Place
Kenosha, WI 53144
Phone: (800) 621-1907
Website: www.paascheairbrush.com
E-Mail: info@paascheairbrush.com
(
2 Spray Heads)
Automatic Humidifier (Two Spray Heads) Capacity - 30,000
........Available with (4) Heads...(
Manual For F910-2 2/1/2018
WARNING:
This product must be grounded to
prevent electrical shock. Proper use of the three
wire grounding cord installed with each unit is
essential for its safe use. The plug must be plugged
into an outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
This unit is designed for the spraying of water only.
D i s c o n n e c t p o w e r b e f o r e s e r v i c i n g .
F930-4
)........
Printed in the U.S.A.

Advertisement

loading

Summary of Contents for paasche F910-2

  • Page 1 Incoming shop air must be 80 PSI or higher. Regulator on unit can be set to 45 to 60 PSI. FIRE PREVENTION: Paasche Humidifier Units present an inexpensive means of reducing the danger of spontaneous combustion. Proper humidification limits dust diffusion and grounds static electricity. HUMIDIFIER USES: •...
  • Page 2 F900 PAASCHE - Series Automatic Humidifier HUMIDIFIER INSTALLATION F910-2 UNIT 1. Mount Humidifier Unit in convenient location using Mounting Bracket (not shown). 2. Connect air supply to HF-1/4” Air Inlet Valve. 3. Connect water supply to HF-1/4” Water Inlet Valve.