Geekoto C1 Operation Instruction Manual
  1. Manuals
  2. Brands
  3. Geekoto Manuals
  4. Camera Accessories
  5. C1
  6. Operation instruction manual

Geekoto C1 Operation Instruction Manual

(commander) flash trigger
Hide thumbs Also See for C1:
Table of Contents

Advertisement

Quick Links

Download this manual
C1 (Commander) Flash Trigger
Operation instruction
Fit for Nikon

Advertisement

Table of Contents
loading

Related Manuals for Geekoto C1

Summary of Contents for Geekoto C1

  • Page 1 C1 (Commander) Flash Trigger Operation instruction Fit for Nikon...

  • Page 2: Table Of Contents

    Catalog Safety instructions Function List Components Component instruction Preparation before use Functions description Custom function/FN Wireless channel setting Assisted focusing light Hot Shoe Nikon master control mixed mode Nikon master control Multi mode Specification List...

  • Page 3: Safety Instructions

    Safety instructions Function List Please read this manual carefully before use. 1.Available flash mode: I-TTL, M, Multi. 2.Available for Front curtain sync/back curtain sync/ 1.Please turn off all devices while you connecting them to each other. high-speed sync, highest sync speed 1/8000s. 2.Please prevent dropping hand shaking intensively 3.Exposure compensation available.

  • Page 4: Components

    Components Components Group C Setting (up/down/ Rubber cap Mode left/right) Group D/Channel setting Micro USB Test Power switch: ON/OFF Battery door Group B Indicate light Setting/restore factory setting Twist lock Group A/ Custom function setting LCD Screen Mounting holder...

  • Page 5: Component Instruction

    Components Component instruction Power Switch: LCD Screen Slide to 【ON】 to power on. Slide to 【OFF】 to power off Automatic focusing assist Flash setting for C Flash setting for D High-speed sync Focal Distance Manual /strobe flash mode Wireless channel Aperture Flash setting for A Strobe flash...

  • Page 6: Preparation Before Use

    Component instruction Preparation before use Hot Shoe contacts: Use it to connect with camera, Battery loading compatible with Nikon. Open the battery hatch. Install two AA batteries according Mode: Transmitter mode option to the positive and negative directions of the battery, Test: Send flash signal for groups when installation completed, close the battery hatch.

  • Page 7: Functions Description

    Preparation before use Functions description Power on Install the trigger on the hot shoe contact 【 】 from top of camera. Load batteries correctly, push the switch to turn on the trigger, then LCD screen & 2 color lights are on simultaneously, system check and complete initialization, enter standby mode, red indicator flashing.

  • Page 8: Custom Function/Fn

    Wireless channel setting Custom function/FN Press 【D】button about 2 seconds, wireless channel Press 【FN】for 2 seconds, system will change light flickers and enters wireless channel setting, between customized settings and flash modes, enter press 【←】/【→】to set channel from 1 to 16. custom mode, press 【←】/【→】to set option number.

  • Page 9: Assisted Focusing Light

    Assisted focusing light Hot Shoe If you enabled “automatic focusing”on transmitter, Connecting trigger with Nikon Cameras, Press the When the light is not enough to focus automatically, shutter lightly, trigger will identifies the camera it will enable the assist focusing light in trigger to help automatically, and send the trigger setting status to to make focusing easier.

  • Page 10: Nikon Master Control Mixed Mode

    Nikon master control mixed mode Nikon master control mixed mode Setting for groups ③ After selected a group, press 【MODE】button to ① Press【MODE】button to select transmitter mode set the flash mode of the group,every modes parameters are as below: as Nikon master control Mixed mode (as pic showed) TTL : Compatible with i- TTL , Exposure compensation adjustment available from -3.0EV to +3.0EV, total 22 levels;...

  • Page 11: Nikon Master Control Multi Mode

    Nikon master control Multi mode Nikon master control Multi mode ② Under non-grouping setting status, press 【←】/ Setting for groups 【→】button to set flash power, flash output is ① Press【MODE】button to select transmitter mode adjustable from 1/4 to 1/128, total 6 levels. as pic showed .

  • Page 12: Specification List

    Specification List Nikon master control Multi mode ⑥ After you select the setting groups, press【MODE】 System mode: Digital FSK 2.4G HZ Wireless Trigger button to turn on/off the groups you selected, you can Communication Distance: 50 meter also press 【← 】/【→ 】to turn on/off it, press Wireless Channel: 16 【↑】/【↓】button to change Focal distance for Flash mode: I-TTL, M, Multi.

Table of Contents