Table of Contents
Advertisement
Quick Links
English
construction B35
Configuration manual
electronic overspeed switch
®
EGS
41
®
EGS
(H)41
certificated according IEC 61508 SIL2 and DIN EN ISO 13849-1 PL d
Read the configuration manual prior to assembly,
starting installation and handling!
Keep for future using!
Translation of the original configuration manual
ID 74513
hollow shaft design
issued November 2018
Advertisement
Table of Contents
Related Manuals for Hubner EGS 41
Summary of Contents for Hubner EGS 41
- Page 1 English construction B35 hollow shaft design Configuration manual electronic overspeed switch ® ® (H)41 certificated according IEC 61508 SIL2 and DIN EN ISO 13849-1 PL d Read the configuration manual prior to assembly, starting installation and handling! Keep for future using! Translation of the original configuration manual issued November 2018 ID 74513...
- Page 2 Configuration manual EGS(H)41 Trademark ® is a registered trademark of Johannes Hübner Fabrik elektrischer Maschinen GmbH. ® Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Protected trademarks bearing a ™ or ® symbol are not always depicted as such in the manual. However, the statutory rights of the respective owners remain unaffected.
-
Page 3: Table Of Contents
Configuration manual EGS(H)41 Directory 1 Setting up ........................5 Planning and configuration ......................5 System requirements ........................5 Installing the software ......................... 6 Installing the driver manually ...................... 7 2 Configuring ........................9 Fundamental procedure ......................9 Configuration planning table ..................... 10 3 Software description .....................11 Head section .......................... - Page 4 Configuration manual EGS(H)41 11.3 Slip angle detection ........................28 11.4 Diagnostics output ........................28 12 Index ..........................29...
-
Page 5: Setting Up
Configuration manual EGS(H)41 This document tells you how to adjust the program settings for EGS(H) 41 with the EGS41Pro soft- ware and transfer them to the device. PLEASE NOTE! The documentation and the dimensional drawings will be copied in the installation folder in PDF format by the installation. -
Page 6: Installing The Software
Configuration manual EGS(H)41 1.3 Installing the software Ensure the EGS(H) 41 device and your notebook/PC are connected via the USB cable. Close the automatically started „Found new hardware wizard“ with a click on “Cancel“. Place the supplied CD containing the software into the CD drive or, alternatively, download the Set- up.exe. -
Page 7: Installing The Driver Manually
Configuration manual EGS(H)41 1.4 Installing the driver manually PLEASE NOTE! You must log into a user account with administrator rights to install the software. Ensure all programs are closed. If it is necessary to install the driver manually, depending on your operating system, please check the following steps. - Page 8 Configuration manual EGS(H)41 Newer Windows versions: Now select the installation source via “Browse” and point to path of your installation, there select the folder drivers. The Installation begins with a click on Next. The following illustrations are for Windows XP Sp3 and newer Windows versions. Windows XP Sp3: Newer Windows versions: Click Next, the installation of the driver software for this device has been completed.
-
Page 9: Configuring
Configuration manual EGS(H)41 2 Configuring In this chapter you will learn how to configure the EGS(H) 41 using the configuration software EGS41Pro. For the purpose of clarity the user interface is divided up into different sections. The drawing below offers a schematic overview: ... -
Page 10: Configuration Planning Table
Configuration manual EGS(H)41 2.2 Configuration planning table PLEASE NOTE! A configuration planning table is provided below. Use a printout or a copy of the planning table below to plan the configuration of the EGS(H) 41. Parameter Factory setting New value User device designation Inverse speed alignment Not active... -
Page 11: Software Description
Switch on the power supply to your EGS(H) 41. To launch the software EGS41Pro click 'Start \ Programs \ HUEBNER –GIESSEN \ EGS 41. When launching the software for the first time a window is displayed containing the licensing agree- ment. -
Page 12: Head Section
Configuration manual EGS(H)41 The individual functions on the “Home screen” are described in more detail in Chapter 3.1. To establish a connection to the EGS(H) 41 proceed as follows: On the Home screen click the 'Establish connection' button. Communications have been successfully established when the communication status symbol rotates. You can now begin to configure the device. -
Page 13: Information Section
Configuration manual EGS(H)41 3.2 Information section Information from the connected EGS(H)41 is displayed in the information section. The previously mentioned dynamic indicator symbolizing the communication status between the PC and the EGS(H)41 is displayed in the middle. Each successfully transmitted or received data packet causes the partial ring to rotate. -
Page 14: Establishing A Connection And Logging On
Configuration manual EGS(H)41 The reason why the switch symbol is highlighted red is because the switch is either defective or not connected correctly. The number of hours [h] in operation and the PCB temperature of the connected device is displayed below the switch symbol. When a switch is inactive it appears dimmed. -
Page 15: Parameters 1
Configuration manual EGS(H)41 Changes are made to the settings of the EGS(H)41 on the pages Parameters 1 and Parameters 2. On the Operating data page you are able to view a collation of all of the device settings and print these out for documentation purposes. - Page 16 Configuration manual EGS(H)41 CAUTION! When switch delay is activated the actual switch-off speed is higher than the set switch- off speed! Observe also information on determining the switching deviation described in the Operat- ing and Assembly instruction EGS(H)41! After making changes to the switching speed settings click the 'Check input' button to check the new settings do not violate restrictions.
- Page 17 Configuration manual EGS(H)41 You will again be required by a security prompt to verify and confirm your changes. Click the 'Confirm' button to confirm the changes you have undertaken and store these permanently in the connected device. To reject the changes click the 'Reject' button. The data in the temporary memory will be deleted.
-
Page 18: Inverse Rotation Evaluation
Configuration manual EGS(H)41 4.1 Inverse rotation evaluation Clockwise rotation for the switches S1R and S2R is defined as anti-clockwise rotation when viewing the end of the shaft of the EGS(H)41. When inverse rotation evaluation is activated the allocations for S1R and S1L are inverted. 4.2 Underspeed Underspeed is detected. -
Page 19: Parameters 2
Configuration manual EGS(H)41 5 Parameters 2 On this page the settings are made that define the safety-relevant characteristics of theEGS(H)41. 5.1 Broken wire detection Broken wire detection is available for the switching outputs S1 and S2. Detection is triggered as soon as the internal load current monitoring measures less than 5 mA when a switch is closed. -
Page 20: Delete Errors
Configuration manual EGS(H)41 PLEASE NOTE The password on delivery of EGS(H) 41 is “huebner”. Please note that you must enter a new password to protect the configuration from unau- thorized changes! When the factory-set password is changed the padlock symbol at the top of the screen is displayed closed. -
Page 21: Monitoring Screen
Configuration manual EGS(H)41 6 Monitoring screen These pages are available to all users, as they do not permit any changes to the device settings. Here you will find a graphic user interface based on the functions of an oscilloscope, for observation and analysis of EGS(H) 41's switching behaviour. -
Page 22: Functions
Configuration manual EGS(H)41 6.1 Functions Representation scaling: The input fields for entering values to adapt scaling are located on the right-hand side of the speed graphic. By entering the appropriate values in the 'Ymax' and 'Ymin' fields you can limit representations in the speed range. -
Page 23: Operating Data
Configuration manual EGS(H)41 7 Operating data Here you can see a summary overview of all settings for the connected EGS(H) 41. No settings can be adjusted here. The top section shows all major device settings and the parameters adjusted under “Parameter 2” with their current values. -
Page 24: Pulldown-Menu "File
Configuration manual EGS(H)41 8 Pulldown-Menu “file” With “Export” device data can be saved in the PC and with “Import” device data can be transferred from the PC to the device. 8.1 Save monitoring data “File Export Monitoring data” saves the recorded monitoring data (*.s41) in the PC. With “file ... -
Page 25: Pull-Down-Menu "Settings
Configuration manual EGS(H)41 9 Pull-down-Menu “Settings” Here, system settings can be changed. 9.1 Reset Password Is an selected user password lost, you can request by telephone via the menu item “Reset Password” a reset code. With this code the device can be reset to “factory setting”. CAUTION! By the function “Reset Password”... -
Page 26: Boot Loader Firmware
Configuration manual EGS(H)41 Boot loader firmware With the function “boot loader firmware” the device firmware can be replaced via the USB port. The boot loader is only available from version EGS41 1.07.00. To perform an update, you have to inform the manufacturer about the serial number of the device, an email address and recipient´s name. -
Page 27: Error Table
Configuration manual EGS(H)41 10 Error table Error message Description Dg_Intern Device error [FFxx] Dg_Iov Overcurrent in the switch 1 or switch 2 [0601, FE01 Dg_Sw1Dr Broken wire switch 1 [0602, FE02] Dg_Sw2Dr Broken wire switch 2 [0603, FE03] Dg_TempMain Overtemperature in device [0604, FE04] Dg_TempKK Overtemperature in switch... -
Page 28: Notes On Configuration
Configuration manual EGS(H)41 11 Notes on configuration It is only possible to configure the device with a single password (user rights: administrator). The facto- ry-set administrator password is: huebner. For reasons of safety it is strongly advised that you create a user-defined password (max. - Page 29 Configuration manual EGS(H)41 12 Index Configuration planning table Notes on configuration Configuring Operating data Delayed overcurrent switch-off Diagnostics output Parameters 1 Directory Parameters 2 Display section Planning and configuration Error table Rotation direction dependent switching Establishing a connection and logging on Setting up Functions Slip angle detection...
Need help?
Do you have a question about the EGS 41 and is the answer not in the manual?
Questions and answers