NTRODUCTION DANGER – Failure to follow these warnings and instructions may result in serious injury. Proper assembly, installation, use, and supervision are essential for proper operation and to reduce the risk of serious injury. Check inside both boxes and packaging materials for parts. Before beginning assembly, read all instructions and identify parts using the parts list.
ARTS Check inside both boxes and packaging materials for parts. Before beginning assembly, read all instructions and identify parts using the parts list below and on the next two pages. All chair parts are labeled with an Item #. It is critical that all parts be carefully inspected by the installer prior to installation to ensure that no cracking or warping occurred in transit and that a damaged part is not used.
SSEMBLY NSTRUCTIONS OOLS EQUIRED QUALITY Do not use power tools when assembling • #2 Square Drive Bit the lifeguard chair. Driving screws (34) too • 5/32” Allen Wrench quickly may break them. • 7/16” Ratchet or Wrench 1. A SSEMBLE OTTOM Attach part (2) without S.R.
Finished Seat Bottom should look like shown. 2. A SSEMBLE Attach part (2) with S.R. Smith decal to part Attach part (7) to assembly using screws (34). (8) using screws (34). 2C. Seat Back Assembly should look like the pictures below when finished. 66”...
3. A SSEMBLE OOTRESTS First, assemble the 3 Step Subassembly. Attach part (45) to 2x part (50) using Attach 2x part (50) to part (44) using screws screws (34). (34). 3C. Attach part (1) to assembly using 2x screws Attach part (17) to assembly using screws. (34) Verify the 3 Step Assembly looks like below:...
Page 12
Repeat Steps 3A-3E for the second step assembly using parts (46) and (47) instead of (44) and (45) 3G. Repeat Steps 3A-3E for the first step assembly using parts (48) and (49) instead of (44) and (45). 66” Sentry Lifeguard Chair Instruction...
4. A SSEMBLE Next attach Footrest (1), Footrest Front (17), and Step Side (23) using Screws (4) as shown below. Finished Upper Footrest Assembly should look like the picture below. Next use the 4 assemblies to assemble the chair. 66” Sentry Lifeguard Chair Instruction...
5. A SSEMBLE Attach Seat Back Assembly, Seat Bottom Assembly, and Footrest Assembly to leg (42) as shown using nuts (35), washers (36), and bolts (37). Do Not Fully Tighten Nuts and Bolts Until Chair is Completely Assembled. Attach leg (40) to assembly using nuts (35), washers (36), and screws (37). Do Not Fully Tighten Nuts and Bolts Until Chair is Completely Assembled.
6. A SSEMBLE PACERS Flip the chair on its back and attach leg spacers (53) to both legs to assembly using screws (34). Do Not Fully Tighten Nuts and Bolts Until Chair is Completely Assembled. 66” Sentry Lifeguard Chair Instruction...
7. A TTACH IGHT Attach rear leg (43) to assembly using bolts (37), screws (34), nuts (36), and washers (35) as shown. Attach front leg (41) to assembly using bolts (37), screws (34), nuts (36), and washers (35) as shown. 66”...
8. A TTACH ASES AND ANDHOLDS Attach bases (54 with extra holes in front, 55=rear) to assembly using screws (34). Attach handholds to front base. Use pistol-grip clamps to hold to legs to align. 66” Sentry Lifeguard Chair Instruction...
8C. Continue to attach handholds with screws (34) into front legs. Keep pistol-grip clamps in place. 9. A TTACH RMRESTS UPHOLDER MBRELLA OUNT ROSS RACING Attach arm rests (31 and 32) using screws (34). 66” Sentry Lifeguard Chair Instruction...
Page 19
Attach braces (24) using screws (34). 9C. Attach cross braces (25) using nuts (35), washers (36) and bolts (37) as shown. 66” Sentry Lifeguard Chair Instruction...
Page 20
9D. Attach cross braces (26) using nuts (35), Attach cup holder (27) using screws (34). washers (36), and screws (37). Do Not Fully Tighten Nuts and Bolts Until Chair is Completely Assembled. 66” Sentry Lifeguard Chair Instruction...
Page 21
Attach umbrella mount (28) using screws Tighten all fasteners back (34). through assembly to ensure all hardware has been properly tightened. 66” Sentry Lifeguard Chair Instruction...
66” S NSTALLING THE ENTRY IFEGUARD HAIR Warning: Chair required to be anchored to deck when using umbrella. Warning: Do not lift 66” Sentry chair alone. Get assistance from one or two others. Recommended Anchor: We recommend anchoring with 316L stainless steel 3/8”-3 ¾” long wedge anchors.
#8 X 2" SCREW, #2 SQUARE DRIVE, 316SS 05-33-124 1/4 FLAT WASHER, 316SS 05-33-125 1/4-20 X 2.25” FLAT HEAD SCREW\ 05-33-123 1/4-20 CAP NUT, 316SS Included with SLGC-66-S in Box 1 OOLS EQUIRED • #2 Square Drive Bit • 5/32” Allen Wrench •...
Page 24
Slide support beneath chair. Rotate Attach support to chair with screws up so both sides contact the chair. (34). 66” Sentry Lifeguard Chair Instruction...