Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BBG KDAEC Series
Summary of Contents for BBG KDAEC Series
- Page 1 KDAEC Instruction Manual KD-AEC-en,V1.1-2011...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Additions (Interior Calibrate) 1. Enter the FACTORY PARAMETERS mode(see section 1.0 INTRODUCTION------------------------------1 twice, and 13.2~13.3),while the display show ”Pi”, Press the 2.0SPECIFICATIONS-----------------------------1 press the key three times, and then press the key four 3.0INSTALLATION--------------------------------3 times, the display will show “PASS”. 4.0 KEYPAD------------------------------------------4 2. -
Page 3: Introduction
1.0 INTRODUCTION 14.0 ERROR MESSAGES During the initial power-on testing or during the operation The KDAEC range of Platform Scales has a stainless steel top pan the scale may show an error message. The error on a steel frame and an indicator with a large backlit LCD. The messages are described below. - Page 4 13.2.4 STABILIZATION TRACKING Platform size This parameter is for setting the size of the tracking range to KDAEC(30kg/75kg/150kg) 390 x310 x 40mm indicate the stability. This is used to stable the scale once a KDAEC M (30kg/75kg/150kg/200kg/300kg) 500 x500 x40mm weighing result is achieved.
-
Page 5: Installation
To return to normal weighing, turn the scale off and back to on 3.0 INSTALLATION again or press the key. 3.1 UNPACKING The scales come with- 13.2.1 FILTER This parameter is for setting the speed of the display filter. For Standard KDAEC KDAEC M KDAEC L... -
Page 6: Keypad
3.3 SETTING UP USB print USB prints and the hold communication continuously. Hold occurs when is off Hold occurs occurs when the when the key is pressed. If key is pressed. pressed. Hold is pressed a second time Hold is released print will occur again. -
Page 7: Display
is set to “Hod 2” or “Hod 3”. 5.0 DISPLAY 1.Hti 0 : Holds the display for an infinite time limit 2.Hti 1 : Holds the display for 15 (1 x 15) seconds 3.Hti 2 : Holds the display for 30 (2 x 15) seconds 4.Hti 3 : Holds the display for 45 (3 x 15) seconds 5.Hti 4 : Holds the display for 60 (4 x 15) seconds Press the... -
Page 8: Auto Power Off
1.trn 1 : No data output 9.0 AUTO POWER OFF 2.trn 2 : Continuous data output The auto power off can be set by the user to disable the feature or to apre-set time interval. See setting of the parameter in section 3.trn 3 : Normal output when the key is pressed. -
Page 9: Usb Interface
10.3 TARING unit which is “lb”. After all units are set, press the key to Press the key to tare the scale. The weight that was move to the next parameter. displayed is stored as the tare value. This value is subtracted 13.1.4 COMMUNICATION ADDRESS from the display, leaving zero on the display. - Page 10 13.1.1 AUTO POWER OFF Normal OutputU: (See section 13.1.7) The first parameter is to set the auto power off function. The add: A display will show “Pr oFF” (DEFAULT SET). G/W: + 2.00 G/W is Gross Weight <cr><lf> to toggle between “Pr on” and “Pr oFF”. ...
-
Page 11: Calibration
Output format: Place the correct calibration mass as selected by the user at the centre of the pan. + 2.00 kg <cr><lf> + 1.00 kg <cr><lf> Press the . The display will return to weighing mode. + 1.00 kg <cr><lf>...