Advertisement
Quick Links
Item
Hampel Item Number
1
AH-110-1
2
AH-135-L
3
AH-135-R
4
AH-220
5
AH-151
6
CH-9225
10
AH-LUMBER-KIT
(includes below items)
AH-150-1
AH-LUMBER-002-1
AH-LUMBER-001-1
Tools Needed – To Assemble the Unit:
1. ¼" (6mm) Drill Bit
2. Drill
3. 5mm Socket
4. Ratchet
5. Helper(s)
Revised: 11/28/18 LIT-1412 Rev D
MultiMax Assembly Instructions
Optional Item –Lumber Kit
Hampel, W194 N11551 McCormick Drive, Germantown, WI 53022
Phone: 262-255-4540 Fax:262-255-9731
Bill of Material:
Description
Top Cap
Left Side
Right Side
Back Panel, W/Bedding Door
Knockdown Hardware Kit
Parts Kit, Warm Weather Latch
Wood & Hardware for Mounting Hutch
Bolts and Washers Kit for Mounting
Hutch
Runner, Multimax Base
Side, Multimax Base
Tools Needed – To Assemble the Latch:
1. 7/16" or 11mm Socket / Ratchet
2. 7/16" or 11mm Wrench
Qty
1
1
1
1
1
2
1
1
2
2
1
Advertisement
Related Manuals for Calf-Tel MultiMax
Summary of Contents for Calf-Tel MultiMax
- Page 1 Revised: 11/28/18 LIT-1412 Rev D MultiMax Assembly Instructions Bill of Material: Item Hampel Item Number Description AH-110-1 Top Cap AH-135-L Left Side AH-135-R Right Side AH-220 Back Panel, W/Bedding Door AH-151 Knockdown Hardware Kit CH-9225 Parts Kit, Warm Weather Latch Optional Item –Lumber Kit...
- Page 2 Revised: 11/28/18 LIT-1412 Rev D Step 1: Assembling the MultiMax A. First - Place the Left and Right Sides of the MultiMax on the ground standing upright approx. 60” (1524mm) apart. (as shown in the picture below) **Optional Method** Sides may be slightly warped due to shipment configuration. It may help to attach the two (2) sides to the wood base prior to assembling the MultiMax.
- Page 3 Revised: 11/28/18 LIT-1412 Rev D B. Next – Place the Top Cap onto the Left and Ride Sides…the sides may need to be adjusted so the Top Cap sits correctly. The ribs on the Top Cap should line up with the ribs on the sides.
- Page 4 Top Cap and use them to drill a hole thru the Sides. i. The rivet is inserted from the outside of the MultiMax and the backup washer is used on the inside of the MultiMax. (see detail below)
- Page 5 Revised: 11/28/18 LIT-1412 Rev D D. Next – Attach the Back of the MultiMax using the 1/4” (6mm) Rivets and Back Up Washers. Using the 1/4” (6mm) drill bit, locate the predrilled holes in the Back and use them to drill a hole thru the Sides.
- Page 6 Revised: 11/28/18 LIT-1412 Rev D Optional Item – Lumber Kit Step 1. Base Lumber Kit Lumber size: 2 pcs - 4” x 4” x 99.125” (101.6mm x 101.6mm x 2517.7) 2 pcs – 4” x 6” x 88.125” (101.6mm x 152.4mm x 2136.7) A.
- Page 7 Revised: 11/28/18 LIT-1412 Rev D Entrance Bracket Figure 2 locations Hampel, W194 N11551 McCormick Drive, Germantown, WI 53022 Phone: 262-255-4540 Fax:262-255-9731...