Subscribe to Our Youtube Channel
Summary of Contents for GE MaxOptix T5-2600P Star Series
- Page 1 GE MEDICAL SYSTEMS Technical Publication Direction 2233080 Revision 3 GE Medical Systems High Capacity MOD Option Installation Manual Copyright ©1999 by General Electric Company...
- Page 2 This page intentionally left blank.
- Page 3 Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual...
- Page 4 IMPORTANT! . . . X-RAY PROTECTION In performing all electrical work on these GE products, GE will The purchaser of GE equipment shall only utilize use its own specially trained field engineers. All of GE’s personnel (i.e., GE’s field engineers, personnel of third-...
- Page 5 Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual REVISION HISTORY REVISION DATE REASON FOR CHANGE 02/23/99 Initial Release 04/09/99 Changes per Design Review 11/20/99 Achieve Uniform Revision Numbers with Operator Addendum No Other Change 04/10/00 Added References to New MaxOptix Drive T5-2600P* Star...
-
Page 6: Table Of Contents
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual TABLE OF CONTENTS SECTION 1 - INTRODUCTION..........................1 PURPOSE..............................1 UPGRADE KIT CONTENTS.........................1 MANPOWER..............................1 PERFORMANCE CHECK ..........................2 WORK FLOW CHART ..........................4 DOCUMENTATION ............................5 SECTION 1 - REPLACING THE PIONEER DRIVE WITH THE MAXOPTIX DRIVE ..........6 SYSTEM SHUTDOWN ..........................6 REMOVING THE SCSI TRAY ........................6 REMOVING THE MOD DRIVE........................9... - Page 7 Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual LIST OF ILLUSTRATIONS ILLUSTRATION 1-1 Work Flow Chart ..............................4 ILLUSTRATION 2-1-A SCSI Tray Power Connector ...........................6 ILLUSTRATION 2-1-B RP Computer in CT HighSpeed Advantage RP1.X and RP2.X Systems ...............7 ILLUSTRATION 2-2 Removing the SCSI Tray ............................8 ILLUSTRATION 2-3-A Drive Locations on the SCSI Tray ...........................9...
-
Page 8: Introduction
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual SECTION 1 - INTRODUCTION PURPOSE The MaxOptix magneto-optical disk (MOD) drive, T5-2600P* Star, is being offered as an upgrade option to replace the current Pioneer MOD drive used in CT and MR Genesis-based systems. The current systems have one of the following Pioneer drives installed: DEUH7101, DEUH7001, DDM5101 and DDM5001. -
Page 9: Performance Check
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual PERFORMANCE CHECK 1. Perform archive functions using the Pioneer MOD drive installed in the system. Verify that all archive functions are working properly prior to installing the Maxoptix drive upgrade. 2. -
Page 10: Table 1-2: Intersystem Compatibility Matrix
: Intersystem compatibility matrix for Maxoptix magneto-optical disk drive. Top: CT Systems only Bottom: MR Systems only *Some CT/i and MR scanners will only support a certain size of media. Please check with your GE service engineer for drive and media compatibility. -
Page 11: Work Flow Chart
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 1-5 WORK FLOW CHART Check upgrade kit is complete (1-2) Save and restore one of each: exam, series, image to a media and view directly from the media and the system drive (1-4) Pre-existing Shut down the Genesis computer (2-1) problems? -
Page 12: Documentation
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 1-6 DOCUMENTATION The following documents are supplied with this kit: Title Direction # Maxoptix MOD Drive Replacement for 2233080-100 Pioneer Installation Manual High Capacity MOD Option User Guide 2233570-100 Addendum Table 1-3: Upgrade Documentation... -
Page 13: Replacing The Pioneer Drive With The Maxoptix Drive
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual SECTION 1 - REPLACING THE PIONEER DRIVE WITH THE MAXOPTIX DRIVE NOTICE Electrostatic Discharge (ESD) can damage electronic circuits. Do not handle any components without following the proper ESD precautions. SYSTEM SHUTDOWN The system software must be shut down (i.e. -
Page 14: Rp Computer In Ct Highspeed Advantage Rp1.X And Rp2.X Systems
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-2 REMOVING THE SCSI TRAY The SCSI tray is located in the top of the pedestal. To remove the SCSI tray: 1. With the power turned off as described under System Shutdown in Section 2-1. 2. -
Page 15: Removing The Scsi Tray
For MR systems that did not have the MOD drive option before, you may need to order mounting brackets GE P/N 46-306623P1 (right) and 46-306623P2 (left) in order to install the drive. You also need a dual opening bezel (front panel GE P/N 46-307621P1) if the current one has only one slotted hole. -
Page 16: Removing The Mod Drive
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-3 REMOVING THE MOD DRIVE NOTICE If working on an MR station where the drive is only an option, refer directly to section 2-4. If removing a full height WORM drive, care must be given to the wiring of the ribbon cable and the location of components in the SCSI tray: refer to page 10 for the procedure. -
Page 17: Illustration 2-3-B
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-3 REMOVING THE MOD DRIVE (CONTINUED) NOTICE Refer to this section only if REPLACING A WORM DRIVE. 1. Disconnect the cable from the Pioneer drive to the Optical Disk Controller Board situated in the back of the SCSI tray. -
Page 18: Installing The New Mod Drive
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-4 INSTALLING THE NEW MOD DRIVE SW1-8 SW1-1 Determining Drive Type: Top of the T5-2600P* Star Drive ILLUSTRATION 2-4 NOTICE Installation differs depending on the type of MaxOptix drive sent with the kit. Please follow the instructions below to determine which MOD drive you have. -
Page 19: Setting Drive Select Switches On Rear Of Drive T5-2600P* Star
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-4 INSTALLING THE NEW MOD DRIVE (CONTINUED) 5. Install the new screws and tighten. CAUTION Install the new drive with the screws included in the installation kit. Using the old screws will damage the new drive. -
Page 20: Table 2-1: Scsi Device Id Jumper Settings
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-4 INSTALLING THE NEW MOD DRIVE (CONTINUED) The SCSI device ID is set with jumpers on the jumper block (J7), pins 1 to 6 (refer to Illustration 2-5). See the table below. -
Page 21: Table 2-3: Maxoptix T5-2600P* Star Jumper Block Pin Assignments
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual The following tables pertain to Maoptix T5-2600P* Star only. The jumper block pin assignments for the Star drive are described in Table 2-3. Also check the global configuration settings from the top micro DIP switch block, as described in Table 2-4. -
Page 22: Firmware Verification
If installing a MOD drive in a computer which did not have this option before and whose front panel has only one opening, order a new bezel, GE P/N 46-307621P1, for installation. b. Remove all plastic positioning pins located on the tray cover above the MOD drive and tape or cartridge drive openings, make it flush with cover. -
Page 23: Systems Validation
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual 2-6 SYSTEMS VALIDATION 1. Insert a Maxoptix media in the drive. A Maxoptix media included in this kit with 512 BPS should be used. A 1024 BPS media will not work. 2. -
Page 24: Illustration 2-6-B
Direction 2233080, Rev 3 High Capacity MOD Option Installation Manual RATING PLATE Rating Plate Location for CT HiSpeed Advantage RP1.X and 2.X ILLUSTRATION 2-6-B...
Need help?
Do you have a question about the MaxOptix T5-2600P Star Series and is the answer not in the manual?
Questions and answers