Table of Contents
Advertisement
Quick Links
MODELS:
404 EH – Trailed with load arm and Automatic Control
404 M – Linkage mounted with cut and start, tipping facility and manual control
404 S -- Linkage mounted without cut and start or tipping facility
20/03/2015
Tanco Autowrap 404
TANCO AUTOWRAP
404 MINI BALE WRAPPER
OPERATORS HANDBOOK
WD03-404EH
1
Operators manual
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Tanco Autowrap 404
Summary of Contents for Tanco Autowrap 404
- Page 1 404 EH – Trailed with load arm and Automatic Control 404 M – Linkage mounted with cut and start, tipping facility and manual control 404 S -- Linkage mounted without cut and start or tipping facility 20/03/2015...
- Page 2 Tanco Autowrap 404 Operators manual GUARANTEE Subject to hereunder provided, the sellers undertake to correct either by repair or at their election by replacement any defect of material or workmanship which occurs in any of its goods within twelve months after delivery of such goods to first user, with the exception of contractors or commercial users when warranty period is six months.
-
Page 3: Table Of Contents
Tanco Autowrap 404 Operators manual USER’S MANUAL MINI WRAP 404 CHAP.CONTENTS PAGE INTRODUCTION SAFETY PRECAUTIONS GENERAL INFORMATION ON BALE WRAPPING SETTING UP / MOUNTING OF THE MACHINE MOUNTING OF PLASTIC FILM ADJUSTMENTS I USE OPERATION INSTRUCTION INSTRUCTIONS CONTROL BOX 14-19 PERIODIC MAINTENANCE 10.0 CHECK POINTS BEFORE TROUBLESHOOTING... - Page 4 Tanco Autowrap 404 Operators manual Fig 1.- 404 EH Model Roller End roller Tilt Frame Film Dispenser Cutter Drawbar Jockey wheel Wheel Load arm Squeeze arm 20/03/2015...
-
Page 5: Introduction
MINI WRAP 404 EH is hydraulically driven by the tractors hydraulic system, and is easy to operate with the RDS control box. The MINI WRAP 404 EH is designed to be a simple and effective bale wrapping machine square bales. -
Page 6: Safety Precautions
Operators manual SAFETY PRECAUTIONS. TANCO AUTOWRAP Ltd does not take the responsibility for damages that may occur on machine, persons or other equipment, because of the machine NOT being used as described in this manual, or because of the safety precautions NOT being followed. - Page 7 Operators manual DANGEROUS AREAS. TANCO AUTOWRAP Ltd has given the safety to the operator the highest priority, but it is still impossible to secure oneself of every danger area on the machine. Therefore we will now go through some of the dangers that can occur when using the Mini Wrap bale wrapper.
-
Page 8: General Information On Bale Wrapping
Tanco Autowrap 404 Operators manual GENERAL INFORMATION ON BALE WRAPPING. THE PRINCIPLE. The advantages of round bale ensilage are many, and include fewer feed units, a flexible harvesting system, large capacity and the possibility of selling feed units. In principle, the same fermentation processes occur whether the fodder is placed in a silo or pressed into bales and packed in plastic, i.e. - Page 9 Tanco Autowrap 404 Operators manual preferably under the outermost layer of plastic. Ensure that the hole is adequately sealed. The best wrapping results are obtained by... Harvesting the grass early..Drying it out to 30-40% solid content. If there is a danger of rain, bale and wrap the grass anyway.
-
Page 10: Setting Up / Mounting Of The Machine
If it is a 404 M or S machine, mount the 3 point linkage pins (attached to the chassis) Mount the loading arm and adjust the width on the lift arm in accordance with the bales diameter. -
Page 11: Mounting Of Plastic Film
Replace the locking bolt and the splint. The Tanco film Dispenser supplied with all 404 machine is capable of using several different sizes of film rolls. 500 mm, 360 mm and 250 mm plastic film can all be used but care must be taken that the correct level of overlap is used as you need turntable roller speeds for different films. -
Page 12: Adjustments I Use
Tanco Autowrap 404 Operators manual ADJUSTMENT / OPERATING. SUPPORT ROLLERS. Place the bale you want to wrap on top of the rollers. Move the support rollers as tight to the bale as possible. Make sure that the bale is in center of the rollers. -
Page 13: Operation Instruction
Lower the turntable down again. Then place a new bale on top of the rollers, and attach the film to the bale (404 S only), and start wrapping. Now the plastic film from the last should be cut off. Fasten the film end, if necessary, with some weatherproof tape. -
Page 14: Instructions Control Box
Tanco Autowrap 404 Operators manual 404EH CONTROL BOX 8.1-1 Functions MENU EXIT Display Reset Menu emergency stop Rotate auto. Knife open / Rotate man. close Table up/down Battery Fuse 10 Amp Connection Load arm cable cable up/down 20/03/2015... - Page 15 Tanco Autowrap 404 Operators manual Auto-wrap Controlbox 2000 404EH Notice: By pressing "EXIT" more than 3 sek. You allways will be braught back to "Wrap-cycle" ( Wrapp modus) By pressing "MENU" more than 3 sek, the display contrast will be adjusted. "MENY" up = Stronger MENY down = weaker Manual operation Behind the rubberplug on the the rear side of the control box it is placed a switch for manual/automatic operation.
- Page 16 Tanco Autowrap 404 Operators manual Actual RPM: Actual wrapping speed (Alarm limits :28-35) Alarm on 28 rpm Stop 35 rpm Balecounter SET: enter Reset possible ? Bales total for all 9 balecounters Bales machine total MENU: EXIT: SET: Reset Store...
- Page 17 Tanco Autowrap 404 Operators manual 4. Wrappingcycle Aktivited sensors a. Loading Loadarm down Loadarm rais and return back on sensor Table is hold in Table in loadposition loadposition b. Wrapping Start: Starts up on 1/2 Table down speed and runs...
- Page 18 Tanco Autowrap 404 Operators manual 2. Sensors Auto wrap 404EH Position loading. Signals to counter during w rapping Magnetic givers placed on the Un load sensor center axle. (below ) Sensor loadarm placed on frame Magnet placed on loadarm Lastearm down - sensor...
- Page 19 Tanco Autowrap 404 Operators manual THE INFRA-RED RECEIVER I TRANSMITTER SET. The receiver is connected directly to the machine junction box. The transition radius is stated at 30 meter. The actual radius may be as high as 60 meters depending on the battery condition. Sun filtered windscreens on the tractor will reduce the transmission distance further.
-
Page 20: Periodic Maintenance
Tanco Autowrap 404 Operators manual PERIODIC MAINTENANCE. BEARINGS. All ball-bearings are packed with grease, and do not need any more maintenance. DISPENSER. If the machine is in daily use, the guiding sleeves at the pre-stretcher should be oiled once a week or when needed. -
Page 21: Check Points Before Troubleshooting
Tanco Autowrap 404 Operators manual 10.0 CHECK POINTS BEFORE TROUBLE SHOOTING. In this chapter we have some general check points that have to be examined first if something is wrong with the machine. In chapter 11.0 we have a more detailed trouble shooting. -
Page 22: Trouble Shooting
Tanco Autowrap 404 Operators manual 11.0 TROUBLE SHOOTING. BEWARE OF MOVING PARTS WHEN TESTING THE MACHINE. 11.1 THE MACHINE DOES NOT WORK. The gage shows that there is enough pressure but there is no reaction from the machine. The problem can be that one or both of the quick couplers are not opening to let the oil through. - Page 23 Tanco Autowrap 404 Operators manual There are 3 basics which must ALWAYS be followed if the machine is to function correctly. 20/03/2015...
-
Page 24: Electric, Hydraulic Chart
Tanco Autowrap 404 Operators manual 12.0 HYDRAULIC CHART 20/03/2015... -
Page 25: Spare Parts List
Tanco Autowrap 404 Operators manual 13.0 OPEN / CLOSED CENTRE CONVERSION The conversion between closed and open center hydraulic system is carried out by the means of a 2 port solenoid valve, this is fitted in line in the pressure supply pipe to the main control valve.