Subscribe to Our Youtube Channel
Related Manuals for Arkel ARCUBE
Summary of Contents for Arkel ARCUBE
- Page 1 ARCUBE Quick Installation Guide Version : V1.01 ARCUBE MONOBLOCK LIFT CONTROL UNIT QUICK INSTALLATION GUIDE...
- Page 2 Arkel is not responsible for those mistakes that may be found in this manual and for the damages that they may cause.
-
Page 3: Table Of Contents
ARCUBE Quick Installation Guide Version : V1.01 CONTENTS ARCUBE MOUNTING .............................. 5 CONNECTIONS ................................. 5 .......................... 5 RAKE ESISTOR ONNECTIONS PTC C ......................5 OTOR HASES AND ONNECTIONS ........................6 ECHANICAL RAKE ONNECTIONS 2.3.1 Asynchronous motor brake connections ........................6 2.3.2... - Page 4 NSPECTION 11. ERROR CODES, POSSIBLE REASONS AND SOLUTIONS ................17 FIGURE LIST FIGURE 1 ARCUBE MECHANICAL SIZE ............................ 5 FIGURE 2 BRAKE RESISTOR AND BATTERY PACK SIZE (*) ....................... 5 FIGURE 3 MENU ..................................7 FIGURE 4 REQUIRED BRIDGING WHEN THE CAR TOP AND PIT INSPECTION NOT CONNECTED ..........7 FIGURE 5 REQUIRED BRIDGING WHEN THE CAR TOP AND PIT INSPECTION CONNECTED ............
-
Page 5: Arcube Mounting
ARCUBE Quick Installation Guide Version : V1.01 1. ARCUBE Mounting Mount ARCUBE monoblock unit, brake resistor, battery pack and UPS (If required). Figure 1 ARCUBE Mechanical Size Figure 2 Brake Resistor and Battery Pack Size (*) * These sizes are valid only if they are supplied by ARKEL. -
Page 6: Mechanical Brake Connections
ARCUBE Quick Installation Guide Version : V1.01 2.3 Mechanical Brake Connections 2.4.2 Synchronous motor encoder connections 2.3.1 Asynchronous motor brake connections 2.3.2 Synchronous motor brake connections 2.5 Motor Fan Connection 2.6 Battery Pack Connection (If necessary) 2.7 UPS Connection If you do not have UPS, you must bridge connectors U- 2.4 Encoder Connections... -
Page 7: Menu
“WITHOUT INSPECT BOX” parameters with “UP”, “DOWN” buttons. As you are on must be chosen. In the case of wrong choice, Arcube the parameter you wanted to enter inside, after pressing would not communicate with Fx-Cube board and raise an “ENT”... -
Page 8: Auto Tuning Parameter Settings
Motor control type screen. Motor control type must be chosen correctly as open Turn on all the fuses on ARCUBE, then turn on “SMP” loop or closed loop. switch over the distribution panel. After the screen is displayed, press “ENT” button in order to enter the menu. -
Page 9: Nominal Car Speed
ARCUBE Quick Installation Guide Version : V1.01 4.2.4 Nominal car speed 4.2.9 Motor direction This is the speed value what motor label shows. This parameter can be changed after completing auto tuning if the direction of move is wrong. 4.2.5... -
Page 10: Start Auto-Tune
Install the round magnet with black color side a little above the red color magnet. Take the “SEE” key on ARCUBE to “1” position and The distance between magnetic switch and magnets must keep pressing up or down recall buttons until “MOTOR be 1-2 cm. -
Page 11: Shaft Learning And Test Drive
6. Shaft Learning and Test Drive In encoder car positioning systems, before going to Figure 8 Installation of top round magnets for normal running operation, ARCUBE monoblock lift SKSR2 control unit must learn the shaft to learn the car position and shaft information. - Page 12 “UP” and “DOWN” buttons. This operation may take some time depending of the floor number of the elevator. ARCUBE screen shows in detailed in which process the shaft learning operation is. After ending of the shaft learning, the operation will be ended with the “SHAFT LEARN SUCCEED”...
-
Page 13: Call Settings
7.1 Car Calls 7.1.1 FX-Cube settings FX-Cube is a board used in ARCUBE system to be used for car calls. Each button inside the car is connected in options are existing. Select the correct parameter for your system over here. You may need to readjust “9.4: parallel to this board. -
Page 14: Landing Calls
(Not used as a call button), it is not necessary to system. Then, it is necessary to recognize the landing call perform this learning operation. buttons to ARCUBE. Press “LEFT” button until you see LOP learning screen. When you reach this screen, make 7.2.2 Parallel installation it “ENABLED”... -
Page 15: Software Update
Binary, 9. ARCUBE Peripherals These peripherals are all the units working on CANBus Inverted Gray, line. Each unit has its own address. After ARCUBE is updated, the other peripherals are looked for, then updated. 9.1 FX-Cube This is an inspection board located on the car top. It... -
Page 16: Enci
Car panel controller board. It is used for car calls (Socket) located on the control panel will not be functioning. If and it supports up to 16 floors in ARCUBE system. both pit and car top inspection terminals are taken to the inspection mode, both the “run”... - Page 17 ARCUBE Quick Installation Guide Version : V1.01 a) It is necessary to activate the reset key. All still get an error, the door contacts and 140 signal on the inspection/recall signals (868,869,870) must be active controller board needs to be checked.
- Page 18 The position of brake is monitored over KRC input. KRC If the motor PTC value is above the threshold level, this signal on ARCUBE needs to be checked. While the car error is raised. is in standstill position, it should be 24V. When the “5.24:...
- Page 19 In asynchronous machines, if there is no error with the open loop operation, encoder and ENCI board position, this error is raised. After the move command, “EN” input on ARCUBE connections need to be checked. should be 24V. While stopping, that signal should be cut.
- Page 20 ENCODER BOARD While the position of overspeed governor is monitored When the device couldn’t communicate with ENCA over the normally closed contact on ARCUBE, if an board, this error is raised. unexpected signal position is detected, this error is raised.
- Page 21 ARCUBE Quick Installation Guide Version : V1.01 problem with the phase sequence, this error is raised. L1 be set correctly. If the limit switches are not used, the parameters should be selected as “NOT USED”. Or limit or L3 phases need to be replaced with L2 phase.
- Page 22 H62: INSTALLATION ACTIVATION REQUIRED Installation activation of ARCUBE must be performed one-time. If you don’t it, the lift gives this error after 1 hour when it is in normal operation. This error will not occur on inspection or recall mode.
Need help?
Do you have a question about the ARCUBE and is the answer not in the manual?
Questions and answers
Password ka Ishu a raha hai
The context does not mention any specific password issue with the Arkel ARCUBE. It only explains that a username and password must be entered in the activation form, along with the device's serial number, to receive an activation code.
Therefore, no password issue is described.
This answer is automatically generated