Advertisement

INTRODUCTION
By selecting this device, you have acquired advanced active access-prevention technology.
With
we offer you an affordable system which guarantees operational reliability, top
BANDIT
performance and a discrete design.
More and more private and public buildings are being equipped with a protection system
against burglary. When armed, these systems detect a burglary attempt. The detection is
generally communicated by means of a siren and/or strobe or sometimes an automatic
phone call to an alarm control centre or police station. In real terms these notifications are
satisfying, but the subsequent human intervention often arrives more than 10 minutes
after the event! Burglars are aware of this and use this time to steal the most valuable
things and get away in time.
offers a unique and active solution to this problem. For this system is totally capable
BANDIT
of filling a large office, store or other room, within a few seconds, with a non transparent fog.
This fog prevents persons from entering the room for at least 10 minutes after setting off the
alarm, since they cannot see a thing. The ejected fog has a soft mint smell (to avoid possible
fire interpretation by outsiders), it is colourless and leaves no traces. So the fog safely and
quickly disables the vision capabilities of unwanted visitors.
is installed in those rooms that contain the most valuable objects; by doing so,
BANDIT
burglary damage is effectively limited to a strict minimum.
Advantages:
- Fills 28 m³ of space per second of fog expulsion.
- Extremely compact and discrete design.
- A system free of maintenance with very high operational reliability (by lack of moving
components).
- The standard integrated "Power saver" and good thermal isolation, maintains a very
low energy consumption, between 30 and 40 W/h, depending on the adjusted fog
expulsion period.
- Continuous control of liquid level. When the level is too low to guarantee a full
expulsion period it will be shown by an LED and an electrical contact will occur. In this
case you'll have to replace the internal HY-3 pack. The recognition and acceptance of
the new HY-3 pack (such as the resetting of the HY-3 shortage notification), occur
automatically. For recharging, the empty HY-3 pack has to be returned to your
dealer.
- In case of interrupted power supply voltage (230 VAC), operation is guaranteed:
electronics ~24 hours, fog generator ~2 hours.
- The PCB is equipped with 3 dipswitch blocks (with a total of 10 dips). It gives you the
possibility to easily program all elementary adjustments in a rather simple way without
the need of other adjustment devices, such as PC/laptop and/or adjustment links.
- The device is prepared through plug-in connectors, to be extended with a control box
and/or a wireless remote control.
- If mentioned while ordered, the device can be equipped with additional options, such
as: straight ejection mouth, elongated ejection mouth, etc.
BANDIT 240 DB
BANDIT
Introduction - p. 1
v.206
-

Advertisement

Table of Contents
loading

Summary of Contents for Bandit 240 DB

  • Page 1 BANDIT 240 DB v.206 INTRODUCTION By selecting this device, you have acquired advanced active access-prevention technology. With we offer you an affordable system which guarantees operational reliability, top BANDIT performance and a discrete design. More and more private and public buildings are being equipped with a protection system against burglary.
  • Page 2 : (32) 89 85 85 65 B-3660 Opglabbeek Fax : (32) 89 85 23 64 Belgium web : www.bandit.be Text and drawings in this document are subjected to author protection. Copyright: BANDIT NV, B-3660 Opglabbeek, Belgium. p. 2 - Introduction...
  • Page 3: Safety Precautions

    BANDIT 240 DB v.206 SAFETY PRECAUTIONS Location: - To prevent fire or shock hazard, do not expose this appliance to rain or moisture. - Install the device in such a way to allow a good airflow. - Only install the appliance as described, i.e. In vertical position, with the text on the front panel being readable from the floor.
  • Page 4: Specifications

    BANDIT 240 DB v.206 SPECIFICATIONS Descriptions: - Dimensions: 270 mm wide x 365 mm high x 255 mm deep. 28 kg. - Weight: Fog generator +2 hours and electronics +24 hours. - Max. Mains supply failure: - Reaction time: 1 second between alarm signal and fog ejection.
  • Page 5 BANDIT 240 DB v.206 The unit is packed in a cardboard box: 39 x 39 x 40 cm which contains: 240 DB device. BANDIT - double sided warning sticker “Burglary...” - this installation manual. - "HY-3 grip" tool MOUNTING As a professional, you’ll have to consider properly, what would be the most effective place to install the appliance.
  • Page 6 BANDIT 240 DB v.206 Make sure the is firmly secured to wall or floor, to prevent a burglar with prior BANDIT knowledge from throwing the unit quickly through a window. Use an optional available wallmounting to install the unit against a wall: BANDIT There are two kinds of wallmounting: flat or swivel.
  • Page 7 You’ll save yourself a lot of trouble to keep the device at a working height while connection works are being performed. Mounting more than one BANDIT 240 devices in one large room. Example of mounting in a shop of Example of mounting in a shop of 630 m².
  • Page 8: Electrical Connection

    BANDIT 240 DB v.206 ELECTRICAL CONNECTION 240 DB is equipped with simple and yet versatile wiring schemes. This version is BANDIT adjustable through internal dip switches. The disadvantage of this system is the restriction of possible adjustments, while the big advantage is that it can be installed and adjusted without using PC/laptop or an external adjustment through data or phone connection.
  • Page 9: Pcb Layout

    BANDIT 240 DB v.206 PCB layout 5 way connector remote control Black Orange 6 x Control box Blue PCB connectors Green White Alarm output Alout Guard output Grdout Read OKout Technical output switch Error Blok Tamperloop output [Tampout] Red jump...
  • Page 10 The device, model 240DB , is equipped with 3 inputs. Unlike other Bandit models, where every in- and output is free adjustable, in this 240DB model, the function of each input is fixed through hardware settings in the PCB structure.
  • Page 11 BANDIT 240 DB v.206 Guard input [Grdin] (G+ / G-) Through this input is told the BANDIT alarm system is in ‘guard’ mode. As long as this message is valid, the unit also will be in ‘guard’ mode’. Only if...
  • Page 12 BANDIT 240 DB v.206 Alarm input [Alin] (A+ / A-) Through this input is told the BANDIT alarm system or burglar detector generates a burglar report. If an alarm signal is offered through this input (start pulse) , while the unit is in guard mode,...
  • Page 13 BANDIT 240 DB v.206 Panic input [Panin] (P+ / P-) Through this input can be BANDIT switched directly to “alarm mode” (fog expulsion), bypassing guard mode. Normally this input is used to connect a panic switch. Properties of the panic mode: The red LED "Alarm"...
  • Page 14 BANDIT 240 DB v.206 Outputs The unit has a total of 5 outputs: 1. The 12 volt supply output [Supply] (fixed defined). See further this page. 2. The sabotage loop output [Tmpout] (fixed defined). See page 15. 3. [OKout] is a technical failure output. See page 16.
  • Page 15 BANDIT 240 DB v.206 Output: sabotage loop [Tmpout]: There are two built-in sabotage switches in the appliance (tampers): 1. Through a spring against the rear cover 2. Through a tamper pin, which is built-in in the HY-3 pack , against the side hatch.
  • Page 16 BANDIT 240 DB v.206 Output: failure output [OKout] This is a relay with potential free contacts. They provide a perfect separation between internal electronics and the “outside world”. BANDIT Schematic display of a relay output [Okout]. Electrical properties of a relay output: - potential free - maximum 1 Amp load with 24 V.
  • Page 17 BANDIT 240 DB v.206 Output: guard output [Grdout] This output is a npn-transistor output, so not potential free. This transistor output switches between floating and 0 [Supply]. Electrical properties of a npn-output: Schematic display of the alarm output [Alout] and guard output [Grdout] - not potential free, switches [Supply-] on or off.
  • Page 18 BANDIT 240 DB v.206 Output: alarm output [Alout] This output is a npn-transistor output, so not potential-free. This transistor output switches between floating and 0 [Supply-]. For properties of a npn-transistor output, see previous page 17. This npn-transistor output is represented on the PCB by connectors [Alout].
  • Page 19: Control Box

    BANDIT 240 DB v.206 Control Box BANDIT main PCB The "Control Box" is the most used and requested Control box option which comes with the 240DB. It BANDIT PCB 6 p plug-in permits the installer to easily perform unit tests...
  • Page 20 BANDIT 240 DB v.206 Operation and function: - Bistable switch: BANDIT 240 Control Box With this switch the fog generator is disconnected (so no fog ejection) Same function as “Red Jump” on PCB. With active switch: - The internal electronics continue to...
  • Page 21: Communication Status

    BANDIT 240 DB v.206 COMMUNICATION STATUS The unit gives following visual information to its immediate surroundings: Ejection nozzle FRONT On the -front BANDIT BANDIT you’ll find 6 LEDs. Through these LEDs Failure you can easily see what mode (status) the...
  • Page 22 BANDIT 240 DB v.206 Guard This red LED is on as long as is in guard mode. BANDIT Alarm This red LED is on from the moment switches to alarm mode until the unit is BANDIT put out of guard mode through the guard input [Grdin] or an optional remote control.
  • Page 23: Error Led

    BANDIT 240 DB v.206 Power failure (Power ?) This red LED blinks as long as its power supply or its main fuse F1 is BANDIT detects interrupted and the unit is not in guard mode. is disconnected from the main power supply for more than 3 hours, the BANDIT internal heat exchanger will cool down too much to have a decent performance.
  • Page 24 BANDIT 240 DB v.206 DIP-SWITCH ADJUSTMENTS Through dip-switch adjustments, you can easily program the needed features. Unlike other models, which can be BANDIT programmed in a wide range through PC and/or remotely, the adjustment through dip switches is very simple. This simple method...
  • Page 25 BANDIT 240 DB v.206 - Left button is guard mode on/off Left transmitter Right transmitter and right button is alarm mode button (ch.1) button (ch.2) ‘start’. Put position B1 ‘on’ (1) Guard Guard and B2 ‘on’ (1). The normal Panic...
  • Page 26 BANDIT 240 DB v.206 REPLACEMENT OF HY-3 PACK Mechanically, the inside of consists out of 2 main components: BANDIT -The heat exchanger: this chrome-steel cylinder is filled with hot gasifying channels, which take care of ‘steaming-up’ the injected HY-3 fluid to become a dry fog..
  • Page 27 (green LED switch and front LED “failure” go off). - Repack the “old” HY-3 pack in the original box (tape it). - For refilling: ship the box by normal freight to your BANDIT-dealer. Normally the returned HY-3 packs get a technical check, are refilled, memory reset and tested.
  • Page 28: Maintenance

    BANDIT 240 DB v.206 MAINTENANCE Because is listed as a security device, it is obligatory to regularly perform a function BANDIT check. Every year: Fog expulsion check and failure report check through[OKout]. Using the “Control Box” you can easily perform these tests . The LED bar indicates the quantity of HY-3 fluid present in the HY-3 pack.
  • Page 29 (Material Safety Data Sheet) and/or the approval test of the Belgian Ministry of Health Affairs and/or the German TÜV report. You can always surf to our web site, www.bandit.be, select documents and load the needed files as printable PDF files.
  • Page 30: Examples Of Application

    BANDIT 240 DB v.206 EXAMPLES OF APPLICATION Diagram 1: Alarm system with npn- outputs, technical input and BANDIT- controlled internal siren 12V / max. 250 mA Dip switches: A1:position unit is ON = only in guard if there Read switch is 12V over [Grdin].
  • Page 31 BANDIT 240 DB v.206 Diagram 2: Alarm system with npn-outputs, technical input and additional confirmation sensor. This connection is identical to the previous diagram 1 with the Read switch exception that there is dips Read connected an additional sensor. Only if the...
  • Page 32 BANDIT 240 DB v.206 Diagram 3: Alarm system with relay outputs and external dialer to report a technical failure and alarm. Dip switches: A1:Position unit in ON = guard only if there is 12V over [Grdin]. Read switch So if relevant output...
  • Page 33: Frequently Asked Questions

    (police, fire, etc...) Also look at our sales conditions (www.bandit.be) Keep in mind that the manufacturer is not responsible for goods that are stolen even...
  • Page 34 BANDIT 240DB v.206 Do I have to replace the HY-3 pack (liquid supply) each time the unit has performed a fog expulsion, including false alarms? consumes ~28 ml. of HY-3 fluid each second BANDIT of fog expulsion. A fully charged reservoir contains ~1400 ml.of HY-3 fluid.

Table of Contents