Advertisement
5. OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions before use.
WARNING! DO NOT attempt to overload the lift.
5.1.
Position the lift in a suitable area, checking that the surface on which the lift will stand is solid and flat (preferably concrete).
5.2.
Turn the adjusting stay bolt (30) down to raise the castors (18) off the ground to prevent the lift from moving.
5.3.
Wheel the motorcycle up the leading plate (9) and onto the platform (1).
WARNING! The motorcycle must be fully supported by the lift platform (1) before lifting. DO NOT put the rear wheel of the
motorcycle on the leading plate (9) and DO NOT use the leading plate (9) to support the weight of the motorcycle when lifting.
WARNING! The leading plate (9) is only used to help you to wheel the motorcycle onto the platform when the lift is at its lowest
position.
5.4.
Clamp the front wheel in the vice to prevent any movement of the motorcycle.
NOTE: There is a choice of mounting holes for the vice to cater for various sizes of motorcycle.
5.5.
Strap the motorcycle securely to the platform.
5.6.
Raise the lift by pumping on the foot pedal (22).
5.7.
When the platform has been raised to the working height, pass the locking bar (41) through the holes in the base assembly (16) so that
the lift can not be inadvertently lowered.
5.8.
When the work is done, check under the lift that there are no obstructions and that it is safe to lower the unit. Remove the locking bar (41)
and then SLOWLY press the release foot pedal (21) to GENTLY lower the lift.
NOTE: The speed of lowering is controlled by the release valve. The more the valve is opened the more rapidly the lift descends. Ensure
the descent is slow and controlled.
5.9.
When the lift is fully lowered, unstrap the motocycle, open the vice jaws and remove the motorcycle from the lift.
6. MAINTENANCE
6.1.
When the lift is not in use, it must be stowed in the lowest position to minimise ram and piston corrosion.
6.2.
Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts..
6.3.
Before each use check all parts. If any part of the lift is damaged or would compromise safe use, remove lift from service and take
necessary action to repair.
DO NOT use the lift if it is believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
6.4.
Periodically check the ram and piston for signs of corrosion. Clean exposed areas with a clean oiled cloth.
6.5.
The hydraulic oil level is checked as follows:
1) Remove hydraulic unit from lift and stand upright.
2) Remove vented plug (fig.1.A). Correct oil level is up to plug aperture - add hydraulic oil as necessary.
WARNING! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC OIL, must be used. DO NOT use brake fluid.
IMPORTANT! Only fully qualified personnel should attempt maintenance or repair. Contact your authorised dealer.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE LIFT.
Hydraulic products are repaired by local service agents only. We have service/repair agents in all parts of the UK.
DO NOT RETURN THE PRODUCT TO US. Please call us on 01284 757500 to obtain the address and telephone number of your local agent.
If the product is under guarantee please contact your dealer.
De-commissioning
Should the lift become completely unserviceable, draw off the oil into an approved container and dispose of the lift and the oil according to local
regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
01284 757500
W e b
01284 703534
email
www.sealey.co.uk
sales@sealey.co.uk
MC454
Issue: 1 - 01/10/14
Advertisement
