Ace MUSTANG W640SR User Manual

Table of Contents

Quick Links

User Manual

MUSTANG W640SR NOTEBOOK

Table of Contents

Summary of Contents for Ace MUSTANG W640SR

Page 1 User Manual MUSTANG W640SR NOTEBOOK...
Page 3: Trademarks
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: R&Tte Directive
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. ErP Off Mode Power Consumption Statement: The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode: •...
Page 5: Ce Marking
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation.
Page 6: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 7: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 8: This Computer's Optical Device Is A Laser Class 1 Product
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 9: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 10 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 11: Servicing
Preface Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions: •...
Page 12: Power Safety
Preface Power Safety The computer has specific power requirements:  • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety Warning steady, uninterrupted power supply.
Page 13: Polymer/Lithium-Ion Battery Precautions
Preface Polymer/Lithium-Ion Battery Precautions Note the following information which is specific to Polymer/Lithium-Ion batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer/Lithium-Ion batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
Page 14: General Battery Precautions
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 15: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Cleaning Instructions (For Computer Models Supplied with Light Blue Cleaning Cloth) Some computer models in this series come supplied with a light blue cleaning cloth.
Page 16: Travel Considerations
Preface Travel Considerations As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 17: On The Road
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 18: Developing Good Work Habits
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 19: Lighting
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 20 Preface XVIII...
Page 21: Table Of Contents
Preface Contents Notice ................................I Trademarks ................................... I R&TTE Directive ................................ II ErP Off Mode Power Consumption Statement: ................... II CE Marking ................................III FCC Statement ............................IV FCC RF Radiation Exposure Statement: ..................... V This Computer’s Optical Device is a Laser Class 1 Product ..................VI Instructions for Care and Operation ......................
Page 22 Preface Quick Start Guide Overview ..............................1-1 Advanced Users ............................1-2 Beginners and Not-So-Advanced Users ....................1-2 Warning Boxes ............................1-2 Not Included ..............................1-3 System Startup ............................1-4 System Software ............................1-5 System Map: LCD Panel Open ........................1-6 LED Indicators ............................1-7 Keyboard ..............................1-8 Illuminated LED Keyboard ........................1-9 Keyboard Shortcuts ..........................1-10 Function/Hot Key Indicators ........................1-11 Control Center ............................1-12...
Page 23 Preface Windows 10 Start Menu ..........................1-22 Right-Clicking the Windows Logo In Start Menu ..................1-23 Start Menu Apps & Tiles .........................1-24 Windows 10 Control Panel ........................1-26 Settings ..............................1-27 Windows 10 Taskbar ..........................1-28 Action Center ............................1-29 Video Features ............................1-30 Power Options ............................1-34 Features &...
Page 24 Preface Mouse & Touchpad Devices ........................2-11 Realtek Audio Console ..........................2-18 Realtek Audio Console - Main ........................2-19 Realtek Audio Console - Speakers ......................2-20 Realtek Audio Console - Microphone .....................2-21 Realtek Audio Console - Device Advanced Settings ................2-22 Power Management Overview ..............................3-1 The Power Sources ............................3-2 AC/DC Adapter ............................3-2 Battery ................................3-2...
Page 25 Preface Battery Information ..........................3-16 Battery Power ............................3-16 Power Slider Settings ..........................3-17 Conserving Battery Power ........................3-18 Battery Life ..............................3-19 New Battery .............................3-19 Recharging the Battery with the AC/DC Adapter ...................3-19 Proper handling of the Battery Pack ......................3-20 Battery FAQ .............................3-21 Removing the Battery ..........................3-24 Inserting the Battery ..........................3-25 Drivers &...
Page 26 Preface Video (VGA) .............................4-7 LAN ................................4-7 CardReader ..............................4-7 Touchpad ..............................4-7 Intel® HID Filter Driver ..........................4-7 Control Center ............................4-7 MEI Driver ..............................4-8 Audio .................................4-8 Optional Drivers ............................4-10 BIOS Utilities Overview ..............................5-1 The Insyde BIOS Utility ..........................5-2 UEFI Boot ..............................5-3 Insyde BIOS Start Screen ..........................5-4 Insyde BIOS Start Screen Options: ......................5-5 Boot Manager ............................5-6 Boot From File / File Explorer ........................5-7...
Page 27 Preface Setup Utility - Boot Menu ........................5-20 Setup Utility - Exit Menu ........................5-22 Modules & Options Overview ..............................6-1 Setting Up SATA Mode (Optane™ or AHCI) ..................6-3 AHCI Mode ...............................6-3 Intel® Optane™ ............................6-3 Intel® Rapid Storage Technology Application ..................6-3 Intel® Optane™ Setup Procedure ......................6-4 Wireless LAN Module ..........................6-9 Intel®...
Page 28 Preface Intel SGX Driver Installation ........................6-25 Intel® Speed Shift Technology Driver ....................6-26 Speed Shift Technology Driver Installation ....................6-26 Intel® Rapid Storage Technology ......................6-27 IRST Driver Installation ..........................6-27 Intel® Rapid Storage Technology for Optane Systems ................6-28 Enabling Intel® Optane™ ........................6-29 Disabling Intel® Optane™ ........................6-33 Intel®...
Page 29 Preface Basic Hints and Tips ..........................7-2 Backup and General Maintenance ......................7-3 Viruses ...............................7-4 Upgrading and Adding New Hardware/Software ..................7-5 Problems and Possible Solutions .......................7-7 Interface (Ports & Jacks) Overview ..............................A-1 Notebook Ports and Jacks .........................A-2 Control Center Overview ..............................B-1 Video Driver Controls Video Driver Installation ..........................C-1 Dynamic Video Memory Technology ......................C-1 Configure Other Displays Using Project ....................C-2...
Page 30 Preface Attaching Other Displays ........................C-21 Specifications Core Logic ..............................D-2 Display ..............................D-2 Memory ..............................D-2 Storage ..............................D-2 Audio ................................D-2 Keyboard & Pointing Device ........................D-2 Interface ..............................D-2 Card Reader ..............................D-2 Slot ................................D-3 Communication ............................D-3 Power ................................D-3 Security ..............................D-3 Design Features ............................D-3 Operating System ............................D-3 BIOS .................................D-3 Power Management ..........................D-3 Indicators ..............................D-4...
Page 31 Preface Docking Station Guide Overview ..............................E-1 Compatibility ............................E-1 Computer and Docking Station ........................ E-2 Docked System Power ..........................E-2 System Map: Front View .......................... E-3 System Map: Rear View ........................... E-4 Power Button LED & Lock Switch LED Indicator .................. E-5 System Map: Left &...
Page 32 Preface Power ..............................E-24 Security ..............................E-24 LED Indicators ............................E-24 Environmental Spec ..........................E-24 Dimensions & Weight ..........................E-24...
Page 33: Quick Start Guide Overview
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 34: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1 “BIOS Utilities” on page 5 - 1 in the reminder of the User’s Manual.
Page 35: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows 10) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals.  Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in 1.
Page 36: System Startup
Quick Start Guide System Startup Remove all packing materials, and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. When first setting up the computer use the following procedure (as to safeguard the computer during shipping, the battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below): •...
Page 37: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 10 (64-bit) operating system is supported.
Page 38: System Map: Lcd Panel Open
Quick Start Guide System Map: LCD Panel Open Figure 1 - 2 LCD Panel Open  Built-In PC Camera (Optional) Wireless Device PC Camera LED Operation Aboard Built-In Array Aircraft Microphone The use of any portable electronic transmission Power Button devices aboard aircraft is Keyboard usually prohibited.
Page 39: Led Indicators
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Icon Color Description Orange DC Power is Plugged In White Power Button The Powered USB Port is On* (System Off) White Hard Disk Activity Blinking Orange...
Page 40: Keyboard
Quick Start Guide Keyboard  The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See If your keyboard is Table 1 - 3, on page 1 - 11 for full function key combination details.
Page 41: Illuminated Led Keyboard
Quick Start Guide Illuminated LED Keyboard  (Factory Option) Other Keyboards The optional white illuminated keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operation- If your keyboard is dam- aged or you just want to al features instantly.
Page 42: Keyboard Shortcuts
Quick Start Guide Keyboard Shortcuts  The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navi- gation/operation in Windows 10. Windows Logo Keyboard Shortcut Windows Logo Description Use the Windows logo Key + + D key com- bination to switch be- Tap Winkey Toggle the Start menu tween the Start screen...
Page 43: Function/Hot Key Indicators
Quick Start Guide Function/Hot Key Indicators Keys Function Keys Function Play/Pause (in Audio/Video Programs) Fn + PC Camera Power Toggle Fn + Fn + Fn + TouchPad Toggle Airplane Mode Toggle Turn LCD Backlight Off Fn + Sleep Toggle Fn + (Press a key to or use TouchPad to turn on) Fn + Mute Toggle...
Page 44: Control Center
Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Con- trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/touch pad on/off (see Appendix B...
Page 45: System Map: Front & Docked Views
Quick Start Guide System Map: Front & Docked Views Figure 1 - 6 Front & Docked Views (with Optional Docking Station) LED Indicators Docking Station (Optional)  Docking  If your purchase includes the docking station, open Docking Port Cover the docking port cover latch and align the computer with Make sure you keep the docking cover closed when the computer is not docked in the sta-...
Page 46: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 7 Left View 1. DC-In Jack 2. External Monitor Port 3. RJ-45 LAN Jack 4. 1 * Type-A Powered USB 3.0 Port (USB   3.1 Gen 1) External Monitor Port & RJ-45 5.
Page 47 Quick Start Guide  Thunderbolt Port Devices If your purchase option includes a Thunderbolt port note the following: When plugging a device into a Thunderbolt port allow 30 seconds for the system to scan and recognize the connected device. Ejecting Thunderbolt Devices In order to prevent system problems make sure you do not simply pull the cable out from the Thunderbolt port.
Page 48: System Map: Right & Rear Views
Quick Start Guide System Map: Right & Rear Views Figure 1 - 8 Right & Rear Views 1. 1 * USB 2.0 Port 2. Microphone-In Jack 3. 2-in-1 Audio Jack (Headphone Out/ S/PDIF Out Jack) 4. Optical Device Drive Bay (for DVD Device) ...
Page 49 Quick Start Guide   Changing DVD Regional Codes Disk Eject Warning Go to the Control Panel and double-click Device Man- Don’t try to eject a CD/DVD while the system is ac- ager (Hardware and Sound), then click the + next to cessing it.
Page 50: System Map: Bottom View
Quick Start Guide System Map: Bottom View Figure 1 - 9 Bottom View  Battery Docking Port Fan Intake/Vent The CPU is not a user Component Bay serviceable part. Cover Overheating Speakers To prevent your comput- from overheating make sure nothing blocks the Vent/Fan In- ...
Page 51 Quick Start Guide Battery Removal instructions/3G/4G Module Card Installation Removing the battery is necessary in order to access the USIM card option. If you have included an optional 3G/4G module in your purchase option, follow the instructions below to install the USIM card (provided by your wireless carrier) Turn off the computer, and turn it over and then remove the battery (slide latch in the direction indicated below, then slide hold latch...
Page 52: Inserting The Battery
6 Cell Battery Figure 1 - 11 - Battery Insertion Replacement batteries are available from Ace Computers and can be found at the following website: http://www.acecomputers.com/documents/Mustang_W640SR_Buying_Guide.pdf Your system does not need to be in warranty in order to order spare batteries or other parts.
Page 53: Docking Port
Quick Start Guide Docking Port Follow the instructions below before connecting the computer to the docking station, if included in your pur- chase configuration. Failure to open the cover of the docking port before connecting the computer to the docking station may result in irreparable damage to the connector on the docking station.
Page 54: Windows 10 Start Menu
Quick Start Guide Windows 10 Start Menu Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows Logo Key on the keyboard).
Page 55: Right-Clicking The Windows Logo In Start Menu
Quick Start Guide Right-Clicking the Windows Logo In Start Menu Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an advanced Context Menu of useful features such as Apps and Features, Power Options, Task Manager, Search, File Explorer, Device Manager, Computer Management and Network Connections etc.
Page 56: Start Menu Apps & Tiles
Quick Start Guide Start Menu Apps & Tiles The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of the screen to expand the menu in order to view all the apps (you can use the scroll bar to move up and down the screen).
Page 57 Quick Start Guide Pining/Unpinning Apps & Programs to/from the Start Menu To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the Start Menu right-click the icon and select Unpin from Start.
Page 58: Windows 10 Control Panel
Quick Start Guide Windows 10 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 10. • Select Control Panel under the Windows System item in the Start Menu.
Page 59: Settings
Quick Start Guide Settings The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Apps, Accounts, Time &...
Page 60: Windows 10 Taskbar
Quick Start Guide Windows 10 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the task- bar. The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli- cations referred to throughout the course of this manual can be accessed from here.
Page 61: Action Center
Quick Start Guide Action Center The Action Center appears as a vertical panel on the right side of the screen when you swipe in from the right or click the button in the notification tray. This gives you access to commonly needed functions like Network, All Settings, Airplane Mode, and Project etc.
Page 62: Video Features
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display settings (click the Start Menu and click Settings > System or right-click the desktop and select Display settings) control panel. In Windows 10 it is possible to quickly configure external displays from the Project menu ( press the Windows logo key on your keyboard and the P key or Fn + F7).
Page 63 Quick Start Guide To access the Display Settings: You can quickly adjust the display by right-clicking the desktop and selecting Display Settings. Adjust the settings for Brightness and color, Scale and layout, Resolution and Orientation from the menus. When and external display is attached you can arrange the display configuration from the Multiple Displays menu, and arrange the configuration from Select and rearrange displays.
Page 64 Quick Start Guide To access the Intel(R) HD/UHD Graphics Control Panel: Right-click the desktop and select Intel(R) Graphics Settings from the menu. Click the icon in the notification area of the Desktop taskbar and select Intel(R) Graphics Settings from the menu.
Page 65 Quick Start Guide Minimum Screen Resolution Settings Windows 10 has minimum screen resolution requirements. Right-click a blank area of the Desktop and select Display Settings. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above. Figure 1 - 24 - Display (Resolution) Video Features 1 - 33...
Page 66: Power Options
Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep to the menu - see page 35).
Page 67 Quick Start Guide You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.  Adding Hibernate/Sleep to the Power Men 1.
Page 68 Quick Start Guide 1 - 36...
Page 69: Features & Components Overview
Features & Components Chapter 2: Features & Components  Overview External Optical (CD/DVD) Device Read this chapter to learn more about the following main features and components Drives of the computer: To install applications and drivers etc. you will • Hard Disk Drive/Solid State Drive need to attach an exter- nal optical CD/DVD de- •...
Page 70: Hard Disk Drive/Solid State Drive
Features & Components Hard Disk Drive/Solid State Drive  The hard disk drive (or Solid State Drive) is used to store your data in the computer. Bottom Cover The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk Removal Warning drives with a height of 9.5mm/7mm (see “Storage”...
Page 71: Optical (Cd/Dvd) Device
Features & Components Optical (CD/DVD) Device  There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page D - 2). The Adjustment optical device is usually labeled “Drive D:”...
Page 72: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs  Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.
Page 73: Dvd Regional Codes
Features & Components DVD Regional Codes  To change the DVD regional codes: DVD Region Note Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD region detection is device dependent, not DVD/CD-ROM drives.
Page 74: Multi-In-1 Card Reader
Features & Components Multi-In-1 Card Reader  The card reader allows you to use some of the latest digital storage cards. Push the Push-Push Card card into the slot and it will appear as a removable device, and can be accessed in Reader the same way as your hard disk (s).
Page 75: Smart Card Reader
Features & Components Smart Card Reader  The Smart Card reader reads pocket-sized Smart Cards, chip cards, or integrated cir- Smart Card Driver cuit cards (ICC) with embedded integrated circuits. Smart Cards can be used for se- curity identification, authentication, data storage and application processing within Smart Cards usually re- quire a driver for any large organizations.
Page 76: Touchpad And Buttons/Mouse
Features & Components Touchpad and Buttons/Mouse  The Touchpad is an alternative to the mouse; however, you can also add a mouse to Touchpad Cleaning your computer through one of the USB ports. The Touchpad buttons function in In order to improve pad much the same way as a two-button mouse.
Page 77: Mouse Properties Control Panel
Features & Components Mouse Properties Control Panel You can configure the functions from the Mouse control panel in Windows as fol- lows. Select Control Panel under the Windows System item in the Start Menu (see page 26), or click Additional mouse options from Mouse in Windows Settings (see page 12).
Page 78 Features & Components Figure 2 - 8 Mouse Properties Control Panels 2 - 10 Mouse Properties Control Panel...
Page 79: Mouse & Touchpad Devices
Features & Components Mouse & Touchpad Devices You can configure the functions from the Mouse or Touchpad control panels in De- vices in the Settings control panel as follows. Click the Settings item in the Start Menu (or All Settings in the Action Center). Click Devices.
Page 80 Features & Components Mouse Settings You can select the primary mouse button and scrolling options and access Mouse Properties from Additional mouse options. Figure 2 - 10 Windows Settings Mouse 2 - 12 Mouse & Touchpad Devices...
Page 81 Features & Components Touchpad Settings You can disable the Touchpad by clicking the Touchpad button to turn it off. You can set the system to automatically disable the internal Touchpad when an ex- ternal USB point device (e.g a USB mouse) is attached. Click “Leave touchpad on when a mouse is connected”...
Page 82 Features & Components Touchapd Taps The Touchpad Sensitivity feature helps prevent recognizing taps on the pad by ac- cident, by recognizing when your palm is resting on it or brushing its surface while you are typing. Click in the check box to enable/disable the different gestures or taps on the surface of the pad to perform specific actions to manipulate documents, objects and applica- tions.
Page 83 Features & Components Touchapd Scroll and Zoom Click to enable/disable the two finger scrolling and pinch zooming gesture. Figure 2 - 13 Scroll and Zoom/ Scrolling Gesture The two-finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight con- tinuous motion).
Page 84 Features & Components The three-finger and four-finger swipes and taps can be configured for a number of different functions. Select the appropriate function from the drop-down menu. Figure 2 - 15 Three-Finger Gestures (Swipes & Taps) Figure 2 - 16 Four-Finger Gestures (Swipes &...
Page 85 Features & Components The following is an overview of some of the main gestures you can use with your Touchpad, however these can be configured from the Touchpad menus. Figure 2 - 17 Touchpad Gesture Examples Mouse & Touchpad Devices 2 - 17...
Page 86: Realtek Audio Console
Features & Components Realtek Audio Console  You can configure the audio options on your computer from the Sound control Volume Adjustment panel in Windows, or from the Realtek Audio Console Windows Start menu. The sound volume level Make sure you have installed the driver and checked the Microsoft Store for can be clicking using the updates (see “Audio”...
Page 87 Features & Components Realtek Audio Console - Main  You can adjust the Speaker and Microphone levels by using the sliders in the Re- HD Audio altek Audio Console Main window. HD Audio parameters can be set in the BIOS (see page 10).
Page 88: Realtek Audio Console - Speakers
Features & Components Realtek Audio Console - Speakers Click Speakers to access controls for the format and speaker balance etc. Figure 2 - 20 Realtek Audio Console (Speakers) 2 - 20 Realtek Audio Console...
Page 89: Realtek Audio Console - Microphone
Features & Components Realtek Audio Console - Microphone Click Microphone to access advanced controls for recording on the microphone. Adjust the recording Main Volume level to around 60, to obtain the optimum re- cording quality. Figure 2 - 21 Realtek Audio Console (Microphone) Realtek Audio Console 2 - 21...
Page 90: Realtek Audio Console - Device Advanced Settings
Features & Components Realtek Audio Console - Device Advanced Settings  Device Advanced Settings allows for further configuration of the Connector Set- tings, Playback Device and Recording Device. Device Advanced Settings For the purposes of re- cording it is recommend- that enable “Separate...
Page 91: Power Management Overview
Power Management Chapter 3: Power Management  Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 92: The Power Sources
Power Management The Power Sources  The computer can be powered by either an AC/DC adapter or a battery pack. Forced Off AC/DC Adapter If the system “hangs”, Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ and the Ctrl + Alt + Del DC adapter will damage the computer and its components.
Page 93: Turning On The Computer
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- er button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down).
Page 94: Shutting The Computer Down
Power Management Shutting the Computer Down Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Power item in the Start Menu and select Shut down. If you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power Menu”...
Page 95: Power Plans
Power Management Power Plans  The computer can be configured to conserve power by means of power plans (Con- Resuming trol Panel > Power Options). You can use (or modify) an existing power plan, or Operation create a new one. Table 3 - 1, on The settings may be adjusted to set the display to turn off after a specified time, and for informa-...
Page 96 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Create a power plan to select the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Page 97: Power-Saving States
Power Management Power-Saving States  You can use power-saving states to stop the computer’s operation and restart where Wake On LAN you left off. Windows 10 uses the Sleep, Hibernate and Shut Down power-saving Support states. Wake-On-LAN is only supported from Sleep or Sleep states Hibernate...
Page 98: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost.
Page 99: Configuring The Power Buttons
Power Management Configuring the Power Buttons The power/sleep button (Fn + F12 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. Figure 3 - 5 Power Options Define Power...
Page 100 Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. Go to the Power Options (Hardware and Sound) control panel. Click “Change settings that are currently unavailable” Click Choose what the power buttons do. Click to put a check in the Hibernate/Sleep box under Shutdown settings.
Page 101: Resuming Operation
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F12 key combo). Power Status Icon Color To Resume Table 3 - 1 Power Off Press the Power Button Resuming Press the Power Button...
Page 102 Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Win- dows 10 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Sign out, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu ap- pears to display Sleep, Shut down, and Restart.
Page 103: Settings Menu Power Controls
Power Management Settings Menu Power Controls The Settings item in the Start Menu (or via the Action Center) gives you access to a number of power settings control panels which enable you to quickly adjust power options. Click System to access the menu including the power option settings. Figure 3 - 8 Settings Settings Menu Power Controls 3 - 13...
Page 104 Power Management Battery Saver Battery in Settings will display the battery level, and by clicking Battery usage by app you can see the current state of battery usage by application etc. The Battery saver can be level can be adjusted to be turned on if the battery level falls below a certain level to limit background activity and push notifications.
Page 105 Power Management Power & Sleep Power & sleep gives you quick access to Screen and Sleep settings. Click Addi- tional power settings to go to the main power options control panel. Figure 3 - 10 Settings > Power & Sleep Settings Menu Power Controls 3 - 15...
Page 106: Battery Information
Power Management Battery Information  Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached.
Page 107: Power Slider Settings
Power Management Power Slider Settings  Better Best Battery Saver Battery Saver Better Battery Performance Performance Note that some Win- dows features and back- ground applications may behave differently, or may be blocked, when the system is in Battery Saver mode (check with For DC Only For AC &...
Page 108: Conserving Battery Power
Power Management Conserving Battery Power  • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD The Windows Mobility brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 109: Battery Life
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason (e.g.
Page 110: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack  • DO NOT disassemble the battery pack under any circumstances Caution • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.
Page 111: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 112 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 14 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 113 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 114: Removing The Battery
Power Management Removing the Battery  We recommend that you do not remove the battery yourself. If you do need to re- Bottom Cover move the battery for any reason (e.g. long term storage) see below. Removal Warning Turn the computer off, and turn it over. Do not remove any cov- Slide the latch in the direction of the arrow.
Page 115: Inserting The Battery
Power Management Inserting the Battery Turn the computer off, and turn it over. Slide the battery into the compartment in the direction of the arrow Slide the latches in the direction of the arrows to lock the battery. 9 Cell Battery 6 Cell Battery Figure 3 - 16 Battery Insertion...
Page 116 Power Management 3 - 26...
Page 117: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities  This chapter deals with installing the drivers and utilities essential to the operation or Driver Installation & improvement of some of the computer’s subsystems. The system takes advantage of Power some newer hardware components for which the latest versions of most available op- When installing driv- erating systems haven’t built in drivers and utilities.
Page 118: Driver Installation
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation...
Page 119 Drivers & Utilities Check the driver installation order from (the drivers must be installed in this order) Table 4 - 1, on page 4 - 4 which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them). Follow the instructions for each individual driver installation procedure as listed on the following pages.
Page 120 Drivers & Utilities Win 10 Drivers (64-bit) Page # Win 10 Drivers (64-bit) Other / Options Page # System Required Chipset Page 4 - 7 Setting Up SATA Mode (Optane™ or AHCI) Page 6 - 3 Video (VGA) Page 4 - 7 Wireless LAN Module Page 6 - 9 Page 4 - 7...
Page 121: Updating/Reinstalling Individual Drivers
Drivers & Utilities Manual Driver Installation Updating/Reinstalling Individual Drivers Click Browse CD/DVD (button) in the Drivers Install- If you wish to update/reinstall individual drivers it er application and browse to the executable file in the may be necessary to uninstall the original driver.To do appropriate driver folder.
Page 122: User Account Control
Drivers & Utilities User Account Control  If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Driver Installation General Guidelines Allow, and follow the installation procedure as direct- The driver installation procedure outlined in this Chapter (and in Chapter 7 Options &...
Page 123: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure CardReader Insert the Device Drivers & Utilities + User’s Manual 1. Click 4.Install Cardreader Driver > Yes. disc into your DVD drive and click Install Drivers 2. Click Finish. (button). Touchpad Chipset 1. Click 5.Install Touchpad Driver > Yes. 1.
Page 124: Mei Driver
Drivers & Utilities MEI Driver 9. To prioritize the Realtek audio driver you can click Pause all to pause the download queue. 1. Click 8.Install MEI Driver > Yes. 10. Click on Realtek Audio Control and click on 2. Click Next. 3.
Page 125 Drivers & Utilities  Windows Update After installing all the drivers make sure you enable Win- dows Update in order to get all the latest security up- dates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are con- nected to the internet: Go to the Control Panel.
Page 126: Optional Drivers
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules in- cluded in your purchase option. Figure 4 - 3 - Option Drivers Note that you need to install both the WLAN &...
Page 127: Bios Utilities Overview
BIOS Utilities Chapter 5: BIOS Utilities  Overview BIOS Screens Note that BIOS This chapter gives a brief introduction to the computer’s built-in software BIOS screens pictured (Basic Input/Output System). these pages are intend- ed for guidance in set- ting up your system’s If your computer has never been set up, or you are making important changes to the BIOS.
Page 128: The Insyde Bios Utility
BIOS Utilities The Insyde BIOS Utility  Each time you turn on the computer the system takes a few seconds to conduct a in- BIOS Settings cluding a quick test of the on-board RAM (memory). Warning As the boot process proceeds, the computer will tell you if there is anything wrong. Incorrect settings can cause your system to If there is a problem that prevents the system from booting, it will display a system...
Page 129: Uefi Boot
BIOS Utilities UEFI Boot UEFI (Unified Extensible Firmware Interface) is an advanced firmware standard supporting fast startup. With UEFI Boot prompts at boot to press F2 (to access the BIOS) or F7 (to access Boot options) will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
Page 130: Insyde Bios Start Screen
BIOS Utilities Insyde BIOS Start Screen On accessing the BIOS you will be presented with the Start Screen with 5 menu icons, date and time information, CPU temperature information and navigation and Help icons at the bottom of the screen. You can use the Touchpad, an attached mouse, or the cursor/arrow keys to navigate the menus and press Enter to access the submenu.
Page 131: Insyde Bios Start Screen Options
BIOS Utilities Insyde BIOS Start Screen Options: • Continue: Press Enter here or click Continue to carry on with the boot process and load the operating system. • Boot Manager: Press Enter here or click Boot Manager to access the Boot Manager utility.
Page 132: Boot Manager
BIOS Utilities Boot Manager Figure 5 - 2 Boot Manager  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change When you turn the computer on it will look for an operating system from the devices and revision, therefore your computer’s actual...
Page 133: Boot From File / File Explorer
BIOS Utilities Boot From File / File Explorer Figure 5 - 3 Boot From File (File Explorer) If you need to boot from a file (e.g. on a USB flash drive) then access this menu and use the cursor keys to select the device or file (you can press Enter to explore for a file on an attached device).
Page 134: Administer Secure Boot
BIOS Utilities Administer Secure Boot Figure 5 - 4 Administer Secure Boot Secure Boot prevents unauthorized operating systems and software from loading during the startup process. You can select a trusted UEFI file to execute the BIOS, make sure that you Enforce Secure Boot, Erase all Secure Boot Settings or Restore the Factory Settings.
Page 135 BIOS Utilities You can also make custom changes to the Key Management database if required by accessing the advanced secure boot options for Platform Key (PK Options), Key Ex- change Key (KEK Options), Allowed Signatures Database (DB Options) and For- bidden Signatures Database (DBX Options).
Page 136: Setup Utility - Main Menu
BIOS Utilities Setup Utility - Main Menu Figure 5 - 6 Main (Upper) SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. 5 - 10 Setup Utility - Main Menu...
Page 137 BIOS Utilities OffBoard SATA/NVme Controller Configuration (Main Menu) Pressing Enter opens the sub-menu to show the configuration of any devices on the off board SATA/NVme Controller if applicable. System Time & System Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
Page 138: Setup Utility - Advanced Menu
BIOS Utilities Setup Utility - Advanced Menu Figure 5 - 8 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to enable/disable Intel(R) Speed Shift Technology, VT-d UEFI OS Fast Boot, Intel Software Guard Extensions and to configure the MiniDisplay Port/Thunderbolt port.
Page 139 BIOS Utilities Figure 5 - 9 Advanced Chipset Control Menu Intel(R) Speed Shift Technology (Advanced Menu > Advanced Chipset Control) Use this menu item to enable/disable Intel® Speed Shift Technology. You will also need to install the driver for Intel Speed Shift Technology (see “Intel®...
Page 140 BIOS Utilities VT-d (Advanced Menu > Advanced Chipset Control)  Enable/disable Intel® Virtualization Technology for Directed I/O (VT-d) from this menu. This extends Intel's Virtualization Technology (VT) by providing hard- Thunderbolt Port ware assists for a virtualization solution. Set for Display If you want to use the Thun- UEFI OS Fast Boot(Advanced Menu >...
Page 141 BIOS Utilities SATA Mode (Advanced Menu) The SATA (Serial ATA) control is configured to operate in AHCI Mode (Advanced ® Host Controller Interface) or in RAID Mode (for Intel Optane ™ The SATA Mode should be set BEFORE installing an operating system, and after you have backed up all necessary files and data (see sidebar).
Page 142 BIOS Utilities Intel(R) Thunderbolt Support (Advanced Menu > Thunderbolt Configuration) You can enable/disable discrete Intel(R) Thunderbolt port support from this menu. Security Level (Advanced Menu > Thunderbolt Configuration) You can set the security level to No Security, User Authorization, Secure Connect or Display Port Only.
Page 143: Setup Utility - Security Menu
BIOS Utilities Setup Utility - Security Menu  Security Menu The changes you make here affect the access to the BIOS utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords...
Page 144 BIOS Utilities Note: To clear existing supervisor passwords press Enter and type the existing pass-  word, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. To clear a user password just Password Warning click on Clear User Password.
Page 145 BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press En- ter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to support TPM.
Page 146: Setup Utility - Boot Menu
BIOS Utilities Setup Utility - Boot Menu Figure 5 - 12 Boot Menu & EFI  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change and revision, therefore your computer’s actual...
Page 147 BIOS Utilities UEFI Setting (Boot Menu) The Unified Extensible Firmware Interface (UEFI) specification provides a clean in- terface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services. The Network Stack item can be enabled/disabled as an option under UEFI Setting and PXE Boot capability can be enabled/disabled and configured here.
Page 148: Setup Utility - Exit Menu
BIOS Utilities Setup Utility - Exit Menu Figure 5 - 14 Exit Menu Click Exit Saving Changes (or press F10) to save all changes made and exit the BI- OS. Choosing Exit Discarding Changes will wipe out any changes you have made to the Setup and exit the BIOS.
Page 149: Modules & Options Overview
Modules & Options Chapter 6: Modules & Options  Overview Wireless Device Operation Aboard Aircraft This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please The use of any portable electronic transmission de- contact your service representative.
Page 150 Modules & Options  Important Notice If your purchase option includes both Wireless LAN and 4G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the an- tenna must not be co-located or operate in conjunction with any other antenna or transmitter. Important Notice - 4G &...
Page 151: Setting Up Sata Mode (Optane™ Or Ahci)
Modules & Options Setting Up SATA Mode (Optane™ or AHCI)  AHCI Mode SATA Mode Advanced Host Controller Interface (AHCI) is an interface specification that allows Selection the storage driver to enable advanced serial ATA features such as Native Command The SATA mode selec- Queuing (for maximum hard disk efficiency and performance).
Page 152: Intel® Optane™ Setup Procedure
Modules & Options Intel® Optane™ Setup Procedure  After initial setup make sure you install the Intel Rapid Storage Technology driver - see “IRST Driver Installation” on page 6 - 27). Optane SSD Module Removal ® You need to setup Intel Optane before installing your Windows 10 operating ™...
Page 153 Modules & Options Select SATA Mode (see page 11), press <Enter> and select “RAID Mode.”. Figure 6 - 1 SATA Mode Set to RAID Select “Save and Exit”. As the computer restarts press <F2> to enter the BIOS again. 10. Go to the Advanced menu and you will now see the Intel(R) Rapid Storage Technology (Advanced menu) item.
Page 154 Modules & Options (Note this item only appears after you have restarted and accessed the BIOS again after having set SATA Mode to RAID) Figure 6 - 3 Inte(R) Rapid Storage Technology 6 - 6 Setting Up SATA Mode (Optane™ or AHCI)
Page 155 Modules & Options 11. Select “Save and Exit”, however ensure that the condition in the bulleted point below is met before doing so.  • Make sure the Windows 10 OS DVD is in the DVD drive, as the computer starts Creating a Windows up it will automatically boot from the Windows 10 OS DVD (you will be Partition for Optane...
Page 156 Modules & Options 23. After installing the Intel® Rapid Storage Technology application you can access Device Manager (right-click the Start menu and select Device Manager). 24. Click Disk drives to check the Optane drive. Figure 6 - 4 Device Manager 6 - 8 Setting Up SATA Mode (Optane™...
Page 157: Wireless Lan Module
Modules & Options Wireless LAN Module  If your purchase option includes the Intel® Combination Wireless LAN & Blue- Wireless Device tooth module then install the driver as instructed below. Operation Aboard Aircraft Make sure that the module is on (i.e. the system is not in Airplane Mode) before in- The use of any portable stalling the driver, and that you install the drivers in the order indicated in Table 4 -...
Page 158: Wlan Configuration In Windows
Modules & Options WLAN Configuration in Windows You can configure a wireless connection using one of the following options, how- ever make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Click the Wireless icon in the notification area of the taskbar.
Page 159 Modules & Options Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display Connected status Select any connected network and click Disconnect to disconnect from a connected access point.
Page 160 Modules & Options You can click the Airplane Mode button to turn the mode On or Off. 10. You need to either use Airplane Mode, or turn the WLAN module off aboard aircraft. 11. Network & Internet in Windows Settings will bring up a more comprehensive list of network and internet settings including Wi-Fi (can be turned on/off), Airplane mode (Airplane mode and Wireless devices can be turned on/off) VPN, Dial-up, Ethernet and Proxy.
Page 161: Fingerprint Reader Module
Modules & Options Fingerprint Reader Module  The fingerprint reader module provides a high level of security for your computer. Fingerprint Reader Make sure you have administrator’s rights to your computer, and have a Windows and Power Saving password enabled for full security protection. States There are two different fingerprint modules supplied with this model.
Page 162: Fingerprint Reader Driver Installation
Modules & Options Fingerprint Reader Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers. 3. Click 2.Install Fingerprint Driver > Yes. 4.
Page 163: Fingerprint Module Configuration
Modules & Options Fingerprint Module Configuration  Click the Settings item in the Start Menu and then click Accounts and click Sign- PIN Code in options. You will need to add a Windows password (click Add under Password). You will be asked to add After you have added the password you will need to also add a PIN.
Page 164 Modules & Options You will be instructed to Touch the fingerprint sensor (simply touch the sensor) on the reader a number of times (lift and touch again). Figure 6 - 9 Rest & Lift Your Finger Try to present different parts of your finger in different positions (similar to the various positions you may use when using it, and if you see red at any point try a different position).
Page 165: Bluetooth Combo Module
Modules & Options Bluetooth Combo Module  If your purchase option includes the Intel® Combination Wireless LAN & Blue- Wireless Device tooth module then install the driver as instructed overleaf. Operation Aboard Aircraft Make sure that the module is on (i.e. the system is not in Airplane Mode) before in- The use of any portable stalling the driver, and that you install the drivers in the order indicated in Table 4 -...
Page 166: Intel Bluetooth Combo Driver Installation
Modules & Options Intel Bluetooth Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3.
Page 167 Modules & Options Bluetooth Configuration in Windows Go to the Settings control panel and click Devices (or click the Bluetooth icon in the taskbar and click Add a Bluetooth Device). Click Bluetooth & other devices and make sure Bluetooth is On. Click Add Bluetooth or other device >...
Page 168 Modules & Options Double-click the device you want to pair with the computer and click Connect, if the PIN matches that on the device to which you wish to connect (you may need to click paid on the device). Figure 6 - 12 Bluetooth Connect 6 - 20 Bluetooth Combo Module...
Page 169 Modules & Options Select a device and click Remove Device to disconnect from any device (click Yes to confirm). Figure 6 - 13 Bluetooth Remove Device Bluetooth Combo Module 6 - 21...
Page 170: To Make Your Computer Discoverable To Bluetooth Devices
Modules & Options To Make your Computer Discoverable to Bluetooth Devices Go to the Settings control panel and click Devices (or click the Bluetooth icon in the taskbar and click Open Settings). Click Bluetooth & other devices and click More Bluetooth options. In Bluetooth Settings make sure that Allow Bluetooth devices to find this PC check box (Discovery) has a check inside it.
Page 171: Thunderbolt Port Driver
Modules & Options Thunderbolt Port Driver If you have included the Thunderbolt 3 combo port (factory option) in your pur- chase configuration then you need to install the driver. Before installing the Thunderbolt driver it is necessary to initialize the port first. To do so simply insert any USB Type C device (e.g.
Page 172 Modules & Options  Thunderbolt Port Devices If your purchase option includes a Thunderbolt port note the following: When plugging a device into a Thunderbolt port allow 30 seconds for the system to scan and recognize the connected device. Ejecting Thunderbolt Devices In order to prevent system problems make sure you do not simply pull the cable out from the Thunderbolt port.
Page 173: Intel® Software Guard Extensions
Modules & Options Intel Software Guard Extensions ® Install the Intel® Software Guard Extensions Driver which provides a set of in- structions allowing user-level code a degree of security, and privacy, from the oper- ating system. Intel SGX Driver Installation Make sure you have enabled Software Guard Extensions from Advanced Chipset Control in the Advanced Menu in the BIOS before installing the driver (see “SW...
Page 174: Intel® Speed Shift Technology Driver
Modules & Options Intel Speed Shift Technology Driver ®  Install the Intel® Speed Shift Technology driver as outlined below. Speed Shift *P-States Technology allows operating system to hand off some or all control of the handing P-states are voltage-fre- of the computer’s *P-States to the processor.
Page 175: Intel® Rapid Storage Technology
Modules & Options Intel Rapid Storage Technology ®  Install the Intel® Rapid Storage Technology to support your AHCI mode SATA IRST and M.2 PCI-e drive (see “SATA Mode (Advanced Menu)” on page 5 - 15). SSDs Note that Intel® Rapid Storage Technology IRST Driver Installation...
Page 176: Intel® Rapid Storage Technology For Optane Systems
Modules & Options Intel® Rapid Storage Technology for Optane Systems  Intel® Rapid Storage Technology application displays status information on your Intel® Optane™ configuration. Run the Intel® Rapid Storage Technology appli- Optane SSD Module Removal cation from the item in the Start menu. If you need to remove an When the Intel®...
Page 177: Enabling Intel® Optane
Modules & Options Enabling Intel® Optane™ Run the Intel® Rapid Storage Technology application. Click Enable. Figure 6 - 16 ® IRST - Intel ™ Optane Memory (Enable) Enable The system will pop-up a message and ask you to select a compatible fast drive (in this case there should only be one option).
Page 178 Modules & Options You will need to restart the computer after enabling Optane, and make sure the system is powered by the powered AC/DC adapter, and not by battery only. Click Yes to begin the process (this may take some time). You can click the Intel Optane Memory tab in the IRST control panel and click Reboot to restart the computer, or simply after the process has been completed restart the computer.
Page 179 Modules & Options After restarting can access Device Manager (right-click the Start menu and select Device Manager). Click Disk drives to check that the drive should read Intel Optane ******. Figure 6 - 19 Device Manager (Disk drives) Intel® Rapid Storage Technology 6 - 31...
Page 180 Modules & Options Run the Intel® Rapid Storage Technology application to check the status. Figure 6 - 20 ® IRST - Intel ™ Optane Memory (Enabled) 6 - 32 Intel® Rapid Storage Technology...
Page 181: Disabling Intel® Optane
Modules & Options Disabling Intel® Optane™  If you need to disable Intel® Optane™ for any reason follow these instructions. Disabling Intel® Run the Intel® Rapid Storage Technology application. Optane™ Click Disable. Disable Intel® Optane™ if you want to reinstall/ reset the system, re- move the Optane SSD or update the IRST driv-...
Page 182 Modules & Options Restart the computer to complete the process. Run the Intel® Rapid Storage Technology application.  The Status of Intel® Optane™ Memory is indicated in the Window. HDDs & Intel® To enable Intel® Optane™ Memory follow the process indicated in “Enabling Optane™...
Page 183 Modules & Options Restart your notebook computer and press <F2> to enter the BIOS. Go to the Advanced menu and you will now see the Intel(R) Rapid Storage Technology (Advanced menu) item. You can and press <Enter> to check the information.
Page 184 Modules & Options 11. Click Disable. Figure 6 - 25 Intel(R) Rapid Storage Technology (Disable Optane) 12. You can click to either Enable or Disable “Preserve user data:” 13. Click on “Are you sure you want to disable?” and select Yes. Figure 6 - 26 Intel(R) Rapid Storage Technology...
Page 185: Intel® Vpro™ Technology
Modules & Options Intel® vPro™ Technology  Intel® vPro™ Technology is supported by Model A computers only. This set of Wake On LAN From technology features, built into the computer’s motherboard, allows Information G3 Power-Saving Technology departments remote access to the computer. This allows the IT depart- States ment to monitor, maintain and manage computers regardless of the state of the op- Only Model A computers,...
Page 186 Modules & Options Figure 6 - 27 Intel(R) Management Engine (Password Creation) Select MEBx Login and press “Enter” to access the password screen. Enter the pass- word “admin” (without quotes) and you wild then be prompted to enter your own password (note the password information on the previous page).
Page 187 Modules & Options Figure 6 - 28 Intel® Management and Security Status  Help Click Learn More to and then click For more infor- mation refer to the user guide. Intel® vPro™ Technology 6 - 39...
Page 188: Pc Camera Module
Modules & Options PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated (see Figure 1 - 2 on page 1 - 6). Note that you need to use the Camera app in Windows to take pictures and capture video.
Page 189: Camera App
Modules & Options Camera App Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera app from the Start menu by clicking on the Camera app icon (you can type “camera”...
Page 190 Modules & Options Click Settings to access the camera settings menu to make adjustments for Camera press and hold button, photo Aspect ratio, Framing grid, Time lapse, video recording frame rates and Flicker reduction.  Camera Settings The Self Timer can be set to take Photos after 2, 5 or 10 seconds and can also be set to continue taking pictures until the camera button is pressed again (Photo Burst).
Page 191 Modules & Options With the Pro menu expanded you can access the Exposure compensation button to adjust the brightness. Figure 6 - 32 Camera Brightness Adjustment PC Camera Module 6 - 43...
Page 192: Taking Pictures/Capturing Video
Modules & Options Taking Pictures/Capturing Video Make sure the PC Camera is turned on by using the Fn + F10 key combination (or Control Center button). Run the Camera app from the Start menu by clicking on the Camera app icon (you can type “camera”...
Page 193 Modules & Options Captured photos and videos will be saved to the Photos app stored in the Start menu (type Photos into the search box if you cannot find the app). You can also access the photos from the Camera roll icon at the bottom right of the Camera app screen.
Page 194: Trusted Platform Module
Modules & Options Trusted Platform Module (Optional) The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a sys- tem administrator before users can access security features.
Page 195: Enabling & Activating Tpm
Modules & Options Enabling & Activating TPM  Restart the computer. Enter the BIOS pressing F2 during the POST/startup. Clearing TPM Click to enter the Setup Utility and select the Security menu. Information Click TPM Configuration and select Enable for Security Device Support. You will then need to save the changes and restart the computer.
Page 196: Tpm Management In Windows
Modules & Options TPM Management in Windows You can manage your TPM settings from within Windows: Go to the Control Panel. Click BitLocker Drive Encryption (System and Security). Click TPM Administration. Figure 6 - 36 BitLocker Drive Encryption (TPM Administration) 6 - 48 Trusted Platform Module...
Page 197 Modules & Options The TPM Management window allows you to configure the TPM within Windows. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Figure 6 - 37 Trusted Platform Module (TPM) Management on...
Page 198: Tpm Actions
Modules & Options TPM Actions Click Prepare the TPM and follow the instructions in the Wizard to prepare the TPM (this will probably require a restart of the computer and confirmation of the setting changes after restart by pressing the appropriate F key). After the restart the TPM will be prepared and you can then use the Actions menu to Turn TPM off, Change Owner Password, Clear TPM or Reset TPM Lockout.
Page 199 Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk. Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security). Click Turn on Bit Locker. Follow the on-screen instructions to setup BitLocker, and make sure you have a removable media (e.g.
Page 200: 3G/4G Module
Modules & Options 3G/4G Module  If you have included an optional UMTS/HSPDA+ based 3G module (Universal Wireless Device Mobile Telecommunications System or High Speed Packet Access) module or LTE Operation Aboard Aircraft (Long Term Evolution) 4G module (see “Communication” on page D - 3 for spec- The use of any portable ification details) in your purchase option, you do not require a driver/application...
Page 201 Modules & Options 3G/4G Module USIM Card Installation  Follow the instructions below to install the USIM card (which will be supplied by Power Safety your service provider). Warning Turn off the computer, and turn it over and then remove the battery (slide latch Before you undertake any in the direction indicated below, then slide hold latch in place and slide the bat-...
Page 202 Modules & Options Inserting the Battery  Turn the computer off, and turn it over. Slide the battery into the compartment in the direction of the arrow USIM Card Ejection Slide the latches in the direction of the arrows to lock the battery Simply press on the USIM card to eject it, however do 9 Cell Battery...
Page 203: 4G Configuration
Modules & Options 4G Configuration You can configure a 4G connection as below, however make sure the system is not in Airplane Mode before configuration begins and turn Wi-Fi Off in order to use your 4G connection as priority. You can connect to a 4G connection in much the same way as the WLAN connection except you use the Cellular menu.
Page 204 Modules & Options Click Connect to connect to the cellular network manually. Once connected you can then access the internet, download e-mail etc. as per any  internet connection. Power Saving States & Click Disconnect to drop the connection to the cellular network. Cellular Connections You will need to turn your Wi-Fi on again after disconnecting.
Page 205 Modules & Options Cellular in Network & Internet in Windows Settings will allow you to access some further cellular settings. Figure 6 - 45 Network & Internet Settings > Cellular 3G/4G Module 6 - 57...
Page 206 Modules & Options Click Advanced options to access more detailed menu options. Figure 6 - 46 Cellular > Advanced Options 6 - 58 3G/4G Module...
Page 207: Troubleshooting Overview
Troubleshooting Chapter 7: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 208: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 209: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 210: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 211: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 212 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 213: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
Page 214 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see 18).
Page 215 Troubleshooting Problem Possible Cause - Solution No image appears on the external You haven’t installed the video driver and configured it appropriately from the monitor I have plugged in and powered Control Panel. See for instructions on installing and configuring Appendix C the video driver.
Page 216 Troubleshooting Problem Possible Cause - Solution appear when is lit, then Num Lock is turned ON. (see Unwelcome numbers If the LED “LED Indicators” on typing. page 1 -  Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
Page 217 Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be The module is off. Press the Fn + F10 key combination in order to enable the detected. module (see 11). Run the camera “Function/Hot Key Indicators” on page 1 - application to view the camera picture.
Page 218 Troubleshooting Problem Possible Cause - Solution The computer is off (or in Sleep Mode) but The port is not powered on. Toggle power to the port using the Fn + power powered by the AC/DC adapter plugged in button combination. to a working outlet, or by battery with a This function may not work with certain external USB compliant devices (check capacity above 20%.
Page 219: Interface (Ports & Jacks) Overview
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 220: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description 2-in-1 Audio Jack This is a combination headphone/S/PDIF Jack. Headphones or speakers can be connected (Headphone-Out Jack/SPDIF through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack.
Page 221 Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini DisplayPort 1.2 Mini DisplayPorts are miniaturized versions of the DisplayPort, which is a digital display interface standard that allows a digital audio/video interconnect, between the computer and its external display or a home-theater system.
Page 222 Interface (Ports & Jacks) Item Description USB 2.0 Ports These USB ports are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or Powered USB 3.0 (USB 3.1 above, make sure you use the power supply which comes with the device).
Page 223 Interface (Ports & Jacks) Item Description Thunderbolt 3 Combo Port This Thunderbolt 3 port allows for the connection of external peripherals to the computer by ™ (Shared with the USB Type-C combining PCI Express (PCIe), DisplayPort (DP), USB 3.1 and its own Thunderbolt 3 Port) technologies.
Page 224 Interface (Ports & Jacks) A - 6...
Page 225: Control Center Overview
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls and settings. Click the Control Center icons to toggle the appro- priate function, or hold the mouse button down and move the dial control where applicable.
Page 226 Control Center Control Center Menus The Control Center contains 2 menu headings (Basic Setting & Extra Setting). The Extra Setting tab al- lows you to adjust the app skin color to your choice. A third menu item (LED Device) is available for systems supporting illuminated white LED keyboards only.
Page 227 Control Center Power Modes You can set a Power Mode by clicking the appropriate icon in the center of the Control Center. Each pow- er mode will affect Airplane Mode and PC camera power. Figure B - 3 - Power Modes •...
Page 228 Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level.
Page 229 Control Center Sleep / Hibernate Button Click either the Hibernate or Sleep buttons to have the computer enter the selected power-saving mode (you will receive a warning before the system switches to the power-saving mode and will need to click OK to con- firm).
Page 230 Control Center LED Device Menu - KB Sleep Timer / KB Brightness Enable and then select the amount of time the system for which the system is idle before the keyboard LED en- ters sleep mode (i.e. the LED keyboard illumination will turn off to save power). You can also adjust the key- board brightness.
Page 231: Video Driver Controls
Video Driver Controls Appendix C: Video Driver Controls  The basic settings for configuring the LCD are outlined in “Video Features” on Video Card Options page 1 - Note that card types, specifications and driv- Video Driver Installation ers are subject to contin- updates Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 -...
Page 232: Configure Other Displays Using Project
Video Driver Controls Configure Other Displays Using Project You can configure attached displays from Project. Attach your display to the appropriate port, and turn it on. Press the + P key combination. Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen only.
Page 233: Configuring An External Display In Windows
Video Driver Controls Configuring an External Display In Windows The System > Display Control Panel in Settings may also be used to configure dis- plays. Attach your external display to the appropriate port, and turn it on. Click the Start Menu and click Settings > System (or right-click the desktop and select Display Settings).
Page 234: Hdmi Audio Configuration
Video Driver Controls HDMI Audio Configuration  HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Volume Adjustment In some cases it will be necessary to go to the Sound control panel and manually The sound volume level configure the HDMI audio output as per the instructions below. can be clicking using the Go to the Sound control panel.
Page 235 Video Driver Controls Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel. Figure C - 4 HDMI Device Properties HDMI Audio Configuration C - 5...
Page 236 Video Driver Controls HDMI Notes  • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • To play audio sources through your external display’s (TV or LCD) speakers If you are using a third you will need to go to the audio configuration control panel on the display and party application to play...
Page 237: Wireless Display Configuration
Video Driver Controls Wireless Display Configuration Note that no driver or application is required for wireless display in Windows 10. Press the + P key combination. Click Connect to a wireless display at the bottom of the Project screen and follow the steps to connect to any wireless enabled display.
Page 238 Video Driver Controls You may then need to input a pin number for the device to which you are connecting and click Next. The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details). Go to the Project menu and click Disconnect to temporarily disconnect from the wireless display.
Page 239: Intel® Hd/Uhd Graphics Control Panel
Video Driver Controls Intel HD/UHD Graphics Control Panel ® Advanced video configuration options are provided by the Intel HD/UHD Con- ® trol Panel. To access the control panel see below and overleaf: Right-click the Desktop and select Intel(R) Graphics Settings from the menu. Figure C - 6 Right-Click Desktop (Intel Graphics...
Page 240 Video Driver Controls Double-click the Intel(R) HD/UHD Graphics control panel in the Windows Control Panel. Figure C - 8 Control Panel Intel Graphics ® Settings C - 10 Intel® HD/UHD Graphics Control Panel...
Page 241 Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate  menu panel and adjusting the settings from the menus. Home Click the Home button to return to the main menu screen in any of the sub- menu screens.
Page 242 Video Driver Controls Display  Click either General Settings or Color Settings to make display adjustments, in- cluding configuration for any attached external displays. Multiple Display At least one other dis- play must be attached in order to view multiple display selection tions.
Page 243 Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Mul-  tiple Displays menu allows you to configure the display mode of any attached dis- plays (see “Attaching Other Displays” on page C - 21).
Page 244 Video Driver Controls The Custom Resolutions sub-menu allows you to adjust the display (or any at- tached display) to any width, height, refresh rate, color depth and underscan percent- age of your choice. Note that incorrect settings can cause system instability and even possible component damage, so this is adjusted at your own risk.
Page 245 Video Driver Controls This menu allows you to choose how 3D images are displayed. Performance gives the smoothest motion of images, Quality displays the most detail, Balanced Mode provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering and Vertical Sync and features to your prefer- ences.
Page 246 Video Driver Controls Options and Support Hot Key Manager in Options and Support allows you to create hot keys for open- ing the application and scaling etc. Click Apply to save changes. Figure C - 14 Intel ® HD/UHD Graphics Control Panel Options and Support...
Page 247 Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The In-  formation Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel®...
Page 248 Video Driver Controls Video The Video menu allows you to brighten or darken movies, or to switch to vivid col- ors. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes (select Color Enhancement or Image Enhancement from the menu).
Page 249 Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhance- ment, Noise Reduction, Contrast Enhancement and Film Mode Detection. Click Apply to save changes. Figure C - 17 Intel ®...
Page 250: Display Devices & Options
Video Driver Controls Display Devices & Options  Note that you can use external displays connected to the HDMI-Out port and/or ex- 4K2K Videos on 4K2K ternal monitor port and Mini Display (1.2) port (or Thunderbolt port if applicable). External Displays See your display device manual to see which formats are supported.
Page 251: Attaching Other Displays
Video Driver Controls Attaching Other Displays  To Clone Displays: Multiple Display Attach your external display to the appropriate port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > At least one other dis- Multiple Displays (sub-menu).
Page 252 Video Driver Controls To Enable Extended Mode:  Attach your external display to the appropriate port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Display Settings Multiple Displays (sub-menu). Extended Desktop Click Extended from the Select Display Mode menu.
Page 253 Video Driver Controls To Enable Collage Mode: Attach your external display to the appropriate port, and turn it on.  Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Collage Mode Multiple Displays (sub-menu). Click Collage from the Select Multiple Display Mode menu. Collage mode is used to Click Enable Collage and click On.
Page 254 Video Driver Controls C - 24...
Page 255: Specifications
Specifications Appendix D: Specifications  Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Page 256: Core Logic
Specifications Core Logic Storage Interface Intel® H370 Chipset One Changeable 2.5" / 7.0 mm (h) HDD/ One USB 2.0 Port SSD with SATA (Serial) Interface Two USB 3.0 (USB 3.1 Gen 1) Port (Type-A) - (Including 1 ACDC Powered USB Port) One Changeable 9.0 / 9.5 mm(h) DVD Display One USB 3.1 (USB 3.1 Gen 1) Port (Type-C)
Page 257: Slot
4G Module with USB Interface (B Key) Drivers and BIOS Updates may be obtained Security from Ace Computers via download - See Communication Drivers Link at www.acecomputers.com/ Security (Kensington® Type) Lock Slot driverdownload.asp...
Page 258: Indicators
Specifications Indicators Power/Suspend, Battery, HDD/ODD, Airplane Mode, Num Lock, Caps Lock, Scroll Lock, Camera (on module) Environmental Spec Temperature ° ° Operating: C - 35 Non-Operating: 20% - 80% Relative Humidity ° ° Operating: C - 60 Non-Operating: 10% - 90% Dimensions &...
Page 259: Docking Station Guide Overview
Docking Station Guide Appendix E: Docking Station Guide Overview The docking station provides your computer with an easy connectable desktop environment when portability is not required. This allows for easy connections to external displays, USB devices (with a full range of extra USB ports), audio devices and provides a battery charging facility.
Page 260: Computer And Docking Station
Docking Station Guide Computer and Docking Station The computer may hot or cold dock/undock with the docking station, i.e. the computer may be powered on (hot docking/undocking) or powered off (cold docking/undocking) when docking or undocking. However if you in- tend to hot dock/undock the system then make sure that the hot key driver, provided on the computer’s Device Drivers &...
Page 261: System Map: Front View
Docking Station Guide System Map: Front View Figure E - 1 System Map Front Power Button LED Backup Hotkey (if a Hard Disk is installed in the Device Bay) Lock Switch Notebook Eject Latch Notebook Placeholder Retaining Pins Docking Connector Eject Pins ...
Page 262: System Map: Rear View
Docking Station Guide System Map: Rear View Figure E - 2 System Map Rear Security Lock Slot USB 3.0 Port DVI-D Out Port HDMI-Out Port External Monitor Port RS232 (Serial) COM Port RJ-45 LAN Jack DC-In Jack Headphone Jack 10. Microphone Jack 11.
Page 263: Power Button Led & Lock Switch Led Indicator
Docking Station Guide Power Button LED & Lock Switch LED Indicator Icon Color Description Orange DC Power is Plugged In and the Computer is Off or in Hibernate Mode* Green The Docking Station is On or in Sleep Mode Table E - 1 - Power Button LED & Lock Switch LED Indicator *To confirm the computer’s power status check the LED Power Indicators on the computer itself.
Page 264: System Map: Left & Right Views
Docking Station Guide System Map: Left & Right Views Figure E - 3 System Map Left & Right Views Bay with HDD or Dummy Caddy Powered USB 3.0 Port USB 3.0 Ports  USB Port Power Note that power to the notebook computer and docking station’s USB ports may be enabled/ disabled in the notebook computer’s BIOS settings (see the BIOS guide in Chapter 5 of the notebook’s user manual).
Page 265: Cold Docking The Computer To The Docking Station
Docking Station Guide Cold Docking the Computer to the Docking Station Remove all packing materials and place the docking station on a stable surface. Securely attach any peripherals you want to use with the docking station (e.g. keyboard and mouse) to their ports.
Page 266 Docking Station Guide Make sure the computer’s hot key driver is installed (especially if you intend to hot dock the system). Remove the AC/DC adapter from the notebook computer and then close the computer’s lid/LCD and turn it over (if you are using the optional 9 cell battery make sure you remove the battery before attempting to dock the computer with the docking station).
Page 267 Docking Station Guide Make sure that the notebook computer’s AC/DC adapter is NOT ATTACHED to the computer’s DC-In jack and that the computer is OFF. Ensure that the lock switch on the docking station is in the unlock position. 10. Press the computer down onto the docking station so that the docking connectors line up. 11.
Page 268: Cold Undocking The Computer From The Docking Station
Docking Station Guide Cold Undocking the Computer from the Docking Station Shut the computer down as per the normal Windows shutdown (select Shut Down from the Start menu in Win- dows) procedure (the Power LED on the docking station will be orange). Slide the lock switch on the docking station in to the unlock position.
Page 269: Hot Docking The Computer To The Docking Station
Docking Station Guide Hot Docking the Computer to the Docking Station Remove all packing materials and place the docking station on a stable surface. Securely attach any peripherals you want to use with the docking station (e.g. keyboard and mouse) to their ports.
Page 270 Docking Station Guide Make sure the computer’s Control Panel AP driver is installed for hot docking/undocking the system. The computer should be on, however remove the AC/DC adapter from the notebook computer and then close the computer’s lid/LCD and turn it over (if you are using the optional 9 cell battery you cannot hot dock the computer with the docking station).
Page 271 Docking Station Guide Ensure that the lock switch on the docking station is in the unlock position. Press the computer down onto the docking station so that the docking connectors line up (the Power LED on the docking station will be orange). 10.
Page 272: Hot Undocking The Computer From The Docking Station
Docking Station Guide Hot Undocking the Computer from the Docking Station Hot undocking using Windows: When the system is docked click the icon in the taskbar notification area and click Safely Remove Hard- (Figure E - 11) from the menu. ware and Eject Media Select Eject Docking Station and the Undock Complete...
Page 273: Power Button Configuration
Docking Station Guide Power Button Configuration To prevent your computer from entering a power-saving state if you choose to work with the lid/LCD closed, then it may be necessary to redefine what the computer is set to do if the lid/LCD is closed when plugged in. Go to the click Power Options (Hardware and Sound) control panel.
Page 274: Docking Station Ports & Jacks
Docking Station Guide Docking Station Ports & Jacks The following will give a quick description of the interface (ports & jacks) which allow your docking station and computer to communicate with external devices, connect to the internet etc. When the notebook is docked to the docking station all the ports on the docking station will function, however only some of the ports on the notebook will function (see the note alongside each item for specific information.
Page 275 Docking Station Guide Item Description Note External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel only external Port Display, to get dual video or simultaneous display on the LCD and monitor port on the docking external monitor/FPD.
Page 276 Docking Station Guide Item Description Note Headphone-Out Jack Headphones or speakers may be connected through this jack. You can use the headphone Note: Set your system’s volume to a reduced level before and microphone jacks on connecting to this jack. either the computer and/or docking station when the Microphone-In Jack...
Page 277 Docking Station Guide Item Description Note Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1”...
Page 278 Docking Station Guide Item Description Note USB 2.0/1.1 Ports* These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 You can use the ports on compliant) are for low-speed peripherals such as keyboards, mice both the computer and the or scanners, and for high-speed peripherals such as external docking station when the HDDs, digital video cameras or high-speed scanners etc.
Page 279: Multiple Displays
Docking Station Guide Multiple Displays Any two of the following displays may be enabled simultaneously when the system is docked. You can toggle through the display options by using the Fn + F7 key combination (make sure any attached displays are powered on).
Page 280 Docking Station Guide Backup Hotkey When the system is docked you can press the Backup Hotkey ( Figure E - 13) to launch the Windows Re- covery (see overleaf) application. If you do not have a hard disk installed in the docking station you can set the Windows File History application to backup to any attached hard disk, CD/DVD or non system partition of your computer.
Page 281 Docking Station Guide Press the hard disk backup hotkey. This will run the Windows Recovery control panel. You can then choose to backup individual files and folders or alternatively create a System Image Backup (see your Windows documentation for details). Figure E - 14 - Windows Recovery Backup Hotkey E - 23...
Page 282: Specifications
Docking Station Guide Specifications Power Full Range AC/DC 90W Adapter Storage AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 4.74A One Changeable 2.5" / 9.5 mm(H) HDD Caddy with SATA (Serial) Interface (Factory Option) Security Security (Kensington® Type) Lock Slot Interface and Ports Three USB 2.0 Ports LED Indicators...

Ace MUSTANG W640SR User Manual

Quick Start Guide Overview

Features & Components Overview

Power Management Overview

Drivers & Utilities

BIOS Utilities Overview

Modules & Options Overview

3 G/4G Module

4 G Configuration

Troubleshooting Overview

Interface (Ports & Jacks) Overview

Control Center Overview

Video Driver Controls

Specifications

Docking Station Guide Overview

Quick Links

Related Manuals for Ace MUSTANG W640SR

Summary of Contents for Ace MUSTANG W640SR