Summary of Contents for Pentashot Hit&Miss Connect
- Page 1 Target Hit&Miss Connect DESCRIPTION AND OPERATING MANUAL Pentashot EU s.r.o. 2019...
-
Page 2: Table Of Contents
Complete solution CONTENTS 1/ Safety notes and important information ............. 3 2/ Description, using the program ................4 3/ How the target application works................7 4/ Main menu ........................8 5/ Modes ...........................9 6/ Power supply ......................10... -
Page 3: 1/ Safety Notes And Important Information
• The target should be positioned such that the sun’s rays do not directly reach its front surface (UIPM rule B.5.15.i). • Only PENTASHOT external lights can be used with this target. • The laser target is opto-electric equipment and dismantling it is forbidden! •... -
Page 4: 2/ Description, Using The Program
LED lights up. A shot to the miss zone is signalled when a red LED lights up. The Hit&Miss Connect target is mainly intended for use with the PENTASHOT application, which is for displaying results and setting the target. The application contains three main setting modes, which are described later in the manual. - Page 5 Complete solution You can start shooting at the target. The target automatically shuts off 20 minutes after the last shot. The target can also be turned off by pressing the START button for about 5 seconds. An audible signal shows it has been turned off. BATTERY COMPARTMENT CONNECTING EXTERNAL LIGHTS The target can be connected only to NAVISTREET external lights through a UTP cable and connector.
- Page 6 UPDATE FUNCTION The target can be updated only by the manufacturer or an authorized person. A computer with the update or service software can be plugged to the connector. PLACING THE TARGET The target must never be placed where sunlight directly reaches the target surface, because this will disturb its operation.
-
Page 7: 3/ How The Target Application Works
Complete solution 3/ HOW THE TARGET APPLICATION WORKS After the target is turned on, the Bluetooth function automatically activates. After switching on, the application shows the first screen, the target number. For checking, the target number can be found on the back. It is the same as the serial number. After connection, a window with the main menu appears. -
Page 8: 4/ Main Menu
Complete solution 4/ MAIN MENU TRAINING – after clicking the link to this mode. COMPETITION – after clicking the link to this mode. INDIVIDUAL – after clicking the link to this mode. SETTINGS – from here you can set the LED intensity and shut off the target. RESULTS –... -
Page 9: 5/ Modes
Complete solution 5/ MODES TRAINING - Allows shooting without limiting the time or number of shots. The LEDs show HIT or MISS. Green means HIT, and red means MISS. In this mode, the results are not stored, and they can’t be adjusted in any way. COMPETITION –... -
Page 10: 6/ Power Supply
Complete solution INDIVIDUAL – Shooting time can be set between 10 and 60 seconds. You can also set the number of possible shots (MISS and HIT) from 5 to infinity. You can also set the number of rounds from 1 to 4 and make the HIT ZONE smaller when the HIT ZONE is from circle 8. - Page 11 Complete solution www.pentashot.eu Addresses: PENTASHOT EU s.r.o. Zámecká 2315/9 70200 Ostrava E-mail: jiri@pentashot.eu business@pentashot.eu info@pentashot.eu Delivery address: PENTASHOT EU s.r.o. Kosmova 1090/11 70200 Ostrava Telephone: +420 605 252 433 +420 773 002 110 +420 607 056 112...
- Page 12 Complete solution TECHNICAL PARAMETERS Parameter Value Dimensions 270 mm x 190 mm x 32 mm Size of HIT zone ø 59.9 mm Size of MISS zone 180 mm x 175 mm Weight 684 g with batteries Shooting time 50 seconds (one round) Two 1.5V AA batteries (alkaline Power source recommended) USB cable from the electrical grid...