Related Manuals for Idis DC-TH Series
Summary of Contents for Idis DC-TH Series
- Page 1 DC-TH201x Installation Guide Thermal Cameras DC-TH Series DC-TH2011 DC-TH2011W / TH2012W DC-TH2011WR / TH2012WR...
-
Page 3: Table Of Contents
Notes on Installation Required Settings of Camera How to Register to NVR or VMS 1.3.1 Connect with NVR 1.3.2 Connect with VMS on PC (IDIS Center & ISS Client) Installation Method Alarm Function The Camera Alert Function 2.1.1 Alert on thermal image 2.1.2... -
Page 4: Installation Method
1. Installation Method 1.1 Notes on Installation - This camera is designed for indoor use only and should be installed where constant temperature can be maintained. Outdoor usage is strongly not recommended. ㆍDo not point the camera towards the entrance or the outside of the building. ㆍDeploy the solution indoors only in an environment with a constant temperature and no wind. -
Page 5: How To Register To Nvr Or Vms
- Setting threshold temperature The threshold temperature can be set in SET Temperature’.UP - Video - Live Screen Setup. Tick ‘ON’ of the ‘Event Report’ and setup ‘Event Max 1.3 How to Register to NVR or VMS 1.3.1 Connect with NVR DC-TH201x can be used by connecting with NVR. -
Page 6: Connect With Vms On Pc (Idis Center & Iss Client)
※The streaming resolution has to be changed in NVR side. Refer to 3. Notes on Use. 1.3.2 Connect with VMS on PC (IDIS Center & ISS Client) DC-TH201x can be used by connecting with VMS. In this case, there are two ways to connect to VMS. -
Page 7: Installation Method
1.4 Installation Method It is highly and particularly recommended that the camera only be used for detecting fixed subjects to guarantee accurate temperature. Please install and apply the camera as instructed below. 1) Place the camera indoor where constant temperature can be maintained. 2) Set the guideline to guide the subject to target position;... -
Page 8: Alarm Function
2. Alarm Function 2.1 The Camera Alert Function 2.1.1 Alert on Thermal Image As mentioned in ‘How to register to NVR or NMS’, the camera can be connected with NVR or VMS. Either device, the alert image is the same. When temperature higher than pre set-up ‘Event Max Temperature’... -
Page 9: When Using Vms On Pc
2.3 When using VMS on PC As mentioned in ‘1.3.2 Connect with VMS on PC (IDIS Center & ISS Client)’, there are two ways to connect DC-TH201x to VMS. 2.3.1 Connecting to VMS through NVR When connected to PC through NVR and the motion alarm is generated triggering the ‘Event Max Temperature’, Event is sent properly to VMS. -
Page 10: Hardware Factory Reset
3. Hardware Factory Reset Wear an anti-static bracelet and insulating gloves before resetting the device. ※ When resetting the camera, keep the power on. ※ For W/WR model, factory reset function is applied from F/W version ※ ‘HiDual_V5.0.1.200603-060309’ 3.1 DC-TH2011 1. - Page 11 3.2 DC-TH2011W/2W 1. Loosen the bolts on the back of 2. Press M/B Factory reset button for DC-TH2011W/12W using a hexagon 5 seconds wrench 3.3 DC-TH2011WR/2WR 1. Loosen the screws on the back of 2. Press M/B Factory reset button for DC-TH2011WR/12WR.
-
Page 12: Notes On Use
4. Notes on Use 1.1 Notes on installation - When the camera is registered to NVR for the first time, the default resolution is set as the highest - the visual mode resolution. Therefore, the resolution must be adjusted to thermal image viewable resolution referred in below table. - Page 13 MEMO DC-TH 201x Installation Guide...
- Page 14 IDIS and identifying product names and numbers herein are registered trademarks of IDIS Co., Ltd. All non-IDIS brands and product names are trademarks or registered trademarks of their respective companies. Product appearance, build status, and/or specifications are subject to change without notice. Copyright © IDIS Co., Ltd. All rights reserved.