Related Manuals for CDL 210100U
Summary of Contents for CDL 210100U
- Page 1 Version 1.0 10/15/2020 OWNER’S CDL ULTRASONIC MANUAL FLOWMETERS Models : 210100U | 210150U | 210200U | 210300U © Tous droits réservés – CDL Maple Sugaring Equipment Inc.
-
Page 2: Table Of Contents
INSTALLATION DIAGRAM ....................7 SUMMARY BY MODEL ......................8 DISPLAY OF CURRENT FLOW AND ACCUMULATED VOLUME ........... 9 RESETTING VOLUMES TO ZERO ..................10 CDL MONITORING INTERFACE ..................12 MAINTENANCE ......................... 14 WARRANTY ........................15 CDL Maple Sugaring Equipment Inc. -
Page 3: Introduction
• The flowmeters come pre-programmed from the company. You do not need to adjust the settings. By default, the display will be in gallons. However, you will be able to see it in litres on your CDL monitoring interface if you wish. See the CDL Monitoring Interface section. -
Page 4: Product Features
PRODUCT FEATURES Power supply: 24V DC Flowmeter material: PVC Accuracy: ± 1% Maximum pressure: 150 PSI Maximum temperature: 60 degrees Celsius or 140 degrees Fahrenheit Protection: IP68 CDL Maple Sugaring Equipment Inc. -
Page 5: Installation Diagram
2. Reduce turbulence inside the tube as much as possible to ensure accuracy. 3. The controller and Mesh communication module can be screwed into the desired location. INSTALLATION DIAGRAM Output Input Direction of flow Note: The *** ID *** is inner diameter CDL Maple Sugaring Equipment Inc. -
Page 6: Installation Diagram
INSTALLATION DIAGRAM Correct if flow rate controlled by a valve Incorrect if flow rate controlled by a valve CDL Maple Sugaring Equipment Inc. -
Page 7: Installation Diagram
INSTALLATION DIAGRAM CDL Maple Sugaring Equipment Inc. -
Page 8: Summary By Model
5x x ID = Straight line (no elbows) of 10’’ minimum before the flowmeter’s inlet 3 '' Model 210300U 10x ID = Straight line (no elbows) of 30’’ minimum before the flowmeter’s inlet 5x x ID = Straight line (no elbows) of 15’’ minimum before the flowmeter’s inlet CDL Maple Sugaring Equipment Inc. -
Page 9: Display Of Current Flow And Accumulated Volume
If the display does not show the current flow rate and accumulated volume, follow the steps below. Step 1: Press to see “Window No.” on the screen, as below. Step 2: Press: Step 3: Press : CDL Maple Sugaring Equipment Inc. -
Page 10: Resetting Volumes To Zero
Step 2: Enter the number 37 using the keypad by pressing followed by Step 3: Press . The screen should display this: Step 4: Press once to select YES. The screen should display this: Step 5: Press . The screen should display this: CDL Maple Sugaring Equipment Inc. - Page 11 . The screen will briefly show this: Step 8: Press to see “Window No.” on the screen, as below. Step 9: Press , and after Step 10: Make sure the value displayed is zero, as shown below. CDL Maple Sugaring Equipment Inc.
-
Page 12: Cdl Monitoring Interface
CDL MONITORING INTERFACE Step 1: Find your flowmeter, which is connected to the CDL monitoring system, in the interface. In the Device tab, click on Flowmeters. You will be redirected to this page, where you will see your flowmeter’s number. - Page 13 Step 2: Rename your flowmeter as desired. Click here Enter the desired name here and save. To view a flowmeter’s data, simply click on its tab. Click here CDL Maple Sugaring Equipment Inc.
-
Page 14: Maintenance
This will give you access to specific, advanced information for your flowmeter such as: • Flowmeter name • Station name • Last communication with CDL monitoring system • Communication delay with CDL monitoring system • Current flow rate • Total accumulated for the day •... -
Page 15: Warranty
Your flowmeter is covered by a one-year limited warranty. For one year from the date of original purchase, CDL Maple Sugaring Equipment Inc. will repair or replace parts of this flowmeter that are defective in material or workmanship provided that the flowmeter is installed, operated, and maintained according to the instructions provided. - Page 16 CDL Maple Sugaring Equipment Inc. shall not be held responsible for incidental or indirect damages or for material and implicit damages. Some states and provinces do not allow limitations or exemptions on incidental or indirect damages or limitations on warranties.