Related Manuals for CDL 210100
Summary of Contents for CDL 210100
- Page 1 Version 1.0 10/15/2020 OWNER’S CDL ROTOR MANUAL FLOWMETERS Models : 210100 | 210150 | 210200 | 210300 © Tous droits réservés – CDL Maple Sugaring Equipment Inc.
-
Page 2: Table Of Contents
INTRODUCTION ........................3 PRODUCT FEATURES ......................4 RESETTING TO ZERO ......................5 INSTALLATION ........................6 INSTALLATION DIAGRAM ....................7 SUMMARY BY MODEL ......................8 CDL MONITORING INTERFACE ................... 9 MAINTENANCE ......................... 11 WARRANTY ........................12 CDL Maple Sugaring Equipment inc. -
Page 3: Introduction
• The flowmeters come pre-programmed from the company. You do not need to adjust the settings. By default, the display will be in gallons. However, you will be able to see it in litres on your CDL monitoring interface if you wish. See the CDL Monitoring Interface section. -
Page 4: Product Features
Maximum temperature: 60 degrees Celsius or 140 degrees Fahrenheit Protection: IP66 1 '' model 210100: Minimum flow rate = 2.5 GPM Maximum flow rate = 79 GPM 1 ½ '' model 210150: Minimum flow rate = 6.5 GPM Maximum flow rate = 225 GPM 2 '' model 210200: Minimum flow rate = 10.5 GPM Maximum flow rate = 357 GPM... -
Page 5: Resetting To Zero
RESETTING TO ZERO Displays accumulated gallons Display flow rate in gallons per minute (gpm) Important To reset the accumulated gallons to zero, press and hold these two buttons for 3 seconds. CDL Maple Sugaring Equipment inc. -
Page 6: Installation
1. As a basic principle, the tube should always be full so that the flowmeter can get a proper reading. 2. Reduce turbulence inside the tube as much as possible to ensure accuracy. 3. The Mesh communication module can be screwed into the desired location. CDL Maple Sugaring Equipment inc. -
Page 7: Installation Diagram
Correct if flow rate controlled controlled by a valve by a valve 10x ID 5x ID correct incorrect 10x ID 5x ID 5x ID correct incorrect 10x ID Note: The *** ID *** is inner diameter CDL Maple Sugaring Equipment inc. -
Page 8: Summary By Model
5x x ID = Straight line (no elbows) of 10’’ minimum before the flowmeter’s inlet 3 '' Model 210300 10x ID = Straight line (no elbows) of 30’’ minimum before the flowmeter’s inlet 5x x ID = Straight line (no elbows) of 15’’ minimum before the flowmeter’s inlet CDL Maple Sugaring Equipment inc. -
Page 9: Cdl Monitoring Interface
CDL MONITORING INTERFACE Step 1: Find your flowmeter, which is connected to the CDL monitoring system, in the interface. In the Device tab, click on Flowmeters. You will be redirected to this page, where you will see your flowmeter’s number. - Page 10 Step 2: Rename your flowmeter as desired. Click here Enter the desired name here and save To view a flowmeter’s data, simply click on its tab. Click here CDL Maple Sugaring Equipment inc.
-
Page 11: Maintenance
This will give you access to specific, advanced information for your flowmeter such as: • Flowmeter name • Station name • Last communication with CDL monitoring system • Communication delay with CDL monitoring system • Current flow rate • Total accumulated for the day •... -
Page 12: Warranty
Your flowmeter is covered by a one-year limited warranty. For one year from the date of original purchase, CDL Maple Sugaring Equipment Inc. will repair or replace parts of this flowmeter that are defective in material or workmanship provided that the flowmeter is installed, operated, and maintained according to the instructions provided. - Page 13 CDL Maple Sugaring Equipment Inc. shall not be held responsible for incidental or indirect damages or for material and implicit damages. Some states and provinces do not allow limitations or exemptions on incidental or indirect damages or limitations on warranties.