Related Manuals for OpenSprinkler OpenSprinkler v3
Summary of Contents for OpenSprinkler OpenSprinkler v3
-
Page 1: Table Of Contents
6. Run-Once Program 7. Programs 7.1 Program Data 7.2 Program Preview 7.3 Zone's Sequential Attribute 8. Logging 9. Firmware Update, FAQ, Support, and Github Advanced Topics 1. Installing Radio Frequency (RF) Transmitter Specifications OpenSprinkler Firmware 2.1.9 User Manual... -
Page 2: Introduction
Ethernet module), O penSprinkler 2.3 (wired Ethernet only), and O penSprinkler Pi (or OSPi, driven by an RPi). OpenSprinkler v3 and 2.3 are fully assembled and come with pre-flashed firmware. OSPi requires some assembly steps (e.g. plugging in your Raspberry Pi) and firmware installation. For all versions, ... -
Page 3: Hardware Interface
Hardware Interface OpenSprinkler Firmware 2.1.9 User Manual... -
Page 4: Zone Wire Connection Diagrams
● ● If you have a master or pump start relay wire, you can insert it into any zone port -- OpenSprinkler uses software defined master / pump zone so you can dedicate any zone as a master zone. Installation Important Notes ... - Page 5 (AC has no polarity so the two wires have no distinction); For O penSprinkler DC or L ATCH , insert the DC power adapter into the power barrel on OpenSprinkler. ● For additional details on how to connect sensors (e.g. rain or flow sensor), refer to the ...
- Page 6 ○ In WiFi mode, the first time you power on OpenSprinkler (or every time after a factory reset), it s tarts as a WiFi AP (Access Point) , creating an open WiFi network with SSID displayed on the LCD screen (e.g. ...
-
Page 7: Lcd And Button Functions
Pressing and holding the following buttons w hile the OpenSprinkler Logo is displayed at reboot : If B 1 is pressed and held while logo is displayed at reboot: enter F actory Reset . ... -
Page 8: Firmware 2.1.9 User Manual
OpenSprinkler’s built-in web interface works with both desktop and mobile browsers. It allows you to change settings and modify programs at any time using e ither a web browser or the free OpenSprinkler mobile app . To install the mobile app, just search o pensprinkler in your app store. ... -
Page 9: Device Status
● Disable Operation : d isables zone operations. This is useful if OpenSprinkler will not be used for a period of time. Change Password : c hange device password (default is o pendoor ) . ... -
Page 10: Menu Buttons
Cloud Synced Attributes : once you log in to opensprinkler.com in the UI/app (through sidebar menu), cloud-synced attributes will become available, including station photos and notes. You can take a custom photo for each station by using the OpenSprinkler mobile app. ... - Page 11 Sensor Installation: a ll sensors described below have two wires (except the 3-wire flow sensor). To install Sensor1: insert the two wires to the sensor terminals. On OpenSprinkler v3, insert the two wires to SN1 and GND. To install ...
- Page 12 You can modify the message body later to suit your need. ● Select Events : g o back to the OpenSprinkler app / UI, click ‘Configure Events’. The following events are supported: Program Start: triggered when a program is scheduled. ...
-
Page 13: Run-Once Program
● Boost Time : t his option is o nly applicable to DC-powered OpenSprinkler . It sets the DC voltage boost time (from 0 to 1000ms). Default is 320ms. When using a low-voltage DC power adapter, such as 5VDC, to drive 24VAC sprinkler valves, ... -
Page 14: Programs
90 minutes for 7 times. This is useful for breaking down long water times into shorter cycles. Unlike previous firmwares, this firmware allows repeating start times to go overnight to the next day. OpenSprinkler Firmware 2.1.9 User Manual... -
Page 15: Program Preview
Attribute OpenSprinkler supports r unning multiple zones in sequence (one after another) or parallel (concurrently) . This can be set using each zone's S equential attribute. Zones that have the Sequential attribute turned on will be automatically serialized. For ... -
Page 16: Firmware Update, Faq, Support, And Github
A NT pin on the transmitter. The wire can be straight or curled like shown in the picture below. ● OpenSprinkler v3 has built-in receptacle pin header for the RF transmitter. You can directly plug in an RF transmitter (3-pin) on the top side. The orientation is such that i t's facing up . See the ...
Need help?
Do you have a question about the OpenSprinkler v3 and is the answer not in the manual?
Questions and answers