Advertisement
5. OpERATION
5.1.
BRAKE BLEEDING pROCEDURE
5.1.1.
Refer to the vehicle manufacturer's instructions for brake bleeding and wheel sequence before proceeding.
WARNING! Familiarise yourself with the hazards of brake fluid - read manufacturers instructions on the container. DO NOT touch the
‰
vehicle's brake pedal whilst bleeding the brakes.
5.1.2.
Remove the cap of the vehicle's brake fluid reservoir. If the fluid level is not at maximum top it up.
5.1.3.
Remove the cap assembly (fig.1-A) from the replenishment bottle and invert it within the neck of the reservoir as shown in fig.1. The
threaded outlet 'B' must be immersed in the brake fluid. If it is not, rotate the three legged moulding 'C' clockwise towards the valve 'D'
until sufficient thread is exposed to allow the outlet to be immersed in the brake fluid.
5.1.4.
Ensure the valve is closed as shown in fig.1-D.
5.1.5.
Fill the replenishment bottle just under half full with new brake fluid and screw the cap assembly back down onto the bottle. Invert
the bottle over your container of new brake fluid and open the valve so that the fluid level begins to drop towards the level marked on
the bottle. As soon as the level mark is reached close the valve.
5.1.6.
Place the bottle into the neck of the vehicle brake fluid reservoir as shown in fig.1. and open the valve. As the brakes are bled the fluid
level in the reservoir will begin to drop and expose the bottle outlet. Brake fluid will begin to flow from the replenishment bottle. Once
the level in the reservoir has risen sufficiently to cover the outlet the flow will automatically stop.
5.1.7.
Connect the brake bleeder to a suitable compressed air supply.
5.1.8.
Mount the black rubber pipe onto the brake nipple on the first wheel and open the nipple about ¼ of a turn (fig.2).
5.1.9.
Activate the brake bleeder's trigger. The vacuum created will draw the brake fluid from the vehicle's brake system.
5.1.10.
Continue to bleed the system until there are no air bubbles visible in the clear tube (fig.3).
5.1.11.
Close the brake nipple (fig.2).
5.1.12.
Remove the rubber pipe from the brake nipple.
5.1.13.
Depress the trigger to clear brake fluid from the clear pipe.
5.1.14.
Repeat the process at each wheel in turn.
5.2.
ChANGING ThE BRAKE FLUID
5.2.1.
Repeat the brake bleeding procedure as described above. As the fluid is being completely changed regularly check the level in the
replenishment bottle.
5.2.2.
When new fluid can be seen in the clear tube tighten the brake nipple.
5.2.3.
Repeat this procedure at every wheel. When brake bleeding and/or fluid changing is complete, test the action of the brake pedal to
ensure that the brakes are working correctly, before driving the vehicle on the road.
.
fig.1
ENVIRONMENT pROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey Group, Kempson Way, suffolk Business park, Bury st Edmunds, suffolk. Ip32 7AR
01284 757500
© Jack Sealey Limited
fig.2
01284 703534
sales@sealey.co.uk
Original Language Version
fig.3
www.sealey.co.uk
VS021.V3 | Issue:3 (H,F) 22/08/19
Advertisement
