Table of Contents
Advertisement
Operating Manual - PROTEA SYSTEM II 4.24D Distribution / System Processor
8.5 Factory Reset
Factory reset is used to clear all user defined preset names and control values and reset them to their original
factory settings. Factory reset to the 4.24D is accomplished by pressing and hold the MIDI Channel select switch on
the front panel during power up. There will be a countdown in the MIDI Channel display to indicate a factory reset is
occurring. Releasing the switch or shutting off power at any time during the countdown will stop the factory reset
from occurring. At the end of the countdown, a successful factory reset is indicated by a lower case "r" in the display,
followed by normal operation of the unit.
9. TROUBLESHOOTING
9.1 - Audio Troubleshooting Tips
1.) No power - Is the detachable AC cord fully plugged in? Is the rear panel power switch on?
2.) Software controls don't work - Is the RS-232 cable properly installed to the PC? Is the software commu-
nications enabled? Is the software device set to 4.24D (section 6.3)? Check the security level (section 8.4). If set to
<Lock 4.24D>, or <Lock Protea System Software>, then Protea unit is "view only" and controls cannot be changed.
Does the MIDI channel assignment match between software and 4.24D (section 4.3-4.4)?
3.) No sound - Check to see if the input or output is muted. Is the input or output Gain turned down? Check
the selected audio source(s) for each output, making sure there is signal applied to the designated input(s). If used as
a crossover, make sure the high pass filter (HPF) is set to a lower frequency than the low pass filter (LPF) for a given
output.
4.) Clip light stays on - Is the input signal level too high? Check to see that the nominal input level is 0dBu,
allowing 20dB of input headroom. Are input or output gain settings too high? Check to see if an EQ filter has too
much boost.
5.) Distorted sound but no Clip LED- Check individual EQ filters to see if there is excessive boost.
6.) Muffled sound - If expecting full range audio on an output, make sure the crossover settings are not
inadvertently set so as to limit the pass band.
7.) Excessive Noise - An input signal level or an input gain setting that is too low could require the loss to be
made up for at the output gain stage, producing more noise than a properly set up gain structure. Do not use the 4.24D
for dramatic increases in level, but rather optimize the signal source for a nominal 0dBu output.
8.) Forgot the password - See section 8.4
9.2 RS-232/MIDI Troubleshooting Tips
1.) Test all data cables. Use standard MIDI cables and RS232 data cables with all conductors wired straight
through. Monitor cables and Null Modem cables use non-standard wiring schemes, they will not work with a Protea.
2.) Use a valid PC serial port. You must use a serial port that is not opened to any other application, such as a
mouse, modem, or another program. To verify that the port exists look in: Control Panel - System - Device Manager
- Ports. While you're there, make sure that the port has no warnings or conflicts. There is no need to change the port
settings because Protea System Software will do this automatically. Finally, you must select the valid port in Protea
System Software. This is done under the Communications heading - Com Port Assignment.
3.) Make sure that the RS-232 mode switch, located on the back of 4.24D, is in the "out" position. There is
just one exception to this rule: the RS-232 mode switch gets pushed in only when both the RS232 Dataport is con-
nected to a PC, and the 4.24D is part of several Protea products in a MIDI chain.
4.)
4.)
4.) Make sure the MIDI channel assigned to the 4.24D matches the MIDI channel chosen for the device
4.)
4.)
within Protea System Software, and make sure that no other devices use that MIDI channel.
16
Hide quick links:
Advertisement
Table of Contents
