ION Total PA Premier Quick Start Manual

Total PA Premier Quickstart Guide
Box Contents
Total PA Premier Remote Control
Microphone & Cable Power Cable (IEC)
Telescoping Speaker Stand Quickstart Guide/Safety & Warranty Information
Features
1.
2
3
4
1
11 12 13 14
15 16
6 6 9
17
2.
5 5
7
18
3.
5 5 8
10
4.
5.
6.
7.
8.
Pairing a Bluetooth Device
1. Turn on your Bluetooth device.
2. Power on Total PA Premier.
3. Use the Mode button to select Bluetooth as the audio source, which appears as "bt" in
the display. Total PA Premier will automatically go into pairing mode to search for
Bluetooth devices. You will know you are in pairing mode when the Bluetooth icon is
flashing. In addition, automatic voice prompts from the speaker will alert you of the
device's status: Bluetooth
Disconnected.
4. Navigate to your Bluetooth device's setup screen, find Total PA Premier, and connect.
The Bluetooth icon will remain solidly lit.
Note: Users should consider updating their device's OS if experiencing trouble with
pairing or playing music.
5. To disconnect pairing, turn off Bluetooth on your device or select Forget this device on
your Bluetooth device's setup screen.
If you would like to disable (or enable) the voice prompts, press and hold the Play/Pause
button on the Media Panel.
Note: Bluetooth must be selected as the audio source in order to disable (or enable) the
voice prompts.
App Control
IMPORTANT: To ensure the best possible experience with the app, use the most current
Android OS or iOS on your device.
Note: Ensure that your device has internet access via your service provider or wireless
connection. You can also download the app on your computer, but remember to connect and
sync your device to transfer the app.
Follow these steps to download the free app on your device:
1. Open the Apple App Store or Google Play on your device.
2. Search for the ION Sound XP app.
3. Follow the on-screen instructions to download and install the app.
4. Once downloaded, the ION Sound XP app will appear on your device's home screen.
Speaker Stand Installation
1. Fully extend the speaker stand tripod legs on a flat, stable surface. Look in the box
contents under the foam sheet for the rubber feet and speaker stand mounting knob.
2. Raise the mounting pole up to the appropriate height needed and tighten the side
adjustment knob.
3. Insert the pin into the bottom pin-hole so the mounting pole stays at your set height.
4. On Total PA Premier, adjust the bottom knob counter-clockwise so the screw is not
blocking the opening.
5. Line up the Total PA Premier mounting hole with the speaker stand pole and place on
the pole.
6. Tighten the mounting knob clockwise on Total PA Premier.
9.
Media Panel: Aux Input Volume
Mode
10. Mix Out (XLR)
11.
Mic Echo
Play/Pause
12. Low EQ
Repeat
13. High EQ
Previous/Back
14. Master Volume
Next/Forward
USB Port 15. Power LED
16. Clip LED
SD Card Slot
Display 17. Link
18. Light Mode
Mic Inputs (1/4", XLR)
Mic Input Volume 19. Power Cable Input
20. Fuse Holder
Aux Input (1/8")
XLR Input 21. Power Switch
Pairing, Bluetooth Connected,
Support
Thank you for purchasing the Total PA Premier. At ION, your entertainment is as important
to us as it is to you. That's why we design our products with one thing in mind—to make
your life more fun and more convenient.
IMPORTANT: For the full User Guide, visit ionaudio.com.
IMPORTANTE (en Español): Descargue la Guía del Usuario completa de ionaudio.com.
For the latest information about this product (documentation, technical specifications,
system requirements, compatibility information, etc.) and product registration, visit
ionaudio.com.
For additional product support, visit ionaudio.com/support.
Caution: Do not expose Total PA Premier to rain or standing water.
Linking Two Speakers
To wirelessly link two Total PA Premier speakers:
1. Power on both speakers using their Power Switches.
2. With no Bluetooth connected, press the Mode button on one Total PA Premier to select
Bluetooth as the audio source, which appears as "bt" in the display. This will be the
"secondary" speaker.
3. Press the Link button on a second Total PA Premier to enter Stereo Link Mode. This
will be the "primary" speaker.
4. Wait up to 1 minute for the speakers to make the connection. Once the two speakers
are linked, press the Mode button on the "primary" speaker to select the desired audio
source. Use the directions
5. To disconnect, double-press the Link button on the "primary" speaker.
To link two Total PA Premier speakers using cables:
1. With the Power Switch on each speaker turned to the off position, connect each
speaker to a power outlet.
2. Plug an XLR cable into the Mix Out located on the rear panel of one Total PA Premier
speaker. This speaker (the primary) is the one to which you will connect audio sources
such as a Bluetooth device, microphone, or USB flash drive.
3. Plug the other end of the XLR cable into the XLR Input on the rear panel of your
second Total PA Premier speaker. This second speaker will receive the audio from any
devices connected to the first speaker (the primary).
or Bluetooth
4. Power on both speakers using their Power Switches.
5. Connect your audio sources to the first speaker (the primary).
6. Make sure that each speaker's Master Volume control is set to the same position.
7. With one of your audio sources playing, gradually turn up the Aux Input Volume on the
second Total PA Premier speaker until the volume of this speaker matches the volume
of the first speaker (the primary).
Light Modes
Press the Light Mode button to toggle between five modes for the lights on the front panel:
1. Color Wheel: The lights spin on and around the woofer.
2. Color Wheel Beat Sync: The lights spin on and around the woofer according to the
tempo of the music playing.
3. Color Cycle: The lights steadily cycle through different colors.
4. Beat Sync: The lights flash and change colors according to the tempo of the music
playing.
5. Off
Technical Specifications
Output Power: 500 W (peak)
Frequency Response: 55 Hz – 20 kHz (+3 dB)
Drivers:
Low-Frequency: 15.0" / 381 mm woofer
High-Frequency: 1.0" / 25 mm tweeter
Crossover: 2.2 kHz
Bluetooth:
Profile: A2DP, AVCTP
Module: Bluetooth 5.0
Range: Up to 100 ft. (30.5 m) *
* Bluetooth range is affected by walls,
obstructions, and movement. For optimal
performance, place the product in the center
of the room so it is unobstructed by walls,
furniture, etc.
Trademarks & Licenses
ION Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. App
Store is a trademark of Apple Inc., registered in the U.S. and other countries. Android and Google
Play are registered trademarks of Google Inc. The Bluetooth word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by ION Audio is under license. All other product
names, company names, trademarks, or trade names are those of their respective owners.
Manual Version 1.4
above to connect your Bluetooth device.
USB Charging Port: +5 V, 1 A
USB/SD:
Supported File System: FAT32
Supported File Types: MP3
Max. File Size: < 64 GB
Max. Device Capacity: < 64 GB
Power:
Connection: IEC
Input Voltage: 100–120 VAC; 60 Hz
Dimensions (WxDxH): 17.8" x 14.6" x 28.2" /
451 x 370.5 x 716 mm
Weight: 42.44 lbs. / 19.25 kg