Subscribe to Our Youtube Channel
Related Manuals for Tempest Whispr G4
Summary of Contents for Tempest Whispr G4
- Page 1 User Manual Whispr G4 Revision 02.1 July 2020 © Tempest Lighting, Inc. Whispr G4 User Manual...
-
Page 2: Table Of Contents
Projector Mount - Portrait Enclosures ..............................20 Flipping the Portrait Orientation ..............................21 Routine Maintenance ....................................22 Check the following every six months: ..............................22 Clean Port Glass ....................................22 Check Filter ....................................... 22 For After Sales Support ..................................22 Whispr G4 User Manual... - Page 3 Troubleshooting ......................................23 Warranty ........................................24 Whispr G4 User Manual...
-
Page 4: Approvals - North America
This is to certify that the following products: 56.xxx.US Series Whispr G4 Projector Enclosures Have been tested and approved to standards UL 508 (electrical) and UL 50 (environmental), as NEMA 3R enclosures, for use in the United States and Canada. -
Page 5: Approvals - Europe
+1 818 787 8984 f: +1 818 252 7101 e: info@tempest.biz www.tempest.biz Tempest Lighting, Inc. declares that t heir Whispr G4 Projector Enclosure Series 56.xxx.xx complies with the Essential Requirements of the fo llowing EU Directives: Low Voltage Directive 2006/95/EC Test Report G4.51.LVD... -
Page 6: Approvals - China
Approvals – China Whispr G4 User Manual... -
Page 7: Introduction
In the event of difficulty, please contact your Tempest reseller or Tempest direct: info@tempest.biz +1 818 787 8984 We will do everything we can to help you get the very best results from your Tempest enclosure. IMPORTANT: Safety Advisories •... -
Page 8: Installation
Short Throw tbd* tbd* tbd* tbd* tbd* tbd* tbd* 1,800W *tbd – please consult factory ** Be sure to allow for the length of the lens and for connectors, cables and cable bend radii when calculating dimensions Whispr G4 User Manual... -
Page 9: Access Clearance
Mounting Hardware Options IMPORTANT SAFETY NOTICE Installer must ensure that all mounting points are secure and conform to local safety regulations. Tempest Lighting Inc. accepts no responsibility for damage or injury arising from inappropriate or unsafe installation. M10-1.5 bolts... -
Page 10: Mounting Tabs
(not supplied). May also be used to hang using threaded drop rods. Hang using M10-M12 (US 3/8”-1/2”) threaded drop rods… …or bolt from below into an overhead frame or structure Whispr G4 User Manual... -
Page 11: Installing Duct Hoses And Fans
Inlet Hose, in S audience from the enclosure’s exhaust fan. configuration Tempest recommends locating the exhaust fan in a separate for best noise location, ideally on the other side of a wall from the audience attenuation space. Where this is not possible, it will be necessary to install acoustic insulation between the exhaust fan and the audience space. -
Page 12: Whispr Fan Kit
Connect the enclosure end to the fan terminals in the a roof void. Whispr wiring compartment (see below) Fan wiring terminal cover Fan wiring terminals Mounting holes (for ducts) Duct Adapter Ring Mounting holes (in free air) For mounting locations, see drawing on next page. Whispr G4 User Manual... -
Page 13: Whispr Remote Blower Drawing
Whispr Remote Blower Drawing Whispr G4 User Manual... -
Page 14: Wiring And Fan Speed Setup
All electrical work must be done in full compliance with all electrical and safety norms applicable to the installation site. Isolate all power feeds before opening the enclosure. Tempest Lighting, Inc., its employees and agents will not be held responsible for damage or injury caused by disregarding this notice. -
Page 15: Power Wiring And Fan Speed Control
Connect FAN N, E Connect live fan wire to the desired fan speed terminal: F1 Slow F2 Medium F3 Fast Thermostat Note: Illustration shows European wire colors. For clarity, internal wiring is not shown. Whispr G4 User Manual... -
Page 16: Capacitor Wiring
Set the thermostat temperature to approximately 90°F, or 30°C, using the blue temperature adjustment dial Thermostat temperature adjustment Adjust so that the fan does not run when the projector lamp is off, but starts soon after the lamp turns on Whispr G4 User Manual... -
Page 17: Projector And Aux Power
Two rewireable C14 plugs are included. Thermostat Projector and aux power outlets The C13/14 connectors are rated as follows: 100-120VAC 15 Amp 200-250V AC 10 Amp Whispr Operation Whispr operation is automatic, controlled by the thermostat described above. Whispr G4 User Manual... -
Page 18: Mounting The Projector
(left slide shown here). • Now that most projectors have the same vertical lens shift in both directions, tabletop (feet down) installation is standard. • For Ceiling-style (feet-up) installation, see the 52.FU Kit below. Whispr G4 User Manual... -
Page 19: Projector Mount - Feet-Up Kit
Align the projector and clamp in place with the projector clamps. The Feet-up kit comes with two sets of legs, for 50mm and 75mm (3in) 50mm (2in) 25mm (1in) 75mm heights. For 25mm height, discard the legs. Whispr G4 User Manual... -
Page 20: Projector Mount - Portrait Enclosures
Note: it may be helpful to remove the projector feet. For clarity, the portrait mount is shown here outside the enclosure Projector mounting screw and washer M8 Washer & Locknut Projector Bar M8 Carriage bolt Portrait Mount Frame Whispr G4 User Manual... -
Page 21: Flipping The Portrait Orientation
Some projectors may only be used in portrait mode in one orientation – feet left or feet right. You can flip the projector mount to accommodate either type. Just remove the eight projector bridge screws, rotate the mounting assembly 180°, and re-install. Projector Bridge Screws Whispr G4 User Manual... -
Page 22: Routine Maintenance
The filter clamp will drop out Remove filter Wash filter with warm water and mild detergent if needed Dry filter Replace Electrostatic Foam Filter Filter Clamp For After Sales Support Contact your Tempest dealer or email info@tempest.biz Whispr G4 User Manual... - Page 23 Is the fan running when the projector lamp is on? If not, reduce the thermostat temperature setting Dirt/Debris inside enclosure Filter is either missing or damaged? Filter is not properly seated Side panels or back door not firmly latched None of the above? Contact info@tempest.biz Whispr G4 User Manual...
- Page 24 SELLER AGREES THAT IT WILL, AS THE SOLE AND EXCLUSIVE REMEDY UNDER THE CONTRACT OR OTHERWISE, FOR ANY NONCONFORMITY OR BREACH OF WARRANTY, AND AT SELLER'S SOLE ELECTION: (i) REPAIR SUCH GOODS; OR (ii) REPLACE SUCH GOODS. Whispr G4 User Manual...
Need help?
Do you have a question about the Whispr G4 and is the answer not in the manual?
Questions and answers